Search Documents

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By Nasri Munfah, Steffen Matthei, Vojtech Gall

"Conventional tunneling as defined by ITA WG19 is also known as the New Austrian Tunneling Method (NATM) or Sequential Excavation Method (SEM) was transformed in the US to deal with challenging tunneling conditions as an alternative to the more traditional tunneling methods. It is being used more often in urban areas, under difficult ground and ground water conditions, and with limited cover. Often the tunnel is of a large and non-uniform cross section in soft soils or weak rocks. The intent of using this tunneling method is to minimize impact on traffic and utilities and reduce disruption of everyday life of people and businesses. To meet these challenges, the industry developed technical approaches and implementation techniques and established sophisticated contractual relationships and collaboration in the field among various parties for successful implementation. This paper examines the development of conventional tunneling (NATM/SEM) in the US to deal with these challenges using recent examples such as Russia Wharf in Boston, Northern Boulevard Crossing, in New York, and Chinatown Station in San Francisco. INTRODUCTION / HISTORY Conventional tunneling or NATM/SEM is a concept that is based on the understanding of the behavior of the ground as it reacts to the creation of an underground opening. In its classic form the SEM/NATM attempts to mobilize the self-supporting capability of the ground to an optimum thus achieving economy in ground support. Initially formulated for application in rock tunneling in the early 1960’s, NATM has found application in soft ground in urban tunneling in the late 60’s and has since then enjoyed a broad, international utilization in both rural and urban settings. In the US the NATM/SEM tunneling method has been used successfully to address challenging tunneling conditions in urban areas. A large number of tunnels have been built around the world using a construction approach which was loosely termed NATM. During the years of discussions and the application of NATM a variety of terms have been used for the same construction approach. These terms were primarily aimed at describing the construction approach rather than the region of its reported origin."

Jan 1, 2016

By Marcel Laflamme, Sebastián Ibarra‑Gutiérrez

Improvement on controlling the stope limits has enabled the assessment of technical performance in several underground mining operations. Technical performance, integrated to stope geotechnical and geomorphological parameters, constitutes the basis which guides mining engineers in the Mineral Reserves Estimation process. Moreover, there are established definitions to report this information in Canada, incorporated in NI 43–101, which stipulates that “A Mineral Reserve includes diluting materials and allowances for losses that may occur when the material is mined” [1]. However, some loopholes have been identified regarding practical standards followed to specify the way to include and report ore losses when the lost material was blasted and must be left behind unrecovered inside the stope. In fact, general efforts to estimate and quantify the negative effects of operational ore losses only consider under-break ore loss. However, mining engineers frequently confront situations requesting the anticipated closure of a stope. Therefore, reconciliation process should reflect the amount of unrecovered Mineral Reserve. This work presents a discussion of possible practices to integrate adequately operational ore losses consisting of blasted but not recovered material and focuses on how different approaches regarding the material constitution could severely affect the stope technical performance interpretation.

Aug 9, 2021

By W. Lorenz

The responsible treatment of natural resources, including mineral raw materials, contributes to the protection of the environment. The management of resources and the environment encompasses reduction of emission through application of environmentally friendly processes, economical use of resources, recycling and substitution, application of energy saving processes, land reclamation and recultivation, as well as a well balanced regional and land use planning. A variety of materials are needed for measures to protect the environment. Many of these materials are, or to a large percentage consist of, mineral raw materials, which become effective either directly or indirectly in their natural state or after an appropriate industrial treatment. We call them environmental minerals. Although extraction and processing of these mineral raw materials destined for use in the protection of the environment, may have a negative impact on the environment on one hand, preventive or curing measures to protect the environment on the other would not be possible without them. We have to accept certain smaller burdens of the environment, which naturally will have to be kept at the lowest possible level, in order to avoid or minimize greater damages to nature. In the broad group of industrial minerals and rocks there is a wide variety of mineral raw materials, which lend themselves for countermeasures in favor of the environment. To hamper their production and processing through excessive environmental regulations would make the protection of the very environment more difficult or even impossible.

Jan 1, 1995

By Karl V. Lindell

Asbestos is not the name of a distinct mineral species, but rather the commercial term applied to the fibrous form of several minerals differing widely in composition. There are some 30 known varieties of asbestos but of this number only 6 are of economic importance, and these, in order of economic significance are chrysotile, crocidolite (or blue asbestos), amosite, anthophyllite, actinolite and tremolite. Chrysotile asbestos was formed by the introduction of hydrothermal solutions into fractures in serpentinised ultrabasic host rocks. These solutions dissolved magnesium silicate from the wall rocks, and with subsequent lower temperature and pressure they became supersaturated, and crystals of chrysotile asbestos formed. The chemical composition is variable but is classified as a hydrous magnesium silicate, containing a high percentage of magnesia and water, plus varying amounts of alumina and ferrous and ferric iron. Other asbestos minerals are formed by a similar process but with a different host rock e.g. crocidolite occurs only in iron' formation. The chemical composition of asbestos minerals other than chrysotile, shows a wide variation, but in general may be classified as silicates, or metasilicates, containing varying amounts of calcium, magnesium, sodium and iron.

