Search Documents

By Y. Luo

Although considerable progress has been made in the last decade in predicting surface subsidence over longwall panels, a number of important issues deserve further studies in order to improve the techniques and accuracy of subsidence predictions. Some of the problems are: (1) subsidence over the chain pillars between mined longwall panels; (2) subsidence development process after face stop due to either a vacation or the completion of a longwall panel; and (3) subsidence initiation and development process over the setup entry area in the initial stage of mining a longwall panel. In this paper, the measured data related to the targeted problems are presented, the data analysis techniques are briefly introduced, and some of the prediction methods developed based on the collected data are proposed. The proposed methods can be used as supplemental tools for the existing subsidence prediction models to improve their prediction accuracy.

Jan 1, 1991

By Y. J. Wang

This paper deals with the application of linear programming to the solution of mine ventilation network problems which involve only the controlled splitting of air. An airway whose air quantity is to be controlled to a prescribed value is called a "fixed-quantity" airway. In a network where the fixed-quantity airways are increased in number and are distributed such that the air quantities for the remaining airways are uniquely determined by Kirchhoff's first law, the problem reduces to determining the head losses and locations for air regulators and fans. This is one of the network problems encountered most often in underground coal mines. By formulating Kirchhoff's second law as a set of linear constraints and the total air horsepower supplied by fans as a linear objective function which is to be minimized, the problem is analyzed through the technique of linear programming. Some important properties of the problem are discussed and examples are presented.

Jan 1, 1971

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993

By A. P. Gentsch

Commercially mined calcium carbonate is normally found near the surface in the United States. It is nun& either by open pit or underground methods, depending upon its geologic setting. Processing ranges from simple crushing to the more sophisticated ultrafine processes. Intermediate steps are pulverizing, screening, beneficiation, classification, fine and ultrafine grinding, and surface treating. These processes are performed both dry and/or wet resulting in powdered or slurry end products.

Jan 1, 1986

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device. Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery. Recent developments-in electrooptic inspection of dry end wet material leaving a grinding device are critically reviewed. New methods for characterizing ultrafines are discussed. A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine index and other fineness indices is described.

Jan 1, 1983

By T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performances of various flowsheets. For a given flowsheet configuration, unit processes dimensions and operating conditions, the simulator calculates the steady-state values of the process variables. A supervisory algorithm is implemented in the simulator to determine the conditions which meet the required criterion on operation, tonnage and product quality. Calculation illustrations are proposed for the design of wet and dry grinding circuits. The performances of various arrangements of cement clinker and sulphide ore grinding flowsheets are evaluated and discussed.

Jan 1, 1983

By McCarthy. Richard E.

The prime movers of the Centralia Project, the surface coal mine and the power plant, private utilities are very aware of public attitudes. They have established and maintain the reputation for leadership in public service and are genuinely concerned that this project initiate the pro-grams and design the hardware to answer the question :What will be the impact of the mine and the plant on the physical environment, i.e., the air, soil and the water." So in the beginning almost as soon as the decision had been made to go ahead with the project, officials of the two private utilities, Washington Water Power and Pacific Power & Light went on record and publicly stated time and again that the overall approach of the Operators would be to do all that was reasonably possible to safeguard the environment. This attitude became part of the thinking of the project planners, part of the design of the power plant and part of the plan for the surface mine. The coal to be mined is from the Skookumchuck formation. The formation is Late Eocene and is made up of poorly consolidated marine and non-marine deposits. The major overburden removal equipment is a bucket-wheel excavator -conveyor system and a 56 yard dragline. Mining of the coal will be done with truck and shovel. The coal is processed, washed and crushed to 1 ¼ " for delivery to the power plant. The muddy water created by the washing process is chemically treated and the solids removed by a thickener-vacuum filter system.

Jan 1, 1971

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By Jack A. Simon

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which difEerentia1 movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas are affected by relatively minor vertical movements of the shoreline. The large plates have continually or intermittently moved throughout the geologic past, resulting in various configurations of the continents and oceans, and coal-forming conditions have occurred at numerous times and places. Vast areas of our continents have been repeatedly inundated by shallow oceans and only relatively small parts of the present continents appear to have been above sea level throughout geologic time. Great forces acting principally along plate margins have folded and broken the crustal rocks, forming large belts of mountains.

