Search Documents

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By David A. Smith

A new generation of reliable, stable, and easy to use bulk emulsions allowing application in tunneling and drift rounds has been developed. This new product group of bulk emulsions has been especially formulated for use in small-diameter holes and is a significant advancement in bulk emulsion technology. Reliable and easy-to-use bulk delivery equipment has been designed and developed to allow bulk emulsions to be used in a wide variety of shaft and tunneling applications.

Jan 1, 1987

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By J. L. Whitlock

A mutant strain of Pseudomonas paucimobilis is utilized to effectively degrade and or remove 90-98% of cyanide, thiocyanate, toxic heavy metals and ammonia from a cyanidation mill process and mine discharge maximum of 21,000 m3/d (5.5 MGD). Homestake Mining Company?s biological wastewater treatment plant has been in full scale operation for over 2 years at the Homestake Mine in Lead, South Dakota.

Jan 1, 1987

By D. Duvris

Health and safety issues are a very important aspect of mining activities. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last 3 decades are presented and critically evaluated with respect to number of workers, annual production, etc. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greek are also discussed.

Jan 1, 2000

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008

By S. K. Palm

The commercial life of a mineral product can be long, but like hitech electronic and software products that soar in sales one day to become obsolete and forgotten a few months or years, mineral products have a life cycle. They are invented, commercialized and eventually decline and disappear from commerce. Diatomite and perlite are produced from mined minerals, but almost none of the products in these industries spring from the earth in finished form. Straight calcined diatomite was invented over 100 years ago and flux calcined diatomite just a few years later. The expansion properties of perlite were discovered and first exploited about 75 years ago. Some applications for diatomite have disappeared or currently face competition from newer products. Dry cleaning was once the second-largest application for diatomite but disappeared over 30 years ago. Both the beer and wine filtration markets for diatomite face increased competition from membrane filters. A pipeline of new, proprietary products is critical to the future of the industry.

Mar 2, 2022

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By R. W. Fedors, S. T. Green, F. T. Dodge, D. B. Walter

Spatial and temporal temperature variations in a high-level radioactive waste repository drift can give rise to moisture transport within the drift. Knowledge of this moisture transport may be important to assessing the potential for corrosion of all metallic components in the drift. The model presented here shows one approach to simulating evaporation, transport, and condensation of water in large underground openings using a framework based on computational fluid dynamics. Simulation results that explicitly model water and latent heat transport are presented.

Jan 1, 2004

By Charles A. Gargano

The current state of the mass transit industry in America will be examined. How and why this important urban activity shifted entirely, or almost entirely, from the private sector to the public sector. Who pays for transit? For day to day operating costs? For capital investment? The prospects for transit's future will be the next major issue addressed. In a word, they are rather good. Over the past decade there have been major new transit investments made in Atlanta, Baltimore, Washington, D.C. and Miami, as well as constant re-investment in such cities as New York, Boston, Philadelphia and Chicago. While the current administration has put a temporary halt on the initiation of any major new rail transit projects using Federal funds, there are several mechanisms localities have for using other resources for such projects. These will be explored.

Jan 1, 1983

By Earl C. Herkenhoff

Editor's note: The subject of mining on the moon can generate a wide range of strongly held opinion, from those leaning toward the view that, ultimately, such activity is the destiny of mankind to those who believe that all suggestions for moon mining to date are unrealistic, wildly expensive and in the hands of people who 'know nothing.' MINING ENGINEERING herewith publishes some of the basic pros and cons on the subject of moon mining by writers who are among those holding strong views on the subject, with the hope that some of our readers may be interested in joining this debate. Every mineralogist and most mineral industry people were keenly interested in the examinations of the first moon rocks brought back by US astronauts in 1969. Suffice to say that the examinations revealed nothing exotic in the mineral makeup of the very limited rock samples. The rocks were generally of igneous type, dark-colored and contained some common, Earth-type minerals. There was, in Earth terms, above average TiO2 content, but they contained nothing of commercial significance by Earth standards. Therefore, interest in moon minerals rapidly faded. Years later, on Sunday, May 4, 1986, living in Reno, NV, this author was shocked to read a local newspaper article by the Dean of the Mackay School of Mines, University of Nevada, Reno, headlined, "Moon Mining Not Far Off." Considering that the announcement more or less coincided with a slump in our domestic mining industry, the immediate questions in a reader's mind

Jan 1, 1991

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

The introduction of computer technology to the mining industry has produced many benefits for the mining engineer. The most significant is the dramatic increase in productivity realized by the individual user. This is important during times of competitive market conditions. Software for the minerals and energy industries has evolved substantially over the past decade. But even today it remains difficult to find a system that features the flexibility and integration capabilities to effectively (and cost-effectively) handle the needs of professionals in each phase of the mining industry - from exploration to reclamation. Several national software developers are now addressing this challenge. One Denver-based company, MINEsoft Ltd., offers a software package that is currently being used in each phase of the mining industry. The basic technology used in MINEsoft's database management system was developed in the 1960s. But during these early years of the computer industry, most of the technology was available only on mainframe computers, and then only as separate entities. MINEsoft's system unifies these various systems in one package that can be used on most computers manufactured today. Database Management System TECHBASE is a flexible, integrated database management system designed specifically for technical applications. The system features a database manager with no practical limit to the amount of data it can store, retrieve, and manipulate, according to the company. TECHBASE in¬cludes Applications Packages (TAPs) designed to meet the needs of professionals in a host of industries. Clients use the TECH BASE system to prepare many reports, including important EPA information. The package reduces data to a manageable level and enables users to increase productivity with a smaller staff. Mining engineers no longer need to do things by hand. What used to be a day's work can be accomplished in an hour or two. Exploration "Using the TECHBASE system to generate maps has probably saved us the expense of three or four draftsmen," says Ralph Fitch, regional manager and senior staff geologist with Chevron Resources in Portland, ME. "The system has great flexibility. You can treat it much like a spreadsheet. If you are halfway through with a particular project, the system allows you to add fields and calculations with ease but without starting over." Fitch uses TECHBASE for the "straightforward" plotting of results and generation of geochemical and geophysical profiles. "In exploration," he says, "these are the two key elements ... the generation of maps and data profiles. The system allows you to plot as many elements and variables in these areas that you like." Other aspects are important, too, says Fitch, including drill hole sections. "We use all the basic capabilities the system provides in the complete package," he explains. "When shopping for a system, TECHBASE was clearly dedicated to exploration in the

