Search Documents

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By Paul S. Murphy, Eric W. Oehrke

INTRODUCTION The global market for sulphur has experienced dramatic structural shifts during the past 10-15 years. After a number of years of dominance as sulphur suppliers, the world&apos;s Frasch producers were confronted with large increases in nondiscretionary sulphur production from sour crude oil and gas, while escalating energy and exploration costs reduced the economic incentives to replace dwindling sulphur reserves. Sulphur demand also experienced substantial growth, but the majority of this increase was filled by nondiscretionary production. The result was essentially flat demand for Frasch sulphur during this period. This paper briefly summarizes Freeport Sulphur Company&apos;s outlook for global supply and demand for sulphur through the year 2000, and examines in more detail the history and anticipated shifts in trade patterns. World trade in elemental sulphur (brimstone), despite year-to-year fluctuations, has been on an upward trend in recent years, and should continue to grow through the end of this century. The type (discretionary vs. nondiscretionary) and location of forecast sulphur supply sources has potentially broad implications for the world&apos;s Frasch producers, as they compete in a world market which is increasingly supplied by non-discretionary production. SULPHUR DEMAND Sulphur is a versatile and essential element used in a wide variety of manufacturing processes. Almost 90% of world sulphur consumption is in the form of sulphuric acid. The relatively low cost, ready availability, and physical and chemical properties of sulphuric acid make it the most economical acid for a number of chemical processes. Although sulphur is used in the manufacture of many products, the largest consumer by far is the phosphate fertilizer industry. The majority of sulphur demand growth over the past 30 years has occurred in this area, and today it accounts for nearly 65% of global sulphur consumption in all forms. Due to the relative importance of phosphate fertilizers, sulphur demand is typically discussed in terms of fertilizer and non-fertilizer (or industrial) uses, and this approach will be followed here. We at Freeport believe that global consumption of phosphate fertilizers should grow at an average annual rate of about 3.5% through the year 2000, which is roughly equal to the growth rate experienced during the past ten years. The basic assumption underlying this forecast is that world population will continue to grow significantly, while the total acres of cropland will grow only slightly. Therefore, in order to feed a growing population, higher crop yields will be necessary, which in turn will require the increasing use of fertilizers. This expected growth in phosphate consumption will, without doubt, fluctuate from year to year, and we Frasch producers have painful memories of the large dip in demand during 1982-83. However, we believe that the fundamentals for growth are very good, and that future demand will move back onto the historical trend line. In the recent recession the use of sulphur in the non-fertilizer or industrial sector dropped sharply, and it now appears that future growth will not return to the old trend line. Most of the non-fertilizer uses of sulphur and sulphuric acid involve older industries which are very mature, such as oil refining, steel, pulp and paper, pigments, etc. The use of sulphur in some of these industries is expected to exhibit little or possibly even negative

Jan 1, 1986

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator&apos;s position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By Harrison H. Roberts

A. We are aware that many who are in the audience have perhaps heard before some of the material which will be presented. Since our firm is more closely associated with the heavy construction industry our experience is more oriented in that direction. Notwithstanding this, the subject your program committee has asked us to present centers mainly in the earth-moving field. We find a common denominator between say, the stripping of a site to uncover an ore-body which will be developed by open-pit methods, and that of excavating & transporting materials for an embankment dam, airport or other project. Both are earth-moving problems and we offer for your consideration a means of determining the most favorable method, equipment selection and resultant cost. We do considerable studies involving rock excavation for tunnels, underground powerhouses, inclined and vertical shafts for penstocks, muck-removal, electrical cable & other related underground work. Hence, we believe we speak the same language.

Jan 1, 1972

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By O. Ozcan

Oleic acid has been almost invariably used in the flotation of siliceous fluorite ores. The performance of oleic acid, however, deteriorates with carbonaceous fluorite ores. Oleoyl sarcosine developed recently has been found to produce results superior over oleic acid with ores containing high calcite contents. While the mechanism of oleate adsorption is usually considered as chemisorption involving calcium oleate formation on both calcite and fluorite, no mechanism has been so far proposed to explain the adsorption mechanism of oleoyl sarcosine. In this study, the selectivity of oleoyl sarcosine, as inferred from flotation, zeta potential and infrared measurements, is ascribed to the interaction of fluorine ion to the nitrogen via hydrogen bonding.