Jan 1, 1981

By John Carr

The tremendous growth in grinding mill size and horsepower during the '70s demanded advancements in gear cutting technology and equipment for the '80s. Computers are used as an aid in the design and selection of the mill drive system; sophisticated computer graphics are used to create manufacturing drawings; and a new generation of gear cutting machines are used to manufacture the gears. These new gear cutters can generate-cut gears over 40' (12.2 m) in diameter at an AGMA quality level exceeding the currenty acceptable standards. The precision of the resulting gear assures maximum tooth contact, which will result in longer gear set life.

Jan 1, 1981

By Gregg J. Hodges

The Stillwater Mining Company, a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corporation, began commercial production of flotation concentrates from the western hemispheres' only primary platinum palladium deposit at Nye, Montana in March 1937. In the fall of 1987 an integrated pilot plant testing campaign of electric furnace smelling and oxygen? blown converting confirmed the feasibility of further upgrading to semi? refined matte or 'white metal". In the summer of 1990 the production smelter was brought on-line at Columbus, Montana. This paper describes the technology transfer from the pilot to the production smelter. Emphasis is placed on flowsheet development and the scale factors between the test and production furnaces and gas cleaning plants. The metallurgical results of the pilot plant and of the early months of production of the commercial works are also compared.

Jan 1, 1991

By C. T. Aimone-Martin

Time-domain reflectometry (TDR) laboratory experiments have been conducted using cylindrical salt cores from the Waste Isolation Pilot Project (WIPP). TDR has been used as an instrumentation technique to quantify the type and magnitude of rock mass deformation. Laboratory shear and tensile tests were conducted to calibrate measured deformation versus changes in reflected waveforms. Coaxial cables grouted within rock cores were crimped to produce localized reference defects. The evaluation of waveform characteristics produced during rock deformation experiments shows a good correlation of cable response to both shear and extension of the salt

Jan 1, 1994

By J. A. Herbst, H. R. Cooper, R. J. Brison, R. W. Harper, K. P. Ananthapadmanabhan, W. C. Hellyer, B. H. Bergstorm, D. M. Hopstock, H. Rush Spedden, W. C. Hellyner

