Search Documents

By W. Clark Ashby

Trees are an essential ingredient of sound reclamation in nearly all surface mining regions. There are, however, possible problems in current reclamation regulations and practices which need to be evaluated and remedied. Recognition and accomodation of growth requirements for trees and other plants will greatly increase reclamation success. Surface mining encompasses a series of processes from a pre-mining baseline study to bond release following revegetation. Land owners, and society, have a great interest in subsequent plant growth on reclaimed areas and in future land values.

Jan 1, 1981

NIOSH is conducting research to reduce the silica dust exposure of workers at surface coal mines. One goal of this research is to evaluate the relationship between drilling parameters, rock strata and silica dust generation. This study involved measuring blast hole emission dust from a rotary drill rig which required sampling high concentration dust (>400 mg/m3) for silica content in a high velocity airstream. To measure dust initially, traditional sampling methods using personal sampling instruments were attempted in and around the shroud area of the drill with no success. Variations in the dust cloud concentrations under the shroud, the condition of the shroud and its orientation over the hole, and ambient air conditions prevented consistent and accurate dust measurements from being obtained. Amore consistent dust cloud is necessary for accurate measurements. An area of the drill’s dust collector system that consistently draws the emitted airborne dust from the hole is the collector tube. This tube connects the drill collector’s vacuum and dust filtration system to the shroud area. Assuming the collector system is working as designed, sampling from the collector tube would enable more consistent and accurate samples to be taken. However, current personal samplers are unable to sample in the concentrations and velocities experienced in the collector tube, so another method had to be devised. To achieve the desired results, an in-stack cascade cyclone was used. Preliminary field testing shows positive results.

Jan 1, 2003

By Robert M. Stevens, Arnoldo Acuña

INTRODUCTION In the early 1950s, underground miners and tunnel¬ing contractors were experimenting with ways to supple¬ment or eliminate track-bound loading and hauling equipment. Diesel-powered crawler and rubber-tire mounted front-end loaders and trucks designed for use on the surface were being modified and tried with limited but encouraging success. Miners began working with interested manufacturers to explore the develop¬ment of vehicles specifically designed to meet the de¬mands and constraints of underground material han¬dling. By the mid 1960s, load-haul-dump (LHD) vehicles were firmly established as a fundamental part of what has become known as the "trackless" mining concept, used in many mines and many countries around the world. The flexibility, mobility, and versatility of these units have given the industry a useful tool and have added new dimensions to mine development and produc¬tion. Many old mines have been redesigned to accom¬modate these trackless vehicles, and few new mining plans have failed to find some use for the concept during some phase of development and production. By 1977, several manufacturers in several different countries were producing a variety of LHD vehicles to meet the growing worldwide demand. GENERAL DESCRIPTION LHD vehicles combine certain characteristics of conventional front-end loaders and dump trucks, spe¬cifically designed for materials handling in underground mining and tunneling. The design intent is to provide one vehicle with one man, with the vehicle loading itself, hauling the load over level or inclined haulageways, and dumping the load. A typical production cycle of the most popular units has the operator driving the vehicle forward, forcing the bucket into the muck at or near floor level, and using the tractive effort of the vehicle and the prying action of the bucket to roll out and tilt back the load as shown in Fig. 1. With the bucket rolled back into the carrying position on the boom and the boom resting on the main frame of the vehicle, the load is hauled (trammed) to the dump point as shown in Fig. 2. At the dump point, the boom is raised, the bucket is rolled forward, and the load slides out as shown in Fig. 3. After dumping, the bucket is rolled back to the carrying position, the boom is returned to rest on the main frame, and the unit is driven back to the loading point for another load. There are two other types of LHD units that are slightly different in the cycles that they perform. One uses a hopper arrangement carried on the front of the machine, with a small bucket mounted ahead of the hopper. Several passes with the small bucket load the hopper, which is dumped by opening its floor. Al¬though this concept is several years old, it has gained less than 0.5% of the total market. The most recent LHD concept differs in that it has one bucket nesting inside another. The smaller inner bucket is loaded first, and it is then tilted back and above the larger bucket. When the larger bucket has been loaded, it is rolled back, and the total load is trammed to the dumping point. The dumping operation tilts the buckets in the reverse order from that of the loading operation. The impact of this new concept on the mining industry has not been measured yet. This chapter concentrates on the LHD vehicles employing the cycle described by Figs. 1 through 3, since these LHD units constitute an estimated 99% of the units in current use. MAIN VEHICLE FEATURES In general, the LHD vehicles available from most manufacturers share the same basic features.