Jan 1, 1994

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By A. Ballester, F. Gonzalez, M. L. Blázquez

Pyrometallurgical process are usually used to recover valuable metals from metal sulphide concentrates. However, their use is diminishing as the cost of energy rises and pollution controls become strictes. An alternative method of treatment sulphides could be bacterial leaching due its simplicity and negligible contamination (1-2). This process is presently used commercially to re cover metals such as Cu and U from low grade ore concentrates. In spite of numerous researchs during recent years (3-5) there exists very little kinetic data concerning the speed of bioleaching process. The kinetic analysis of bacterial activity is related with the metabolism and growth of microox ganisms . This fundamental information permits ma- king the best utilization of bacterial oxidation and to suggest techniques which might increase the production of the products desired. However, bio- kinetic models are especially complicated due to the existence of many metabolic routes and parallel reactions which are important for the life of the bacteria. Microbiological oxidation of a mineral substrate is influenced by its own inicial concentration: This influence can be determined by means of a kinetic study. In a medium with sufficient concentration of nutrients (nitrogen, phosphorous and potassium) and an adequate supply of 0, and CO2, as the only & L source of carbon for the biochemical synthesis, the substrate concentration would remain the only limitation in the rate of leaching. In this case the Michaelis-Menten model could be applied (6). The model is based on an association of the enzyme (El with the substrate (S) with consequent decomposition of the latter into enzyme and products [ ] The rate of dissolution is defined by the equation : [ ] Were V is the rate of metal extraction (mg 1-1 1 h-1 ) ; S is the pulp density Mn is the maximum rate for metal extraction (mg 1-1 h-1) and K is the constant of Michaelis (concentration of substrate that yields Vm/2). This method is applicable only when the rate of bacterial growth is similar to the rate of metal extraction. It would therefore be sufficient to control the concentration of metal in the medium over the period of time. In the present work a systematic study of the kinetics of ZnS and CuFeS bioleaching in sphalerite and complex ore concengrates was carried out. The rate of dissolution of the Zn and Cu as function of the pulp density and temperature was determined. However, most oxidations of sulphide dissolution take place with a very slow kinetic; but, this can be accelerated considerably by the addition to the solution of suitable catalytic ions, as was Suggested many years ago by Bjorling (7). Such ions can exercise an important influence on the rate of the oxidation-reduction reactions, both homogenous and heterogenous, which take place during the leaching of sulphides; they also affect the nature of the reaction products. The action of catalytic ions has been fully developed in aqueous systems, but in the absence of bacteria (8 - 11) although the actual machanisms is not totally known. The mechanisms proposed as hypotheses in the literature (8) indicate that, in the case of ZnS, the catalyst ion act through an electrochemical mechanism according to the reactions: [ ]

Jan 1, 1989

By XUEWEN WANG, Changda Zhang, Huaguang Wang, Mingyu Wang, Bin Hu

The copper smelting process produces plenty of copper slag every year, which is a hazardous solid waste, but a secondary resource. In the present study, the extraction of copper, nickel, and cobalt from copper slag was investigated through the process of sulfation roasting–water leaching and the process of sulfation roasting–sulfate decomposition roasting–water leaching respectively. Compared with the process of sulfation roasting–water leaching, the process of sulfation roasting–sulfate decomposition roasting–water leaching is a better choice, which could not only get almost the same leaching of copper, nickel, and cobalt as the former process, but has a lower leaching of iron and aluminum. For the process of sulfation roasting–sulfate decomposition roasting–water leaching, the leaching of Cu, Ni, and Co reached up to 74.2%, 71.1%, and 69.6% respectively, under the optimal conditions including sulfation roasted with 80 wt% sulfuric acid addition at 200 °C for 60 min and sulfate decomposition roasted at 650 °C for 60 min, followed by water leached at 90 °C for 30min with a liquid–solid ratio of 2 ml/g. The leaching of Fe and Al was only 4.9% and 17.6%.