Jan 1, 1964

By Immo H. Redeker, O. E. Pothier, E. W. Gieseke

Phosphate rock is the primary source of phosphorus, an element necessary to all forms of life--plant, animal, and human. While phosphorus finds many uses in everyday life, it is an irreplaceable ingredient in all complete plant foods. With the present need for intensive farming, the fertility of the soil can be maintained only by external additions supplied by mines or other sources. A major consideration in any mining operation is to establish the economic and ecological impact of the development on the local population as well as the national interest. The Commodity Data Summaries, as published by the U.S. Bureau of Mines (USBM), is a ready reference concerning the importance of phosphate to the national and local interest. The summary of domestic and world pro¬duction is given in Table 1. During 19722 the demand for marketable phosphate rock exceeded the supply in the United States and the rest of the world. Domestic and world reserves are more than adequate to meet furture demands. Phosphate rock prices firmed and export prices increased, reflecting the change from oversupply to a shortage of phosphatic fertilizers. Demand is expected to exceed supply through 1973. New fertilizer plant capacity planned for 1973-74 will increase the production of phosphate rock by more than 5 million tons in the United States. Morocco and Spanish Sahara are scheduled to increase their production to 18 and 3 million tpy, respectively, within 2 to 3 years. The domestic phosphate rock production for 1972 was 40.8 million tons and 1973 was 42.1 million tons.' Industry, with government-supported programs, will emphasize restoration of mined land and solution of the colloidal slime disposal problem in Florida. The foregoing information comes by courtesy of The Division of Nonmetallic Minerals of the U.S. Bureau of Mines, January 1973. The summary gives a great deal of information but does not give a complete picture. There are many supporting industries which contrib¬ute to the area in which the mines are located. The figures shown in Table 1 deal with concentrates. To produce such concentrates many more tons of waste overburden and ore must be moved. Because of the competitive nature of the phosphate rock industry, data on concentration ratios not only are difficult to obtain but also are not for publication by companies. The concentration ratios vary from one mine to the next in Florida as well as in Tennessee and the western United States. To produce 42.4 million tons of phos¬phate rock in the United States required moving about 350 to 400 million tons of material. Domestic Industry. In 1972 some 26 firms and the Tennessee Valley Authority produced phosphate rock, with several firms produc¬ing from more than one mine. The distribution of marketable phos¬phate rock production was: Florida and North Carolina 82%; Idaho, Montana, Utah, and Wyoming 13%; and Missouri and Tennessee 5%. The value of this production was $223 million. The principal consuming classifications were: agriculture 75%, soaps and detergents 5%, plating and polishing 3%, animal feed supplements 4%, and miscellaneous applications 13%. Over 5,000 firms processed end-prod¬ucts for agricultural purposes. Uses of Phosphate Rock. The tendency in the United States has been to produce more phosphoric acid by the wet process, while the production of electric furnace phosphorus, triple superphosphate, and ordinary superphosphate has been on the decline. Exports of phosphate rock have been on the increase for several years and in 1971 reached 33% of total production. However, export sales of phos¬phate rock are expected to decline in the years ahead, both in total tons of sales and in percentage of production as domestic sales increase (see Table 2). The description and chemistry involved in the production of phos¬phate fertilizers is too complicated to be presented here. The Waggaman13 book is a very thorough reference on the subject involv¬ing production, utilization, and chemistry. The various operations generally have chemical plants near the dry plants or ship to associated chemical plants for further processing. Wet rock, dry rock, and ground dry rock of various grades are sold. In addition various grades of calcined phosphate rock, including defluorinated phosphate rock for animal food supplements, are pro¬duced. Various grades of phosphoric acid, superphosphate, triple suerphosphate, as well as diammonium phosphate, are produced. These products are available from the various producing compa¬nies listed in the text. For prices and specifications the producing companies should be contacted.

Jan 1, 1985

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Michael E. Mcllwain, Lee O. Nelson, Robert D. Rogers, James H. Wolfram

Examination of the economics and environmental consequences associated with phosphate fertilizer production documents the necessity for development of innovative production technologies. Evidence of phosphate ore's susceptibility to microbial alteration indicates that it will be an ideal candidate for industrial-scale bioseparation. There are at least two applications for the biosolu- bilization technology: (1) an industrial-scale bio- process similar to the presently used wet acid process and (2) production of small prills (bio- bead) containing unprocessed rock phosphate and the biological ingredients necessary to promote phosphate solubilization. At the present stage of development, the biobead technology is the preferred application. It is an energy-efficient "green" technology that will dramatically reduce the amount of solid waste and air emissions produced by the phosphate industry.

Jan 1, 1999

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992

By Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980's. Approximately 50 million tons of hazardous wastes are produced yearly. One of the major aspects of the problem is the siting, design and construction of environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sires for several reasons: 1. Surface mines represent an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic savings when compared with sites on undisturbed lands chat might require extensive excavation or embankment construction.

Jan 1, 1981

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By R. L. Grayson

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition, and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1996

The structure of a mine ventilation network (M.V.N.) can be represented graphically using either the mine plan (map) itself or a number of other types of diagrams. In the U.S., the two most common approaches are the line and the schematic diagrams (see Figures 1 and 2). The purpose of this paper is to introduce another type of diagram, called the canonical diagram (6). The method of M.V.N. representation which uses canonical diagrams is used extensively in Europe, and especially in Poland, where it was developed. The canonical diagram is a noncalibrated topological image of a ventilation system. It gives a simple representation of the ventilation network, allows for the classification of currents within it and enables rapid computer analysis and computation, as well as the representation of the results. It is especially useful in studying and controlling the air flow, and it may be a life saving tool in conducting rescue operations during and after mine fires.

Jan 1, 1986