Jan 1, 1982

By Karl Gugel, Dante Garcia, Peter Czel, Eduardo Nunez, Joshua Morales, Boris Sullcahuaman

Real-time operational excellence is achieved through the seamless integration of various components. Key aspects include precise instrumentation, real-time data collection, data analytics, and an efficient optimization platform. Additionally, to ensure success, the real-time optimization platform must be incorporated into the site’s internal process control system (Nunez, 2022). This paper provides an overview of practical lessons and best practices for autogenous (AG), semi-autogenous (SAG), and ball mill (BM) grinding. It highlights the implementation of advanced instrumentation, specifically vibration sensors on the rotating mill shell. The paper also delves into the application of advanced analytics necessary for generating new measurements that accurately represent real-time grinding activity in the mill. These Advanced Analytics Measurements (AAM) are compared with well-known grinding curves to determine the optimal grinding point. The discussion focuses on key industry opportunities using real-time mill shell vibration results to derive new correlations and optimize the grinding process.

Feb 1, 2025

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By I. Cameron-Clarke

This paper describes the design of a wellfield to provide a water supply for a new mine in southern Africa. A hydrogeological investigation was conducted that included the drilling and test pumping of eight wells located within a highly jointed pyroxenite aquifer. The wellfield was designed using a simple probabilistic analysis. This approach allowed the variability of the aquifer parameters to be taken into account. A risk assessment analysis was then carried out to evaluate the level of assurance that a reliable water supply could be provided by the wellfield. The analysis was also used to assess the effects of supplementing the water supply by pumping from nearby flooded workings.

Jan 1, 1992

By Richard L. Gordon, William A. Vogely

ENERGY POI.ICY-PRINCIPLES AND THEIR PRACTICE Persistently, at least since the end of World War 11, governments have intervened broadly, deeply, and incoherently in major energy markets. If we take a broad definition of energy that encompasses gas distribution and electric power, we can observe regulations of even older vintage. This trend, of course, is not unique to energy. Expansion of government controls has occurred in many areas. The relevant basic question about energy regulation, therefore, is not why is energy special, but whether any general principles exist to explain the wisdom of existing regulations. This review takes place at a time, the middle 1980s, in which a massive onslaught is being undertaken against government regulation. However, the present chapter is influenced primarily by my observations of the failures of energy regulations and not by any inspiration from those ideologically opposed to government intervention. Several subquestions arise in policy appraisal. A primary need is to establish clear objectives and determine the consistency between these goals and the policies imposed. Thus, the first step is to set objectives. The next is to outline ways to attain these goals. However, it should be recognized that many apparently distinct options are economically equivalent. When the goal is to charge producers or consumers for something, it is possible to attain the same result through either government ownership or taxing private transactions. The tax can raise the price to the level the government would have charged if it were the owner. Creation of a Department of Energy is not necessarily any different from having separate energy agencies well coordinated by some small supervisory body. Thus, a distinction should be made between substance and form in policymaking. The critical substance concerns such matters as whether the government imposes financial penalties, incentives, or rules to attain a goal. Then, there can be many equivalent ways to implement the basic policy form. The second prior illustration suggests that one favorite question is how to attain proper integration of policy. At various times, voices on either (or even both) sides of the Atlantic have called for a coordinated energy policy. The U.S. Paley Commission made this a primary goal for future policy. The western European governments that were the founding members of the Coal and Steel, Economic, and Atomic Energy Communities spent much time in the middle fifties and much of the sixties trying futilely to agree on an energy policy. (See Gordon, 1970 for an annotated review). The energy price rises of the 1970s rekindled United States interest in coordination. However, astute observers of the problem such as O. C. Herfindahl of the United States and Maurice Allais (1 962) in France warned the discussions confused form with substance. The crucial issues were what were the goals and what were the best types of policies to attain such goals. Policy suffered, not from poor organization, but from discord about the goals and how to attain them. All this suggests that we need principles to guide policy appraisal. The branch of economic theory known as welfare economics concentrates on providing guidance about the problems of policymaking. The theory examines both what

