Search Documents

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By Charles A. Rhoades

The Bureau of Mines is conducting research on a dual leaching method that offers the potential for the economic recovery of the silver as well as the manganese contained in some of the domestic manganiferous silver deposits. The method is an initial leach of the manganese with aqueous SO2 followed by a neutralization rinse, and then by a second leach for the extraction of silver with cyanide solution. Refractory silver in these ores is either bound by the high-valence manganese, chemically resistent to cyanide leaching, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when -1 in +1/2 in (-2.5 cm + 1.3 cm) ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct for silver and 65 to 96 pct for manganese were attained in laboratory column leach tests using the dual method on the same size ore pieces from six domestic deposits.

Jan 1, 1984

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By Wade E. Cooper

INTRODUCTION How accurate are past and present employee radondaughter exposure records of underground uranium miners employed in the United States? This often-debated question is essential for future substantiation of safe exposure limits. An apparent discrepancy between company-reported exposures and Mining Enforcement and Safety Administration (MESA) projected exposures was detected in 1977. For these reasons a need for an updated comparison of these exposure data was indicated. This paper gives some of the conclusions of the earlier study and compares more recent exposure records compiled by the Atomic Industrial Forum, Inc., with projected exposures based on sampling by Federal mine inspectors. EARLIER STUDY In its 1977 Annual Report (U.S. Department of the Interior, 1978), MSHA's predecessor, the Mining Enforcement and Safety Administration (MESA), reported that there was "an apparent discrepancy between Federal inspection results and company records." Both company records and MESA's projections from samples taken during routine Federal inspections indicated reductions in the average exposure of underground uranium miners from 1975 to 1977, but the MESA projections were over 4 times higher than the company-reported averages. This apparent discrepancy however, was based on a comparison of exposure data reported for all U.S. underground uranium miners. This projection more closely represented the average exposure of U.S. underground uranium mine production workers who worked 1,500 hours or more during the year. Exposures of such workers are reported each year by the Atomic Industrial Forum, Inc. (AIF) in summaries of exposure data reported to the AIF by uranium mining companies throughout the United States. (The AIF exposure summary for 1979 appears as tables A-1 and A-2 in the appendix of this paper.) Assuming that the average exposure for each exposure range category is the midpoint of each exposure range category, table 1 compares the estimated average exposures for U.S. underground uranium mine production workers who worked underground 1,500 hours or more each year in 1975 through 1977 with the exposures projected by MESA for those years. [Table 1. - Average Exposure and Projected Average Exposure for U.S. Underground Mine Production Workers Who Worked Underground 1,500 Hours or More During the Year. Company, MESA?' Reported- Projected Year (WLM) (WLM) 1975 1.59 5.68 1976 1.84 4.64 1977 1.68 4.08 1 Atomic Industrial Forum, 1976, 1977, 1978. 2 U.S. Dept. of the Interior, 1978.] Table 1 indicates that, even after adjustment to ensure better comparability an apparent discrepancy between Federal inspection results and company reported exposures for 1975-1977 exists; however, the apparent discrepancy diminished over the 3 years. Slade, 1977, explained some of the discrepancy between company records and MESA projections of miners' average radon-daughter exposures as follows: 1) Concentrations of radon daughters in some work areas can vary greatly during any one day. A variation from 0.3 WL to 17.0 WL has been measured in the same stope on the same day. 2) Seemingly simple abatement problems indicated by the regular Federal and State inspections were solved simply by manipulating the mine ventilation. 3) The methods used by mine operators to compute cumulative exposures were such that high radiation readings were seldom or never reflected in the records. For example, a work area sampled on Monday indicated a radon-daughter level equal to 0.2 WL and this was recorded. It was sampled again on Wednesday of the following week and the level was 2.2 WL. The miners were withdrawn or told to fix the ventilation, and when this was accomplished the area was sampled and found to be at 0.2 WL again. Although the miners could have been working in the higher concentration up to 6 days, this reading might never be reflected in their records. If it was recorded, only a fraction of the day on which it was discovered would be entered into the cumulative exposure calculation (time-weighted average). 4) Some of the mines visited used a mine average radiation concentration, and every employee working underground was given the same exposure per unit of time spent underground. As a result of the 1977 study, more stringent sampling and recordkeeping standards were proposed and public hearings held in 1977. The resulting new and revised health standards on radon-daughter sampling and exposure recordkeeping became effective August 30, 1979 (Mine Safety and Health Administration, 1979). Prior to these new regulations, radondaughter sampling requirements were on an "as often as necessary" basis (Code of Federal Regulations, 1978). The new regulations required practically all active work areas in underground mines to be sampled at least once every 2 weeks, with many areas requiring weekly sampling. They also required calendar-year exposure records of all underground