Jan 9, 1987

By Michael Moats, Weston Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the USA. Electric arc furnace dusts processed to recover zinc produce a process residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine the predominant mineral phases and leached with common mineral acids. Atmospheric agitated leaching using sulfuric acid and hydrochloric acid were examined to determine the extractions of gallium, indium, and germanium as a function of concentration, temperature, and time. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 82%, ~100%, and 89%, respectively.

Aug 8, 2023

By Shi Wang, Hongbin Liu, Meiliang Wei, Wu Liu, Xiaojun Wang, Yuxian Ke, Xuepeng Song, Tiejun Tao

The study investigates the influence of water migration on the fluidity of fresh cemented paste backfill (CPB) with and without flocculant under variable shear rates. The research utilizes nuclear magnetic resonance (NMR), rheological tests, and scanning electron microscopy (SEM) to analyze water migration, rheological properties, and microstructure evolution. The findings reveal that water migrates to more stable states as shear rate increases, and the addition of flocculant enhances water migration and increases shear stress and apparent viscosity. The study establishes relationships between water content and rheological parameters, providing insights into the flow characteristics of fresh CPB for pipeline transportation.

May 4, 2022

By Gary D. Aho

The United States on a daily basis no consumes about 15MM barrels (2.38 x 106m3) of oil; 5MM (0.79 x 106 m3) of this is imported. This compares tai a daily consumption of 18MM (2.86 x 106 m3) in 1980 when we imported 8MM (1.27 x 106 m3). We are producing the 10MM barrels (1.59 x 106 m3 ) of conventional oil at home from what amounts to just 2% of our domestic energy reserves. Nearly 90% of our total domestic energy reserves occurs in solid forms such as coal, oil shale, and tar sands; this is more than enough to meet our needs for the next 100 years. Worldwide, oil shale is second only to coal as a potential source of energy and the U.S. has approximately one-half of the world oil shale reserves which average over 25 gallons per ton (10.43 x 10-2 L/kg). Since the United States has immense oil shale resources, including some of the richest in the world, and since oil shale produces a superior transportation fuel, it would seem logical that the U.S. would be prudently developing this domestic resource. Unfortunately, despite over 50 years of research and a number of false starts, there is not a commercial shale oil industry in place today. There are a number of recurring roadblocks which have hindered private industry's efforts to develop oil shale and we will look at some of these.

Jan 1, 1983

By Robert D. Coyle, David L. Emmons

Introduction The Cove gold-silver deposit is located in Lander County, NV about 50 km (30 miles) southwest of Battle Mountain, NV (Fig. 1). The deposit is in the north-central part of the Fish Creek Mountains within the McCoy mining district. Gold was first discovered in the McCoy district in 1914 by Joseph H. McCoy (Vanderburg, 1939). From 1928 to the early 1930s, minor production occurred from shallow underground workings. Total gold production was less than 311 kg (10,000 oz; Stager, 1977). The district was inactive until the mid-1960s when it was explored by Bear Creek Mining, Summa Corp., Houston Oil and Minerals Corp., Gold Fields, and Tenneco Minerals. Tenneco began a detailed reevaluation of the McCoy deposit in the fall of 1984. Tenneco's decision to place the deposit into production was based on a geological reserve of 8.7 t (280,000 oz) of gold (Kuyper, 1987). Subsequent exploration and development drilling of the McCoy skarn deposit has more than doubled the mineable skarn reserves to 19 t (615,000 oz) of gold. In September 1985, Tenneco began development work on the McCoy gold-skarn deposit. The project is an open-pit, heap leach mine. The first gold was poured in April 1986. Echo Bay Mines acquired Tenneco's precious metals properties in October 1986. The mining operation and district exploration started by Tenneco is continuing under the Echo Bay's ownership. The Cove deposit was discovered in January 1987 and production began in February 1988. The deposit will begin as an open-pit, heap leach operation. It will be converted into an open-pit and underground mine with a 9-kt (10,000-stpd) mill. Geologic setting The Cove gold-silver deposit is situated on the east flank of the Fish Creek Range. Surface elevations range from 1460 to 1680 m (4800 to 5500 ft). The deposit is 1.6 km (1 mile) northeast of the McCoy gold-skarn deposit. The Cove deposit is hosted by the Augusta Sequence of Triassic age. Three formations of the sequence are mineralized at the Cove. In ascending order they are the Favret, Panther Canyon, and Augusta Mountain formations. The Favret formation is a gray, locally silty limestone that is commonly fossiliferous. The base of the formation is not exposed. Exposed and drilled intervals are more than 60 m (200 ft) thick. Conformably overlying the Favret formation is the Panther Canyon formation. This formation is 215 m (700 ft) thick and consists of a siliclastic and carbonate sequence of conglomerate, quartzite (sandstone), mudstone, limestone, and dolomite. It is a distinctly coarsening-upward sequence of rocks. The top of the unit is conglomerate with chert and quartzite clasts up to 150 mm-diam (6 in.-diam). The Augusta Mountain forma-

Jan 8, 1988