Search Documents

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By B. Hornsby

At the Mount Isa mine, Mount Isa, Qld., Australia, sublevel open-stope mining is used for copper ore while both sublevel open-stope and cut-and-fill methods are used for the silver-lead-zinc ores. Production in 1979¬80 was 4 730 000 t (5,200,000 st) copper ore and 2 590 000 t (2,850,000 st) of lead ore. The deepest mine level currently is 960 m below the surface. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The mine is located in the valley of the Leichhardt River in Lower Proterozoic sediments of the Mount Isa group. The regional strike of the sediments is north¬south and they have a persistent westerly dip of about 1.1 rad (65°). In the mine area, the Mount Isa group comprises a sequence of alternating bands of dolomitic shales and siltstones some 3.2 km (2 miles) in width. It is bounded on the east by greenstones and quartzose sediments of the Eastern Creek volcanics, and on the west by the Mount Isa fault, west of which occur schists and other metamorphic rocks. The ore bodies as currently known at Mount Isa are restricted to the Urquhart shale, a formation of thinly bedded pyritic, dolomitic, and volcanic shales some 1070 m (3500 ft) thick. Towards the top of the Mount Isa group sediments, copper and silver-lead-zinc ore bod¬ies occur as contiguous but discrete entities and are mined and treated separately (see Figs. I and 2). Argentiferous galena, sphalerite, pyrite, and minor associated sulfides occur in distinct concordant bands throughout the Urquhart shales. Wherever these bands are grouped together in sufficient density they constitute silver-lead-zinc ore bodies with widths varying up to 36.6 m (120 ft). Other mineralized bands are common in intervening beds. Individual ore bodies persist for many hundreds of meters concordant with the strike and dip of the enclosing shales. Intersections of these beds with fold axes provide local zones of enrichment but otherwise the mineral content of the ore bodies varies only slightly throughout the extent of the dip and strike. Chalcopyrite is the only important primary copper mineral. It occurs in association with pyrite and pyrrhotite as disseminated flocks and as vein fillings throughout irregularly shaped zones of folded, brecciated, and re¬crystallized Urquhart shale. These zones, which are lo¬cally termed "silica-dolomite" bodies, are broadly transgressive to the shale bedding and confine all significant copper mineralization to the virtual exclusion of silver¬lead-zinc mineralization. In some areas, the downward percolation of acidic water through faults and shears has caused extensive leaching of the coarse-grained carbon¬ates to depths in excess of 610 m (2000 ft), but most of the silica-dolomite remains unleached and the ground is competent. The majority of lead ore being mined is north of the main shaft pillar (R62, U62) area. The major lead¬producing areas for many years have been the Black Star ore bodies (2 and 5 ore bodies) and the Racecourse ore

Jan 1, 1982

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

By M. J. Hart

Today, aggregate producers in the Denver Metropolitan area, herein defined as Denver and surrounding communities in Adams, Arapahoe, Boulder, Douglas and Jefferson Counties, are scrambling to secure their future reserves. The Denver market is somewhat unique among the larger metropolitan markets in that the source of needed aggregate for the future is very much undecided. 2. Present Aggregate Resources Presently, the annual consumption of aggregate resources in the Denver Metropolitan area amounts to approximately 16 million tons of sand, gravel and crushed stone of which the later accounts for about 20%. Based on population growth projections for the front range, by the year 2000 the annual rate of consumption for aggregate in the Denver Metro area could be in the 25+ million ton range.

Jan 1, 1987

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978

By C. L. Glorioso

As an introduction and credentials for our talk, let me take a moment to introduce you to Wimpey Worldwide and specifically to Wimpey Minerals, USA, Inc.