Jan 1, 1981

An atomic force microscopy (AFM) has been applied to study the adsorption of collectors on mineral surfaces in a copper/molybdenum flotation system. AFM images show that collectors absorb on chalcopyrite surface in patches at pH 11. A study of temperature effect on surface morphology excludes the possibility that these patches are nanobubbles forming on hydrophobized mineral surface. Hydrocarbon oil absorbs on molybdenite quickly, while KEX (potassium ethyl xanthate) has little affinity for molybdenite. Pyrite is much more reactive in water and its surface is easily coated in Ca(OH)2 solutions at pH 11. Based on the obtained AFM images, the adsorption of chemicals on mineral surface and its impact on copper/molybdenum flotation were discussed.

Jan 1, 2012

By Stanley N. Watowich

Recently the petroleum market has made us aware that we are indeed global natural resource consumers, and as such, we have become captive to fundamental global resource economics and their attendant vagaries. Global resource supply problems are as old as civilization and mineral exploration one of its important catalysts. On the basis of natural resources empires have been expanded and new frontiers have been developed. Global consumption and production might even be viewed idealistically as a system dedicated to optimizing distribution to the consumer. However, this is not the case. Political instability and increased government polarization make dependency on a global market somewhat insecure. The U.S. must evaluate its domestic mineral re- sources on the basis that all metals are critical and that dependency on even the common and base metals may ultimately weaken our domestic economy and our potential international relationships and could cause critical weaknesses as demonstrated by the petroleum problem. This paper evaluates specifically the Duluth Gabbro Complex, of Northeastern Minnesota, (figure l), as a potential resource of critical and strategic metals. First, a chronology of some of the early exploration, will be followed by more recent intensive company studies and preliminary evaluations of economic feasibility. Lastly, metallurgical data, on some optimum conceptual mining plans will allow metal production data to be compared with an estimate of U.S. domestic needs in 1990. The purpose of this paper is to put into focus the difficulty of converting resources into vitally needed reserves.

Jan 1, 1981

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By Robert Essler, Paul Marsden, Paul Pandrea