May 4, 2020

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100&apos; to 300&apos; in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By Thomas Schwind, Benedikt Grau, Angelos Gakis

"In Crossrail’s Farringdon station, compensation grouting was successfully utilized to mitigate the surface settlements induced by the tunneling works. The main focus of this study was the platform tunnels, which were approximately 300m long each and were enlarged to platform size using sequential excavation method (SEM) from the existing TBM running tunnels, initially supported using sprayed concrete linings. The rear grouting injections were carried out at a typical distance of minimum 5m above the completed, fully strengthened shotcrete lining hence inducing some additional stresses. In-tunnel monitoring using surveying targets was performed systematically to ensure that no excessive distortion of the initial shotcrete lining occurred. 3D finite element analyses were utilized to back calculate the actual “effective” pressure that was imposed on the completed shotcrete rings against the additional measured in-tunnel displacements due to the compensation grouting episodes. Additionally an assessment of the theoretical, “maximum” allowable grouting pressures that would lead to overstressing of the lining is presented. INTRODUCTION As part of the back analysis performed for the SEM tunnels in Farringdon station, an investigation of the effect of compensation grouting on the two constructed platform tunnels was undertaken. The platform tunnels were 10.6m high by 11.4m wide and approximately 300m long each. They were enlarged to their final shape from the existing TBM tunnels using SCL methods. This study utilized 2D and 3D finite element (FE) analyses in order to back calculate the observed tunnel crown displacement, assessing the equivalent grouting pressures during the rear injection episodes of the concurrent grouting operations. The results provide a useful reference for the order of magnitude of the grouting pressure load cases that can be applied in the numerical simulation of similar cases. Part of the results presented in this paper, were derived by the second author as part of his Master of Science thesis in Technical University of Graz."

Jan 1, 2016

By Mustafa Kumral, Yuksel Asli Sari

Underground mining operations are sensitive to price fluctuations because they usually perform with a narrow profit margin compared to open-pit mining. Furthermore, the economic evaluations regarding operation are based on estimated or simulated grades rather than actual values. These bring a high degree of uncertainty to the viability of an operation. Hence, mine planning that accounts for uncertainty is crucial for underground mining operations. As an underground mining technique, sublevel stoping has geotechnical, curing time, seismicity, cost minimization, and production requirements. A new mixedinteger linear program is proposed that considers the uncertainty associated with net present value using chance-constrained programming. The net present value (NPV) maximization objective is transformed into a multi-objective maximization problem where one objective is to maximize the mean NPV, and the other objective is to maximize the negative standard deviation multiplied by a scalar called risk or reliability level. The balance between the two objectives was maintained by this scalar and was selected based on the reliability level of the project. A case study was conducted with varying reliability levels, and sequences were generated. It was shown that the expected net present value increased at higher reliability levels, and the overall value of the objective function decreased as the reliability level increased. In other words, the variance component penalized the value of the objective function. Moreover, it was observed from the case study that at lower reliability levels, stope grade order bears similarity to the extraction order.

Aug 4, 2023

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By B. H. Johnston, B. N. Doyle