Jan 1, 1985

By Bjorn Olsson

"Heavy impact. High frequency hammering. Extreme abrasion. Building on the experience of owning and operating its own mines, Ovako has developed a deep knowledge of how vital the right steel properties are in withstanding the extreme loads encountered in every part of the drill string. That is why Ovako’s product development process is focused on understanding the specific load cases and manufacturing operations associated with rock tools.The punishing conditions of percussive drilling can push the limits of most materials. And heavy mechanical loads are only the beginning. Highimpact energies at high frequency are a major source of fatigue. High temperatures result from impact energy losses. And abrasive, erosive and adhesive wear are constant risks. Handling any of these varying demands at a single point along the drill string is difficult enough — which makes optimizing for the entire drilling system an extremely complex challenge. Engineering for specific loadsOvako has specialized over many decades in analyzing the dominant loads for each of the parts and components used in rock tools, and testing for individual applications in its laboratories. The most critical fatigue properties are controlled through the steel metallurgy, and supported by performance measurements through extensive rotating bending fatigue (RBF) testing, along with special methods that combine impact load with various wear loads. The result is a fit-for-purpose steel with tightly controlled performance properties, making it possible for customers to precalculate the expected life time of their components for highly automated and repetitive processes Tailoring steels for the processing route.The same levels of control and predictability must be carried through to the customer’s own manufacturing processes. By ensuring minimal variations in chemical composition, everything from heat treatment and welding to automated machining can be carried out with high consistency. With precisely controlled material properties based on an existing processing route and exact load case, customers are able to minimize their total tool production costs while ensuring optimal performance for their end products. Development of Hybrid SteelBuilding on this experience in the mining industry, Ovako has developed a new steel family, known as Hybrid Steel, designed to meet the demands of high-stress, elevatedtemperature applications where mechanical and fatigue strength are critical. Traditionally, steels for these applications are produced by expensive small-batch processes. Hybrid Steel, however, enables high volume production at a competitive cost.The world of steel has traditionally been divided into clearly separated categories of tool steel, stainless steel and lower alloy engineering steel. Hybrid Steel is now challenging that division, offering attractive properties from all three categories."

Jan 12, 2017

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By Kyle Amoroso, Aaron K. McCain

Frozen soil shoring has been used for decades in the tunneling industry to provide temporary support of excavation for shafts and cross-passage excavations. However, horizontal penetrations through the frozen soil can prove to be challenging. The key to creating a stable portal through frozen ground is managing and mitigating groundwater flow into the excavation through the annular space surrounding the drill stem or casing. This paper will review different approaches that have been successfully used to penetrate frozen soil shoring on multiple projects.