"1. THE VICTORIA STATION TRANSPORT HUB Victoria Underground station is part of the Victoria transport hub, which comprises one of London’s main train termini and a major bus station. At the Underground station, the District Line running in the older shallow brick tunnels dating back to 1868 cross the Victoria Line running in the lower tunnels, which were opened in 1969. After Waterloo, Oxford Circus and King’s Cross/St. Pancras Tube stations, Victoria is the most frequented station on the London Underground network and is used by over 80 million passengers per year. Capacity at Victoria Tube station has been inadequate for many years with passenger numbers steadily rising. Overcrowding is a constant challenge and the station has to be closed regularly during morning and evening peaks until sufficient trains pass through to clear the platforms. For this reason an extension has been debated since the 1990s. After intensive preliminary investigations and feasibility studies covering many variants, which included a large-scale jet grouting test to determine the applicability of this technology as a protective measure for the tunnelling works, the project was officially started with the Victoria Station Transport and Works Act Order (Secretary of State, 2009) effective on the 18th of September 2009. Following a competitive tender process a joint venture of Taylor Woodrow and BAM Nuttall were awarded the contract by London Underground, with their design being carried out by Mott MacDonald Ltd. Ensuring the busy station remained open to the public was a key requirement of the Victoria Station Upgrade. Jet grouting works, which were executed from ground surface, were also carried out while the station was fully operational 2. OVERVIEW The Victoria Station Upgrade aims to increase the capacity of the Underground station significantly and one of its major design objectives is to optimise the transfer between the Underground lines. In order to achieve this, the following new structures are currently under construction: •,A new North Ticket Hall •,Extension of the existing South Ticket Hall •,Nine new escalators •,Connecting tunnels between the North and the South Ticket Hall •,8 new lifts providing step free access to all platforms •,An improved connection between the rail/bus terminus and the Underground station As the elevation and geometry of the existing structures cannot be changed, the new structures need to be adapted to the existing structures (see Figure 1)."

Jan 1, 2016

By J. H. Kelley

In this paper, we show that the methane emission and the dust generation in under-ground mining currently and in the future pose operational, health and safety conditions which adversely Impact face productivity and worker satisfaction. One solution is the use of a dual-aircourse system of ventilation. In this concept, one aircourse captures and exhausts to the surface the dust generated and the methane emitted in coal/mineral fragmentation while a second aircourse provides workers with cleaner air for breathing and comfort. Various dual-aircourse configurations adapted to the Variable Wall Miner are analyzed and compared with conventional mining in gassy seams, indicating a marked reduction in the required air quantity and the number of aircourses.

Jan 1, 1996

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

The most important safety aspect associated with great mining height in steeply dipping coal seam mining is the stability and control of the roof. When soft coal and hard gangue make up the immediate roof of a working face, the soft-coal interlayer plays a significant role in gangue damage and can cause problems such as roof collapse in front of the support, collapse of partial area supports and other problems that can affect the stability of the supports and the surrounding rock system. This study found that the first weighting step of a multigangue roof is larger than that of a nongangue roof, but periodic weighting steps are similar. The overburden collapse height is lower in a multigangue roof than in a nongangue roof due to the buffering and supporting function of the collapsed gangue. Failure of the coal interlayer is the key factor in the collapse of multilayer gangue. The limited load of the interlayer and maximum resistance of the support is concluded by the hard gangue and soft coal interlayer mechanical model. The maximum resistance of the support increased with the dip angle of the seam and burial depth. Certain measures are proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

By F. Harold Weber

On July 13, 1967 the San Bernardino County Planning Commission approved publicly a request by American Smelting and Refining Company for a zone variance to conduct a silver mining and milling operation in the Calico district, southern California, Coincidentally, on July 14 the U.S. Treasury halted its sales of silver, and the U.S. free market price quoted rose immediately from $1.30 to $1.77 per ounce. In its request to the commission Asarco stated that about 13,500 to 15,000 tons of rock would be moved daily by surface mining, including 7,000 tons of ore. The ore would be crushed to minus three-quarters inches and the silver recovered "by a chemical process." The grade of the ore was not given, but the company said that it might also recover barite as a byproduct, The operation would employ 150-160 people. Additional activity in the district includes exploration programs by Superior Oil Company and Calico Silver Mines, Ltd. History and production: In retrospect, as the price of silver began to rise in 1961 from 91 cents an ounce, and as Asarco began its exploration program in late 1964, a new era for an old bonanza silver district would seem to have begun. The Calico district has been mined for silver only on a very, very small scale since 1882 to 1896, when an estimated $12 to $20 million (perhaps 15 to 20 million troy ounces) of that metal was produced from the 50-odd mines of the district and vicinity. These mines include the Silver King, Oriental, Waterloo, Garfield, Odessa and Waterman (which is about 8 miles west of the district). Much smaller-valued amounts of barite, gold, lead, and copper also have been produced from the ore deposits of the district; and from 1884 to 1907 the region yielded about $9 million worth of borate minerals.