Scope of Section The physical characterization of an ore or mineral mixture in such detail that mineral processing may be effectively applied to create more useful products is one part of the technology of sampling and testing. In addition, the evaluation of the multitude of separation processes, both physical and chemical, combined with ancillary opera¬tions and performed on samples at a laboratory scale, is another part of the testing procedure. Although analytical techniques provid¬ing quantitative determinations of elemental compositions are an im¬portant and necessary supplement to any testing program, that field of endeavor is a well-developed, separate entity beyond the scope of this Section. Sampling procedures cover the practice of selecting representative quantities of test materials in the field to evaluate mineral deposits, and extend to techniques of obtaining process samples in slurry and bulk ore as part of process evaluation. The same techniques are appli¬cable, of course, to standardized methods of metallurgical accounting. Sampling is also an important facet of successful on-line measurement of slurry properties such as assays and particle size in the practice of automation. However, the sampling methods in this case can be different from those needed for precise testing and accounting pur¬poses. Sampling was well defined in Taggart's Handbook as "the opera¬tion of removing a part convenient in size for testing, from a whole which is of much greater bulk, in such a way that the proportion and distribution of the quality to be tested (e.g., specific gravity, metal content, recoverability) are the same in both the whole and the part removed (SAMPLE). The conditions of the more stringent definition, that the sample shall be completely representative of the whole as regards all aspects save bulk, are practically never fulfilled when heterogenous mineral mixtures are sampled." Taggart's Handbook of Mineral Dressing, Section 19, "Sampling and Testing," continues to be a very useful compendium of principles and techniques, particularly as applied to manual methods for han¬dling samples. In the intervening years since its last revision, substan¬tial progress has been made in both the theory and the techniques; thus, this current contribution is designed to be an extension of the earlier work, yet complete enough to provide procedural guidelines to methods of continuing validity. Although basic principles of testing remain unchanged, the meth¬ods of applying those principles have undergone great change. New testing equipment has become available, yielding a greater precision of results. Testing methods have been refined which, in many cases, allows for a valid scale up of flowsheet designs without the necessity of costly pilot or prototype plant development. Justification for a Sampling and Testing Program* The proper evaluation of a mineral property is a complicated process. It often is done on a team basis with the exploration geologist, mining engineer, mineral process engineer (extractive metallurgist), economist, and product utilizer (ceramist, chemical engineer, chemist, metallurgist, etc.) all represented. The mineral processing engineer is a key member because he can provide a go no-go answer to the question, "Can this ore be processed economically?" In addition, his judgment on the response of even the initial sample to processing can be an invaluable guide to the proposed process and its mutations. Since the capital investment and operating costs are so sensitive to the type of process used, the judgment of the mineral processing engineer forms an important part of the early evaluation of the profitability of a new mining venture. This early estimation of the processing approach is all the more important since, for some metalliferous ores, the capital investment for mill, smelter, water supply, and tailings disposal exceeds the cost of the mine. At present, for commodities such as coal, the reverse is true. There is a smaller capital investment for the coal preparation plant than for the mine. In general, both the capital and operating costs escalate very rapidly in the following order: gravity concentration of alluvial deposits (e.g., dredging), gravity concentration of lode ores, flotation, simple hydrometallurgical processes, and complicated hydrometallurgical and pyrometallurgical processes. The latter two processes may cost 100 to 1,000 times more per ton treated than processing of a simple alluvial deposit. This dictates that the valuable mineral be concentrated as much as possible to minimize the total tonnage treated in the more expensive operations. Within each of these ore-processing categories there is a wide range of process sophistication and hence of capital and operating costs. Perhaps the greatest variations are in the chemical processing of ores. These range from the simple leaching of a copper waste dump to very sophisticated hydrometallurgical processing of ores in increasing order of cost. Because the overall cost of a mining venture is so sensitive to the process selected, it is essential that the mineral¬ processing engineer evaluate the ore in the initial stages of the development of an ore body. As better samples become available, he must continually revise his estimate of the process to be employed. The sampling and testing process must be a necessary and continuing activity throughout the life of a project. One fundamental aspect of nearly all mineral deposits is the inherent variability of the mineral assemblage and composition. A utopian goal of any processing plant is to have the process so flexible and so well-defined that an automatic process control system can optimize the economic recovery at all times. Since this is rarely possible, a continuing or at least a periodic testing program is desirable. Variables to be considered are: 1) Ore body inconsistencies. 2) Zonal variations. 3) Feed variations from mining plan or methods. 4) Variable performance of processing units due to wear. 5) Seasonal or other changes affecting processing conditions such as water quality, temperature, etc. 6) Changing market conditions for product quality or byproducts. 7) Technological advances in processing methods or equipment. 8) Increasing demands for environmental control. 9) Changing economics of competitive processes, of supplies, of capital investment vs. labor costs, etc. Sampling Procedures Preliminary Guidelines for Sampling Ore Deposit Studies. t At a very early stage, it is essential that the mineral processing engineer receive a sample of the ore. This may be a portion of the diamond drill core or a split from the trench, pit, churn drill, channel, or sheet sample. Even a grab sample may have some value, but it should be selected by the mining engineer or exploration geologist to be as representative of the ore body as possible within his best judgment. The sample delivered to the process engineer should have been subjected to as little prior crushing as is practical since fine sizes are difficult to concentrate. In addition, finely ground ores are readily oxidized and thus may give misleading test results. Furthermore, ground samples may make it impossible to eval¬uate either the comminution or the coarse-gravity concentration pro¬cesses. For an initial evaluation, a good deal may often be learned from a sample of only a few pounds if that is all that is available. To obtain the maximum information from a sample, its selection should be carefully discussed with the mineral processing engineer. In addi¬tion to being as representative as possible, the mineralogically distinct samples should be carefully segregated rather than composited. Since drastically different processes are often needed to process samples of differing mineralogy, considerable care and time must be exercised during this sample collection step. The segregation of samples showing gross mineralogical differences, such as the oxide caping on a sulfide deposit or a laterized zone, is easy. It is the more subtle changes in mineralogy that can often elude the field man. Yet these differences are often sufficient to dictate that an entirely different type of process be used. Obviously, the selection of these initial samples for ore testing and mineralogical studies requires that it be done by a man of consider¬able experience and judgment. While the mining engineer or field geologist is collecting these samples, he should also note and convey to the processing engineer such details as water quality and availabil¬ity, terrain, potential mill location, tailings-disposal areas, case of transportation, etc. As the property is developed with additional drill holes, adits, etc., larger and more representative samples will be required to develop the ore-processing flowsheet more adequately. If pilot-plant studies are required, a very large sample may be necessary. Though the type and amount of sample collected for flowsheet development investigations vary widely, gathering a representative sample of the ore body is a prime requisite for any process development effort. The process developed for any given ore body is only as reliable as the sample on which the flowsheet was based¬

Jan 1, 1985

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009