Jun 13, 2023

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By D. W. McGlashan

Zeta potential changes were determined as a function of pH, metal ion, and surfactant concentrations. Prom the analysis of data, flotation experiments were carried out to correlate float-ability with the differences in zeta potential. Cassiterite in water bears a negative zeta potential, The zeta potential of cassiterite is sensitive to pH changes; the electric double layer arises from the preferential adsorption of H+ and OH- ions and subsequent ionization of the hydroxylated surface. It is suspected that hydronium-ion concentration may cause reversal in the sign of the zeta potential. The ZPC was found to occur at pH 3.4. Metallic ions and the hydrated ions thereof affect the zeta potential of cassiterite in differing degrees of intensity. Without prior activation, sulfonated surfactants do not change the zeta potential of cassiterite. Sodium alkyl aryl sulfonate is especially active on lead-activated cassiterite and ferric-activated cassiteriten Microcalorimetric fiests confimed the activity of ions on cassiterite and showed the hydrated character of cassiterite smfaces. Close correlation between zeta potential and microflotation results was achieved.

Jan 1, 1969

By Richard C. Fox

"Why geophysics? We will have to drill anyway." Reliance on geophysical methods for detailed target appraisals will increase as direct surface evidence becomes more subtle. This will create a need for more effective and efficient geo- physical programs. Numerous computer-based techniques that deal with a broad range of geophysical problems are described in the literature. The purpose of this chapter is to provide a framework for the systematic application of these techniques to effect an overall optimization of the geophysical appraisal. The concepts described are not technique specific, but should serve as a guide for increasing the effectiveness and efficiency of any geophysical program. Fig. 1 shows a generalized flow chart of the major aspects of the program described. The three main subdivisions of a 'geophysical program are discussed: (1) survey design, (2) data processing, and (3) data interpretation. Detailed flow charts, outlining the goals, the requirements for meeting the goals, and the steps followed within each subdivision are presented at the beginning of each section. The objectives and type problems of each subdivision are defined, followed by a description of applicable computer methods. . References are cited that give a general cross section of computer techniques available in the literature, and examples are given in each subdivision to demonstrate basic concepts and the use. of computers in solving the type problems.

Jan 1, 1979

By J. Ke

Traditional geostatistical methods have been used in ore reserve estimation for decades. Neural Networks (NNs) have provided an alternative approach to data analysis and ore reserve estimation. Unlike the traditional geostatistical methods, neural network uses a highly non-linear complex algorithm to do the estimation. Although Neural Networks have been demonstrated to be attractive alternatives as with every new techniques, there are questions which remain unanswered. This paper presents a comparative analysis with different types of metamodeling approaches -- Triangular, Kriging, Spline, and Neural Network. The neural-network is organized in a multiple-layers and Back-propagation model is used to handle the non-linearity and hidden slabs for smoothing the predicted results. With multiple dimensional and very noisy drill hole sample data, the ore grade is predicted and the overall performance is validated by the analysis of R-squared (R2), Root-Mean-Squared (RMS), and contours of ore grade spatial variability. The ore grade and tonnage of estimated outputs are also compared with various cut-off grades.