Jan 1, 1967

By H. Y. Yang, L. L. Tong

For gold recovery, a Chinese refractory, high-sulfur gold concentrate was subjected to biooxidation with high pulp density in a single stirred-tank reactor. The flotation concentrate contained 36.9 percent sulfur (S) and 33.9 percent iron (Fe). Different experimental regimes for biooxidation were applied. With a mixed culture and by controlling the amount of addition of the gold ores and the pH of the biooxidation system, maximum iron oxidation of 82.6 percent and sulfur oxidation of 79.3 percent were achieved. The experimental results indicate that the pH control was beneficial to the biooxidation of this concentrate. Approximately 28.4 percent of elemental sulfur (S8) was found in the oxidizing slags. Two dissolution mechanisms of elemental sulfur are proposed: (1) FeS2 → S80 → S2O32− → SO42− and (2) FeS2 → S80 → SO42−. The high pH had a positive effect on the reduction of the S8. The results of thermodynamic analysis indicate that as an oxidant the dissolved oxygen can effectively reduce the Gibbs free energy of the pyrite oxidation process and, compared with the reaction of ferric iron as the single oxidant, the oxidation of pyrite is easier. The efficiency of the gold recovery was related to the iron oxidation as well as the sulfur oxidation. Gold and silver recoveries of 92.4 percent and 66.4 percent, respectively, were achieved.

By C. C. Jobes, J. J. Sammarco, D. L. Anderson

Computer-aided control of a mining machine places its operator in a safe, remote location, thus reducing health and safety risks. Sensing systems that provide machine position (xy coordinates) and heading (yaw) are extremely useful in aiding remote positioning of mining machines. The US Bureau of Mines (Bureau) developed two sensing systems for position and heading information: a scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system (MAPS), that employs ring-laser gyroscopes (RLGs). This paper presents a brief background and status of these sensing systems as applied to a continuous mining machine (CM). Included are field test results off each system operating in a room-and-pillar research section at a cooperating West Virginia mine.

Jan 1, 1993

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By Gunjan R. Bhattarai, K. Bhattarai

Applications of machine learning and robotics in the tunneling industry are still nascent. Research and development are ongoing in TBM guidance; prediction of TBM cutter wear and tunneling induced ground deformations; and robotic arms for segment installation, inspection, cleaning, and maintenance of TBM cutting tools. This paper presents a case study of geological profile reconstruction using multimodal machine learning. The results from this study can aid the development and application of multimodal AI technologies to generate data reports and geological profiles in real time, taking voice recordings, photos, or videos obtained directly from the field as inputs.

Jun 23, 2024

By Richard H. Johnson

White Pine Copper Company began operating a plant designed to recover copper matte particles from its discarded reverberatory furnace slags in April, 1972. Seasonal operation, generally the months of April through November, continued through October, 1974, shutting down due to feed exhaustion. White Pine reverberatory furnace slags contained economically recoverable amounts of copper for a variety of reasons. Among them: 1. White Pine concentrates yield extremely high matte grades (65+% Cu) and viscous slags. The viscous slags hinder matte settling causing matte "prill" entrapment in the slag 2. White Pine's total refined copper output is accomplished through fire refining requiring special techniques for impurity removal, especially small amounts of nickel introduced from purchased pyrite and chalcopyrite fluxes. These special techniques result in high-copper slags, refractory to smelting, being reintroduced into the reverberatory furnace. 3. Furnace bottom build-ups resulting in mechanical matte entrapment through the formation of "dams" hindering matte flow. 4. Occasional concentrate fluxing and furnace atmosphere control problems.

Jan 1, 1975

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon' as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far and at the same time improves the performance characteristics.

Jan 1, 1977