Jan 1, 1995

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

By Gordon J. Hughes

The ldaho Cobalt Belt represents a unique geologic environment containing some of the largest known reserves of cobalt in the United States. Stratabound cobalt-copper-gold deposits formed within a sedimentary basin that was generated by the rifting of an Archean cratonic block. Host rocks for these deposits are the Early to Middle Proterozoic Yellowjacket Formation comprising a suite of clastic sediments, volcaniclastics, and mafic tuffs that accumulated in the intracratonic rift basin about 1.7 b.y. ago. Rifting was probably initiated during a regional heating and doming event that may date back to 1.8 b.y. ago. During this time, other rift basins were likely to have formed in the region. They probably represent the precursors of a much larger depositional environment having characteristics of an Atlantic- type or passive continental margin where younger formations of the Belt Supergroup were deposited. The Yellowjacket Formation has been subdivided in the Idaho Cobalt Belt into three genetic units representing various subenvironments of a deepwater clastic fan complex. A northwest- trending deep-basin structural trough accumulated fine-grained muddy sediments that were periodically interrupted by distal turbidites of the subaqueous fans. Subsequent progradation caused the deposition of coarser-grained clastics of the more proximal portions of the fan complexes. Submarine fan lobes were built across northwest-trending tectonically active basin growth faults. These in-basin structures caused a great deal of penecontemporaneous deformation within the Yellowjacket sequence. Northeast-trending fault zones formed an orthogonal set of fractures that controlled the shape and size of sub-basins, and were also an influence on lateral migration of dominantly fine-grained clastic material. The eruption of mafic tuffs at about 1.7 b.y. ago added a new component to the Yellowjacket sedimentary sequence. Around the Blackbird mine area these tuffs commonly occur either near the base or within some of the sandier sequences. Since most of the sand influxes were largely controlled by basinal tectonism, the tuffs were probably erupted during tectonically active periods of basin development. The dynamic nature of the sedimentary environment probably caused much of the tuffaceous component to be mixed with other clastics and even resedimented as volcaniclastic material. In time, the change to a higher energy sedimentation regime resulted in such a dramatic clastic dilution of the tuffs that they could not survive in the areas of the vents, and, if present, they must have been distributed elsewhere in the basin.

Jan 1, 2013

By A. Unal

Barbaro et al. (1990) implemented a tedious study aimed at delineating the short-scale spatial variability of sulfur in a coal seam. It is not possible, however, to extend their conclusions to any other coal seam or use theirs in any other fashion, because the background geology was not presented. Nor were the conclusions accompanied by geological interpretations in the paper. In addition, an unfortunate printing error occurred where the total sulfur (determined by High Temperature Combustion) variogram in Fig.3 was duplicated in Fig. 2 instead of the seam height variogram. A more serious error, however, has been committed in the definition of the variable, seam height. What is defined as seam height by Barbaro et al. (1990) is, in essence, mining height, and is not a regionalized variable that should be studied by geostatistical methods directly. Despite the fact that the variable, seam height, is not defined in the paper explicitly, the following quotation discloses the fallacy: "All roof rock that exceeded 1.8 m (6 ft) from the floor was not taken because the longwall was operated to not mine more than 1.8 m (6 ft) unless the coal seam height exceeded 1.8 m (6 ft)." From this definition, the seam height, and therefore the sampling height, is equal to the actual coal thickness, if the coal thickness is greater than 1.8 m (6 ft). Otherwise, it is equal to the sum of the coal thickness plus the thickness of the roof rock that complements the thickness to 1.8 m (6 ft). In the latter case, the seam height is constant and equal to 1.8 m (6 ft). It is possible to conduct a variogram study on a pool of samples that are realizations of two different variables. But the conclusions derived would not belong to any one of the two variables uniquely and, therefore, do not possess any significance. Geostatistical analysis is irrelevant for the sum of multiple regionalized variables formed by arbitrary selections. In a two¬seam setting, for example, the mining height, as defined by the thickness of one seam at one location and the thickness of both seams at another location (due to quality and/or minimum thickness considerations perhaps), should not be used in the calculation of one common variogram. The two seams should be modeled separately. They can then be combined according to the specific purposes of the study. On the other hand, if a constant is added to a regionalized variable (to incorporate dilution perhaps), the variogram of the new variable will not change. Barbaro et al.( 1990), surprisingly, does not give any geologi¬cal interpretation of their results despite the fact that most of them can be explained by the origins of sulfur in a coal seam. The presentation of the results of a geostatistical study with no reference to the geology of the deposit is uninformative. It may also be misleading for the potential users of geostatistics. It is not unusual to find nuggets of pyrite in coal seams. In such cases, pyritic sulfur will probably display a spatial structure for only a very small distance that will appear in the experimen-

