Search Documents

By Eero Pokki

The Päijänne Tunnel is being constructed to conduct raw water from Lake Päijänne to the Helsinki Metropolitan Area. The length of the tunnel will be 120 km and the cross-sectional area is 15.5 sq m. Excavation started in 1973 and will be completed in 1982. 94 km of the tunnel have been constructed from Lake Päijänne towards Helsinki. The construction has advanced according to plan, and due to Finland's hard bedrock there have not been any great surprises. When completed, the tunnel will meet the water requirements of the Helsinki Metropolitan Area for a long time in the future because, with a free fall of 36 m, 9.6 cu m/s of water can be conducted through the tunnel from Lake Päijänne to the Helsinki Area. With pumping it will be possible to obtain a flow of 15 cu m/s, although at first the discharge will only be 5 cu m/s. The tunnel was partly taken into service as early as March 1979 when it was possible to conduct water to the municipalities north of the Helsinki Area. It is already possible now to conduct water to Helsinki, too, but from the Korpimäki pumping station onwards it must be done through the River Vantaa, which is polluted. When the tunnel is completed in 1982, good quality water can be conducted from Lake Päijänne to the Helsinki Metropolitan Area through a continuous rock tunnel. The cost estimate in 1973 was $ 88 million while it is now $ 90 million notwithstanding high inflation. AREAS NEEDED FOR CONSTRUCTION The areas needed for construction were bought through voluntary deals. Areas of 4 - 5 hectares were bought along the tunnel line at about 5 km intervals. The excavation of access tunnels was started from these places, and the crushed rock from the main tunnel was also transported there. However, it was not necessary to buy the area

Jan 1, 1979

By Alejandro Sanz Garrote, Juergen Laubbichler, Fernando Triana Gracian, Paz Navarro Gancedo-Rodriguez, Andreas Feiersinger

The Combined Sewage Storage Tunnel (CSST) is part of the Ottawa River Action Plan and will greatly reduce the frequency of sewage overflows into the Ottawa River during storms. The project consists of the design and construction of two TBM tunnels running EastWest (EWT) and NorthSouth (NST) along 6.2 km in total, and multiple shafts and support buildings. Contractor Dragados Tomlinson JV (DTJV) was awarded the 169 million CAD construction contract in 2016 and the CSST will be in operation in 2020. Dr. Sauer & Partners (DSP), supported by Intecsa-Inarsa, was responsible for the detailed design of the precast concrete tunnel lining as well as the geotechnical risk management program. This paper addresses TBM selection, critical tunnel sections, geotechnical risk management and rock mass grouting as a geotechnical risk mitigation measure. Successful collaboration of Owner, Owner’s Engineer, Contractor and Contractor’s Engineer led to a safe and cost-effective design and construction

Jun 13, 2021

By Cengiz Karagüzel, Ömer Canıeren

The mobility of gold and silver metals from refractory ores is very low due to free metal ions in their bodies that bind the transportable and free metal molecules or they are encapsulated in minerals such as sulfides, arsenosulfides, carbonaceous, and clayey materials which make it difficult to extract them. As known from the literature, the enrichment of oxide refractory gold, silver ores, Ag, and Au-rich flotation concentrated from sulfur refractory ores can be leached in the chloride-hypochlorite solutions. In this work, the leaching approach was studied to extract silver ions from refractory ores in the presence of hypochlorite media under high pressure. The mineralogical and scanning electron microscopy analysis of the sample indicated that the silver was encapsulated in barite and quartz minerals in fine sizes. In order to obtain the optimum leaching conditions for the silver ore, the effects of several parameters, namely, temperature, leaching time, NaCl and NaOCl concentration, solid ratio, and particle size on the leaching recovery were investigated in detail. The leaching experiments showed that the highest silver recovery of 62.35% was obtained under the following conditions: temperature of 150 °C, oxygen pressure of 1800 kPa, leaching time of 2 h, concentrations of 2 mol/dm3 and 0.4 mol/dm3 for NaCl and NaOCl, respectively, the solid ratio of 30%, and particle size (d80) 15 μm. The results obtained from this study indicated that the enrichment of refractory silver ores to extract the silver encapsulated in barite and quartz minerals could be possible in the chlorite-hypochlorite under high pressure, a relatively shorter leaching time compared to conventional cyanide leaching.

Jan 28, 2021

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

Energold Drilling Corp. is a leading specialty drilling company servicing the mineral and energy sectors in the Americas, Africa and Asia. Energold specializes in mineral exploration in remote locations with limited infrastructure. Such locations require the smallest footprint possible going in, leaving as little or no evidence on their way out. Energold?s rigs can be transported by helicopter or manually on footpaths as narrow as 1 m (3.3 ft). They set up quickly and then are struck and packed out, with any sign of their presence quickly disappearing behind them. Energold has teamed up with Atlas Copco and its team of engineers in North Bay, Ontario to design small rigs capable of drilling to a variety of depths, as required for each project.