Jan 1, 2003

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By Bernard L. Cohen

INTRODUCTION The most serious occupational radiation episode in U.S. history was the exposure of uranium miners to radon daughters in the 1945-1968 time period. Although the maximum permissible dose at that time was 12 WLM (working level months) per year, average exposures were several times that figure, and ten times higher exposures were not uncommon. Starting in the early 1960s, mounting epidemiological evidence appeared for an excess incidence of lung cancer among these miners; up to 1974, there was an excess of 134 cases (159 observed vs 25 expected) among the 4000 in the group under study (NAS-1980). When this excess became apparent, the Federal Government took jurisdiction, greatly tightened enforcement, and in 1969 lowered the maximum permissible exposure to 4 WLM per year. These standards were met largely by a great improvement in ventilation. As a result of these measures, average miner exposures were reduced 5-fold from 1965 to 1968 and by another factor of 3 by 1970. In 1978, the 4 WLM/year maximum permissible exposure was exceeded by only 37 of 7500 underground miners, for only 16 wars it exceeded by more than 25%, and for only 8 was it exceeded by 502 (AIF-1980). The average exposures to the various groups are listed in Table 1. We see that the average exposure for all miners was 1.03 WLM, and for those who worked essentially full time underground it was 1.45 WLM. For purpose of later discussion, it will be convenient to choose a single value for average exposures. In view of the fact that employment situations and job categories are bound to vary over a lifetime of work, we take this to be 1.3 WLM/year. The purpose of this paper is not to dwell on history, but rather to address the question of whether or not this present situation is satisfactory. This question was considered recently by a study group under the auspices of National Institue of Occupational Safety and Health (NIOSH-1980) and it answered the question in the negative, concluding that the maximum permissible exposure should be substantially reduced. However, their arguments were incomplete and were lacking in perspective. The principal thrust of this paper is to provide some of the material overlooked. RISK TO URANIUM MINERS FROM RADON EXPOSURE In order to quantify the risk to uranium miners under present working conditions, it is first necessary to estimate the risk of lung cancer per WLM of exposure. The most straightforward way of doing this is to use the data on the group of uranium miners under study. These are listed in Table 2 for 8 exposure ranges and for the total group (NAS-1980). If all data are given equal weight, the risk is seen to be 3.5 x 10-6 per year per WLM. Much can be said in favor of using this value for the risk as dose independent; it is within one standard deviation (SD) of the observations in 5 of the 8 dose categories (as expected from the definition of SD), and within 2 SD for all 8, and for the three cases differing from the mean by more than one SD, two are above and one is below. However, the uranium miner exposures in the present situation will be far below those covered in Table 2, so it is worth considering the possibility that the risk differs from this at low doses. From the last column of Table 2 we see that the experience from all exposures below 600 WLM indicates a risk higher than the mean for the entire group by more than two standard deviations (the value 600 WLM in this comparison was deliberately chosen to maximize this deviation; for exposures below 360 WLM and 840 WLM, the excess is only 1.0 and 1.6 standard deviations respectively). In view of this tendency for the risk to be higher at lower dose, we will take the risk to be 5.0 x 10-6 per year per WLM in what we will refer to as model A. This risk estimate is based entirely on exposures much [higher] than those that will be experienced by

Jan 1, 1981

The Janet Annenberg Hooker Hall of Geology, Gems and Minerals, located in the National Museum of Natural History, Smithsonian Institution, in Washington DC, opened in September, nine years after initial fundraising efforts were begun. The 1,858-m2 (20,000-sq ft), $16-million hall was mostly funded by private groups and individuals, including $1.7 million from 43 National Mining Associa¬tion (NMA) member companies. Companies that contributed more than $100,000 included Cyprus Amax, Phelps Dodge, Asarco, Homestake Mining, BHP, Caterpillar, Cleveland Cliffs, Exxon Coal and Minerals, Freeport-McMoRan, Newmont Mining and Peabody Holdings. The mining industry's contributions funded a walk-through Mine Gallery. It. features diora¬mas of four mines, as well as numerous specimens associated with the mines. The Mine Gal¬lery demonstrates to the public the importance of mining. The hall was named in honor of Hooker. She contributed $5 million in cash plus the Hooker Yellow Starburst Diamonds to the project. The hall is touted by the Smithsonian as the "most comprehensive earth science complex of its kind." It consists of seven galleries, each devoted to different aspects of gems, minerals and rocks. In addition to the Mine Gal¬lery, the hall contains a collection of gemstones and jewelry pieces, an extensive collection of minerals, a gallery devoted to plate tectonics and a gallery devoted to the moon, meteorites and the solar system. The new hall is a complete makeover of the old and outdated Geology Hall. It was built in the 1960s and finally closed to the public in 1995.