Introduction In 1983-84 Kidd Creek Mines Ltd. in Timmins, Ontario, started up the second commercial zinc pressure leaching plant based on the Sherritt Gordon Mines Ltd. direct pressure leach process. The first plant using this process was that of Cominco Ltd. at Trail, B.C. (Parker, 1981; Martin and Jankola, 1985). The Kidd Creek plant was constructed to take advantage of the extra capacity that the existing purification, cell house, and casting sections had in comparison to the roasters and acid plant. In addition, pressure leaching offered flexibility in other areas such as treatment of low grade concentrates. The process design package and the detailed design of the autoclave system was carried out by Sherritt. The detailed design for the rest of the plant was done by Cambrian Engineering Ltd. under the direction of Kidd Creek. The construction and commissioning of the plant has been described earlier (Johnston, 1983). This paper describes, briefly, the application of the direct pressure leaching process for zinc concentrates and the integration of the pressure leaching plant into the main zinc plant at Timmins. It discusses some of the startup problems and changes made to the plant. The damage following a fire inside the autoclave is also described. The subsequent repair and recommissioning of the autoclave has enabled Kidd Creek to demonstrate the originally sought advantages of pressure leaching and to take advantage of their extra cell house and casting capacity to produce more zinc. Process principles The development of the direct pressure sulphuric acid leach of zinc sulphide concentrate at temperatures above the melting point of sulphur and at elevated oxygen pressure has been described in detail in a number of papers (Martin and Jankola, 1985; Johnston, 1983; Veltman and Bolton, 1980; Kawulka et al., 1975; Veltman et al., 1977). The most significant aspect of the process is that sulphidic sulphur is converted to elemental sulphur in reactions that can be simply described as follows. ZnS + H2SO4 + 1/2 O2 ZnSO4 + S° + H2O (1) FeS + H2SO4 + 1/2 O2 FeSO4 + S° + H2O (2) The rates of these reactions increase with temperature. However, at temperatures above the melting point of sulphur, 12°C, the presence of a surface active agent is necessary to prevent the occlusion of the sulphide particles by elemental sulphur and the consequent termination of the leach. The zinc that is dissolved according to reaction (1), after purification of the zinc sulphate solution, is recovered by electrowinning. The iron that is put into solution according to reaction (2) is further oxidized to the ferric state and subsequently, as the acidity decreases, precipitates as hematite or as complex basic sulphates. MINERALS AND METALLURGICAL PROCESSING Examples of this are shown below. 2FeSO4 + H2SO4 +1/2O2 - Fe2(SO4)3 + H2O (3) Fe2(SO4)3 + 6H2O - Fe2O3.3H2O + 3H2SO4 (4) 3Fe2(SO4)3 + 14H2O - 2(H3O)Fe3(SO4)2(OH)6 + 5H2SO4 (5) (hydronium jarosite) The conventional zinc process involves concentrate roasting to produce zinc oxide and sulphur dioxide. The zinc oxide is leached in spent electrolyte and the sulphur dioxide is converted to sulphuric acid. The pressure leaching process can, therefore, be used to replace conventional concentrate roasting, sulphuric acid manufacture, and atmospheric leaching with one unit operation. Integration of pressure leaching into the Kidd Creek flowsheet A block flowsheet of the Kidd Creek zinc plant, with the new pressure leach plant integrated, is shown in Fig. 1. The original plant, which was constructed in 1972, is based on standard electrolytic zinc plant technology. Concentrates are dead roasted to remove sulphur. Sulphur dioxide is treated to produce sulphuric acid. Calcine is leached in two stages using cell-house electrolyte. Iron is precipitated as jarosite and solutions are purified to remove copper, cobalt, nickel, and cadmium to provide feed for a partially mechanized cell house. Zinc is plated from solution, and the resulting cathode is melted, cast, and sold (Johnston, 1983). The integration of the pressure leaching plant into the main zinc plant is relatively simple. As shown in Fig. 1, a fraction of the zinc concentrate and spent electrolyte are fed to the pressure leach autoclave, while part of the calcine from the roaster is used as a neutralizing agent in the oxidation step along with. the jarosite leach solution. The main exit stream from the pressure leaching plant is the slurry discharged from the oxidation step, consisting of neutral zinc sulphate solution, unreacted calcine, and precipitated iron oxides. This slurry is transferred to the neutral leach step in the main zinc plant. The leach residue from the pressure leaching step, consisting of basic iron sulphate and elemental sulphur, is washed and impounded along with the jarosite residue produced in the main plant.

Jan 1, 1987

By M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material build-up inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 mtpd and significant operating costs savings.