Jan 1, 2013

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By P. F. R. Altounyan, I. W. Farmer

Groundwater freezing was used to stabilise 8m thick beds of saturated and weakly cemented sands at a depth of 170m, during driving of twin 1 in 4,5.2m o.d. circular drifts from the surface to the Coal Measures through 600m of Permo-Triassic strata. Instrumentation was installed during erection of the lining in frozen and unfrozen ground to measure ground and groundwater pressures on the lining and ground temperatures up to lm into the frozen ground. Observations showed that following thawing, effective lining stresses in the frozen zone were low, indicating minimum strata disturbance during freezing and subsequent machine excavation. Groundwater pressures were lower than expected.

Jan 1, 1981

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By A. T. Yu

Two major events highlight recent developments in US ore and coal ports: completion of the last series of modern taconite pellet transshipment facilities on the Great Lakes; and modernization and construction of coal ports, particularly on the East and Gulf Coasts. The New Taconite Transportation System To reduce raw material transportation costs, a fleet of new generation high-capacity 304-m (1,000-ft) self-unloading vessels were built to carry iron ore pellets from the Minnesota-Michigan iron ranges to the steel plants on the lower Great Lakes. Existing port facilities had to be modernized, revised, or completely rebuilt to accommodate these large vessels. Some of these were Burlington Northern's Allouez, WI, loading dock; Duluth, Missabe & Iron Range Railway Co.'s Two Harbors, MN, facility; Republic Steel's Lorain, OH, facility; and Chessie's Toledo, OH, dock. Allouez and Two Harbors receive taconite pellets from unit trains and load them onto large vessels either after dumping or via a large stockpile and reclaim system. The Lorain facility receives iron ore pellets from self-unloading vessels' discharge boom conveyor and reloads the pellets into rail cars or small vessels destined to inland steel mills. The Toledo facility receives Armco pellets from vessels, stockpiles them through the winter, and reloads into unit trains destined for Armco's mills along Chessie's rail tracks. Burlington Northern's $75-million Allouez pellet dock, completed in June 1977, was built to receive pellets produced by Hibbing Taconite Co. and National Pellet Plant in Minnesota, stockpile them through the winter when the lakes are frozen, and load them into 304-m (1,000-ft) vessels in the shipping season. As much as 10 Mt (11 million st) of pellets may be stockpiled within the loop track. A 6-km (4-mile) long conveyor system connects the stockpile area and the dock. Thirty-six new concrete silos were built on the dock to house 2 kt (2,000 st) each of pellets before shiploading. The $35.5-million expansion of the Two Harbors transshipment facilities began shiploading in July 1978 after ground breaking in Aug. 1974. Particularly noteworthy is the first application of the Orboom system-a breakthrough in technology for the modernization of the century-old pocket docks on the Great Lakes to accommodate the new generation of super vessels. The pocket-type loading dock has been a standard on the lakes for nearly a hundred years. Bottom-dump rail cars fill the ore pockets on top of a finger pier. Gravity chutes matching standardized ore ship hatch spacings are lowered to fill the holds of a 20.3-kt (20,000-dwt) ship. The construction is simple and the loading swift. In spite of advances in technology elsewhere, most of these docks continue to serve the iron ore and coal trade in the same manner they did in the 19th century. Although performance of the pocket docks on small vessels remains outstanding, the new 304-m (1,000-ft) vessels are beyond the reach of the old docks. After extensive development, the Orboom system (Patent No. 4,065,002) for pocket docks was successfully developed. The heart of the Orboom system is the retractable shuttle loading arm which loads the wide beam vessels. The Orboom shuttles are fed by existing pockets of the dock that, in turn, are charged by a tripper conveyor along the length of the dock. The Two Harbors shiploading system is supported by a 0.9 Mt (1 million st) storage-reclaim network. Unit trains are bottom dumped. Taconite pellets are stacked and reclaimed by bucket wheel reclaiming systems. Lower Lakes New Ore Ports At the lower Great Lakes receiv-

Jan 10, 1982

By Alix Thierart, Yann Rouillard, Bernard Catalano

Bessac's presence in Singapore started in 2014 with the construction of the Thomson metro line, which includes 18 miles of twin-bore tunnels and 22 stations split into 17 construction packages. Bessac joint venture was allotted the T219 lot. The works include the construction of a new 660-foot (200-meter) long transfer station, two parallel 19-foot (5.8 m) ID tunnels and a pedestrian underpass. The urban context and the very soft ground stratum imposed to utilize unusual tunneling techniques, from upgrading a slurry TBM to a high-density slurry TBM to launch with very low cover and canopy pipe roofing completed with a MTBM without retrieval shaft.