Jan 1, 1991

By Douglas W. Barr

Water is a necessary part of our environment. It is a biological necessity, but more than that, it is a necessary part of our life style. Those of us who live in the north woods expect water to be part of the scene. There are few natives of this region who would be content to eliminate the streams, the lakes, the marshes, or our forests. Throughout the world, water has been so much a part of man's environment and man's adaptation to life has been so closely tied to water that our way of life and ways of accomplishing our work include water as an essential tool. The production of taconite is an example of our dependence on water. Other methods could have been developed to process taconite ore but the process methods chosen utilize water. Water is used for grinding and separation and for trans- porting the ore from one part of the process to another and for dust control. A typical large plant producing 10 million tons of taconite pellets per year will have on the order of 130,000 gallons per minute (8.202 m 3/51 of water in circulation in the plant. About 120,000 gal. per min. (7.571 m 31s) will pass to tailing thickeners where 110,000 gal. per min. (6.940 m 31s) is separated from tailing and returned to the process. About 15,000 gal. per min. (.9464 m 31s) goes with thickened tailing to tailing basin. My point is that there are great volumes of water in motion in a taconite plant,

Jan 1, 1980

By Leo Gentile, David Selhorst

The $528 million Toledo Waterways Initiative (TWI) was implemented by the City of Toledo in 2002 and completed in August 2020. Toledo is one of many US cities required to implement a Long-Term Control Plan (LTCP) but one of few to have completed its plan. TWI consists of three storage and conveyance tunnels, four below grade storage basins ranging from 4 to 36 million gallons (MG), miles of sewer separation and interceptor improvements, green infrastructure and other appurtenant structures to dramatically reduce combined sewer overflows to the Maumee River, Ottawa River and Swan Creek. All three rivers flow into Lake Erie. The City’s 180-year history as a Midwest shipping, manufacturing and transportation hub provided design engineers and contractors no shortage of unknown underground challenges to complete the projects. The City will begin its 5-year Post-Construction Compliance Monitoring in 2021 to satisfy the final LTCP requirement. A program overview and experience from tunnel and underground basin construction in urban areas with buried active and legacy infrastructure will be discussed.

Jun 13, 2021

By Evan Brinkerhoff, Steve Chorley

The largest hard rock TBM ever to bore in the USA, an 11.6 m diameter Robbins Main Beam TBM, recently underwent a planned in-tunnel diameter change to a more compact 9.9 meters. The first-of-itskind conversion process for the Main Beam TBM was undertaken 2.8 km into the bore and was not done inside a shaft or pre-excavated portal. This paper will detail the unique dual-diameter machine designed for the Mill Creek Drainage Relief Tunnel in Dallas, Texas, USA, machine performance, and successful size conversion process that took place in early 2021—a process that utilized the four C’s of construction to enormous benefit: Communication, Cooperation, Collaboration and Coordination.

Dec 1, 2022

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design, and operation can be utilized in underground mines from ground movement data. Communicating the information and exploring new findings can be a challenge in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as it is multidimensional, depending on the space and the rate it takes place. To tackle this challenge, geotechnical engineers should focus on utilizing simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a Trigger Action and Response Plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study is conducted at the San Xavier (SX) Underground Mine Laboratory’s East decline. The project aims to produce visualizations that optimize the use of geotechnical data in near-real-time.

Feb 1, 2025

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By Julia Herhold

The demand for sustainable and profitable/efficient projects within the tunneling and other underground engineering sectors grows rapidly. Construction tasks play a key role within the project conduction, whether as primary (tunneling), secondary (e.g., mine securing) or tertiary processes (e.g., workshops). The construction tasks of primary processes create the main structures, such as tunnels, which resemble the main project goal. For the secondary and tertiary processes, the purpose of the task shifts. The main goal is to provide structures, such as the securing of the cavity and workshops, that enable the project and enhance the efficiency of the primary conduction underground. To plan and optimize the conduction of construction tasks underground, whether they are identified as primary, secondary or tertiary tasks, the work preparation can be used. This method, known from the above ground construction, can be adapted and used underground. The approach of a digital work preparation tool combines, connects and adapts the main tasks “choice of procedure,” “logistics” and “site planning.” In addition, the digital tool is connected with digital models (construction, site, surroundings). With the adaption and forward projection of the work preparation, underground constructions (e.g., tunneling) can provide a more sustainable and efficient outcome.

Jun 13, 2023