Jan 1, 1997

By William H. Langer

I spent 41 years as a geologist with the US Geological Survey (USGS) conducting geologic studies and preparing peer reviewed maps and reports describing the results of those studies. Since retiring from the USGS in 2011, I have been a consultant specializing in aggregates and other industrial minerals. Consequently, I have had the opportunity and pleasure to apply the information contained in those kinds of geologic maps and reports to real-life situations. About half of my consulting is performing due diligence for mineral resource evaluations of one type or another where resource information has been provided by the property owner. Many of those jobs necessitate that I conduct desktop studies followed by field work. I then use my information to review and comment on the written reports of others; reports variably referred to as geologic reports, resource studies, reserve analyses, and so forth. While there are many well written reports addressing geologic resource issues, I was surprised to see that there are also a significant number of so-called geologic reports that only pay cursory attention to geology. Unfortunately, that lack of rigorous geologic investigation commonly leads to erroneous conclusions. This paper addresses three such reports covering concrete sand, metallurgical gravel, and proppants (frac sand). Although all three examples are located in the Gulf Coastal Plain Province, I do not reveal the exact location of any of the properties for purposes of confidentiality. Furthermore, I have generalized the site descriptions and illustrations. However, all the descriptions faithfully define the geologic situation.

Feb 1, 2024

By R. K. Komarek, F. E. Jr. Briber, G. M. Hanson, Fred D. DeVaney, J. H. Blake, C. L. Matson, T. E. Ban, N. E. Shields, R. D. Frans, R. B. Greenwalt

Metallurgically, the term agglomeration is used to describe processes whose goal is to form balls, briquettes, nodules, flakes, or other sized shaped particles from loose, usually fine, incoherent particles. In practice it includes such varying processes as the briquetting of coal dust and other substances, the balling and induration (heating) of such nonmetallics as cement, fluorspar, lightweight aggregates, etc. It includes such widely used processes as the sintering of nonferrous concentrates, such as those copper, lead, zinc, etc. The agglomeration of specific nonferrous metal concentrates is discussed in detail in the section of this handbook devoted to that particular metal. Agglomeration processes are of particular value to the iron and steel industry where the nature of the primary reduction process, the blast furnace, requires for best results a burden essentially free of fines. This is a change that has taken place since about 1960. Prior to that time many fine unsized ores were fed to the furnace. The development of the pelletizing process gave to the industry a chemically controlled closely sized product that increased the produc¬tion rate and reduced the costs so much that unsized fines are seldom used in modem furnaces. Steel plants produce many fine sized waste products such as fine dust (fine ore coke and gangue) and mill scale. These products, which have a valuable iron content, are usually sin¬tered directly at the plant for reuse. Fine sized ore concentrates are usually pelletized at the mine and shipped as pellets to the steel plant. Common practice in some areas producing natural high grade ores is to screen the ore at the mine to about 3/8 in. The oversize is shipped "as is" and constitutes blast furnace feed. The / in. may be shipped to the steel plant where it may be sintered or otherwise agglomerated. At some mines the fines may be pelletizied prior to shipment. With the development of large ocean ore carriers, and with the transportation of slurried concentrates or fines, a trend has developed of constructing large pelletizing plants or other types of agglomeration plants near large consumption centers (i.e., in the Netherlands or Japan) where ores of many types are brought together, ground if necessary, blended, and agglomerated. As an indication of tonnages of agglomerated materials produced, for iron materials alone (the largest share of the total) production in 1970 in the U.S. was Million gross ton Sinter 40.7 Pellets 43.1 Briquettes, nodules, & others 0.1 Total 83.9 During the 1960s, U.S. production of sinter rose from 40.3 million gross tons in 1961 to a high of 48.7 million in 1964, then settled back to almost the 1961 figure in 1970. Pellet production rose steadily from 14.4 million gross tons in 1961 to the 59.9 figure for 1975. Worldwide, sinter production in 1966 was estimated at 340 million mt (mainly in Europe, Russia, Japan, and the U.S.) and pellet produc¬tion the same year at 64 mt (primarily Canada and the U.S.). World pellet production capacity rose to 200 million tons in 1976.

Jan 1, 1985