Jun 23, 2024

By James R. Brown

Mount Isa Mine should be regarded as a large mining complex rather than one mine. This arises from the geography, variety and extent of the orebodies, the mining methods, and the use of 14 shafts for ventilation distribution. A brief resume is presented here since comprehensive descriptions of lead-zinc mining methods {11}, copper mining methods {2 }{3}, geology 241, stope fill {5} and ventilation techniques {6}{7}, have all been published in the last five years. Mining extends over a north-south strike length of 2.5 miles (4 Ian) with a maximum width across dip approaching 3 200 ft (1 Ian). Current mining is to a depth of 3 150 ft (960 m) with the ore hoisting shafts extending 660 ft (200 m) deeper. The composite longitudinal section, Figure 1, shows a representational disposition of the copper and lead-zinc-silver orebodies in the central shaft complex where the main service and hoisting shafts are located. To the south the X41 man and materials shaft provides access to the copper area. The mine layout is typical of high tonnage track- less mines, utilising a large diesel fleet, raise- borers and some large diameter hole stope drilling. Mining methods include sublevel open stoping, slot and massfire, and a trial vertical crater retreat in the copper ore, and sublevel caving, sublevel open stopes with and without rib pillar recovery, and mechanised cut and fill in the numerous lead orebodies. All ore reports to one of the three crushing systems located below 19 level in the central shaft complex. Copper ore is hauled exclusively along the 19 level computer assisted Rockflo haulage system, and lead-zinc-silver ores report via central orepasses from Granby haulages on 13 level and 15 level. Tonnages hoisted during the 1977178 financial year were 5.0 million for copper at 3.2%. and 2.3 million for lead-zinc-silver at 7.8%. 6.3% and 7.06 oz/ton (216 g/tonne) respectively.

Jan 1, 1980

By Neil Williams

The brecciated dolostone-hosted (Mississippi Valley-type) and associated shale-hosted stratiform Pb-Zn deposits at McArthur River occur adjacent to a major syndepositional fault, the Emu fault. Base-metal zoning, mineral parageneses, and Pb and stable isotope ratios indicate that both types of deposits formed contemporaneously from metalliferous brines that flowed into the host sediments from the Emu fault. Derivation of brines from underlying evaporitic sediments is suggested. Geochemical evidence indicates that the mechanism of ore formation was sulfate-reduction coupled with oxidation of organic matter. The textural relationships of stratiform sulfide mineralization to diagenetic dolomite concretions, chert blebs, volcanic glass shards, and inter-ore breccia beds, indicate that the reactions proceeded diagenetically within about 100 m of the sediment/water interface.

Jan 1, 1979

By K. H. Nimerick

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.SoC (O°F). Other areas where FCA has found utility has been de-icing conveyor belts, idler, idler arms and other moving parts that have been impeded by ice.

Jan 1, 1977

By V. Aghazadeh, E. Bidari, M. Aazami

In this study, mineralogical and microanalysis characterization, as well as diagnostic leaching and cyanidation tests, were performed to gain a better understanding of the refractory nature of the arsenical zone of a Carlin-type gold deposit and also to evaluate possible treatment routes to maximize gold recovery. The results obtained showed that only 56% of the ore’s gold content is amenable to direct cyanidation. The majority of the remaining gold was found as submicroscopic gold and in association with sulfide minerals, such as orpiment, pyrite, and sphalerite. It was also found that despite the abundance of silicate and carbonate minerals in the arsenical zone, they do not play a key role in the refractory nature of the ore, and gold can be liberated from such minerals by appropriate grinding. The analyses further revealed that orpiment dissolves readily during cyanidation, and this dissolution retards the kinetics of gold extraction. Pyrite and sphalerite were generally found to occur in fine network texture and in association with quartz. Flotation of such auriferous sulfides may be difficult due to their oxidized surface. Fine grinding (−20 μm) was found to be partially effective in improving gold extraction.

May 28, 2020

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994

By D. D. Gertenbach

"The successful commercialization of a pressure oxidation (POX) process for recovering metal values, including gold, copper, zinc, nickel and molybdenum, is the result of a carefully planned development program. The initial task involves developing one or more conceptual flowsheets, including the POX autoclave and downstream purification and recovery steps. A laboratory program is completed to determine the technical viability of the flowsheets, define the operating parameters for each step and provide information for an initial economic assessment of the process. The process is then confirmed during a continuous pilot plant program, providing engineering design data and other information for the commercial design. A well-thought-out development program has been shown to be critical for reducing the risk of commercializing POX processes. Experiences developing POX processes for refractory gold ores and copper concentrates are briefly discussed. IntroductionPressure oxidation (POX) has become a common commercial operation for processing sulfide-bearing feedstocks. These feedstocks include gold ores and concentrates; copper concentrates; nickel concentrates and mattes; zinc concentrates; and molybdenum concentrates. Drivers for the development and commercialization of POX processes include:• The high cost for pyrometallurgical processing of sulfide ores, much of which is attributed to environmental controls.• The motivation to implement safe and more environmentally attractive alternatives for sulfide ores.• The need to process increasingly difficult ores with complex mineralogy.• Improvements made over the last 25 years in POX equipment design and experience operating commercial POX plants.Although the capital and operating costs for commercial POX processing can be high, this technology is capable of rapid oxidation of most sulfides and arsenic minerals in the feed, with little noxious gases and environmentally stable iron arsenate and other iron compounds in the POX residue (Marsden and House, 2006).In POX operations, sulfides are oxidized to either sulfates or elemental sulfur in an autoclave at elevated temperature and pressure with oxygen gas. An example is the overall oxidation reactions of chalcopyrite when sufficient oxygen is present, shown in the following reactions:"

Jan 1, 2016

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979