Jan 1, 1985

By Chee Theng

"In 2013, Coeur Mining had more than $55 million in general and administrative (G&A) costs and less than $100 million in cash flow. This year, its G&A costs stand at $30 million, down by more than 40 percent, its all-in sustaining costs have shrunk by more than 30 percent, and its cash flow is above $200 million. To realize this, the company aggressively reduced both its corporate overhead cost and operating cost and repaid more than $300 million in debt.The more robust balance sheet meant the precious-metals producer was well positioned to reap the rewards of an upsurge in commodity prices in the early part of 2016. Its stock price soared from $1.75 in January to $15.98 in August. Although the stock price has since dropped to around $9 due to a stronger dollar and a more hawkish Federal Reserve that recently raised U.S. interest rates, shifting the opportunity-cost argument away from buying gold and silver, Coeur remains attractive to analysts in light of its prudent spending and improved fundamentals.Focus on balanced portfolioCoeur is the largest primary silver producer and one of the largest gold-producing companies in the United States and one of the largest silver companies in the world. Incorporated in 1928, the U.S.-listed company has a total of five operations: three in the United States, one in Mexico and one in Bolivia. About two-thirds of its revenue comes from the United States.The company is conscientious about having a balanced portfolio, so no single mine accounts for more than about 30 percent of its business. Being in three different jurisdictions provides further diversification, and its revenue split of about 60 percent from gold and 40 percent from silver gives it some metals mix. This year, it expects to produce about 466 t (15 million oz) of silver and 10.3 t (330,000 oz) of gold."

Feb 1, 2017

By C. J. B. Dreyer, H. A. Robinson

Only South Africa can be considered in terms of resources of amphibole asbestos. There are two asbestos producing fields, one in the Northern Cape Province (producing only crocidolite), and one in the Eastern Transvaal (producing only amosite). This chapter discusses the banded ironstone sequence in which amphibole asbestos occurs, and the genesis of the fiber is briefly reviewed. Also, the properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300 000 t of arnosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production chat could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. The mining methods are also reviewed and evaluation techniques are discussed. The only two types of amphibole asbestos exploited at present in South Africa are amosite [the white colored amphibole asbestos) and crocidolite (the blue colored asbestos). As is well known, crocidolite has been mined in South Africa from the early part of this century, and amosite since the early 1930&apos;s. Since these dates, asbestos mining has developed into a significant mining industry. The annual production of crocidolite is approximately 170 000 to 200 000 t. and amosite production is in the region of 80 000 to 100 000 t. CLASSIFICATION OF AMPHIBOLE ASBESTOS Four types of amphibole asbestos are produced economically in the world today: (1) crocidolite, the fibrous equivalent of riebeckite, (2) arnosite, the fibrous equivalent of grunerite, (3) trernolite, and (4) anthophylite. The names trernolite and grunerite apply equally to the crystal and fibrous forms of these minerals. For comparison and clarification purposes, the six known varieties of asbestiform minerals known in the world are shown in Table 1. All the asbestos minerals were originally developed as cross fiber seams in veins or fractures, or were controlled by the lithology. Post- fiber effects caused slip, sheared, and folded fiber seams. Crocidolite and amosite occur in banded ironstone of early Proterozoic age of the Transvaal Supergroup. The fiber seams are developed in certain defined lithological units in the banded ironstone sequence. The lithological units have a remarkable lateral persistence with respect to their chemical nature and physical appearance. Vertically, the banded ironstone sequence displays a heterogeneous nature. Commercial Applications The features and properties that make amphibole asbestos commercially attractive are: 1) The long average length of the fibers is good for greater wet strength in composites. 2) The high tensile strength of crocidolite makes it superior to all other types of asbestos. 3) It is characterized by dispersion in most liquid media, particularly amosite in water. 4) Since the surface charge of amosite and crocidolite is negative, the fibers produce an open lattice work in water with a high bulk volume giving excellent filtration rates and rapid drainage in a wet asbestos cement mix. 5) The insulating properties of amphibole asbestos mats are still important, particularly in a corrosive environment, despite the introduction of many other synthetic insulating materials. 6) Corrosion resistance, particularly acid corrosion resistance. 7) Due to the high modulus of amphibole fibers, resins reinforced with these fibers exhibit

Jan 1, 1986