Search Documents

By I. Kapageridis

The mining industry worldwide has recognized in the past the need to apply specific rules and guidelines in the reporting of mineral resources and reserves. The high financial investment and risk associated with any mining project and the ever stricter environmental and social controls were the forces behind this recognition. For years the industry experienced the development and enforcement of several codes for reporting accepted by different countries. The implementation of any code can be a confusing task as the guidelines are sometimes general and open to different interpretation. The use of computers in the estimation and reporting of mineral resources and reserves is necessary, particularly when trying to implement particular code guidelines. This paper discusses ways to implement a reporting code in a computerised resource/re-serve estimation study. The implementation is demonstrated using a gold deposit project as an example. The effects of mining, metallurgical, economic, marketing, legal, environmental, social and governmental factors are taken into consideration. This paper also discusses well established reporting codes and the possibility of reaching a single, universally applied code that could be used by Greek mining companies.

Jan 1, 2007

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By John McMorran

An open pit mine design system should have the characteristics of being flexible, versatile, and simple. All of these characteristics are necessary for producing a dynamic mine design. In other words, a design that can be improved, updated, and implemented. Flexibility is an important characteristic due to changing times. For example, the effects of a changing economy, increased knowledge of the mineral deposit, or improvements in mining technology can result in a considerable, if not a complete change in the long range mining plans. Since the short range mining plans are based on the long range mining plans, they will-also be effected. Also, it is very important to validate the information used in the design or the design itself. This means the system should have the flexibility of being able, not only to detect, but to correct errors. Versatility is another important characteristic of a mine design system due to the wide range of situations that may appear. First, a design system must be able to handle both long and short term planning. This is necessary because of the variability in the definition of a time range. Second, a design system must be able to handle different types of deposits. Special emphasis must be placed on this issue, because many deposits, if not the majority, do not fit predefined categories such as bedded, massive, or roll-front, etc . . . Furthermore, the true test of the versatility of a design system is not only the ability to create an ultimate design but also to schedule sequences for this design. Thus, the versatility of being capable to design with a variety of time ranges, variety of deposit types, and scheduling are all important characteristics of the design system.

Jan 1, 1982

By Edgar O. McAlister

Associated with cordilleran intrusives of intemediate to acidic composition, gold/silver ores are generally found in the intruded host rocks which are adjacent to these intrusives. Generally precious metal deposits lie further from the intrusives than allied base metal deposits. For vented intrusives, the associated volcanics may constitute the intruded rock and form the host for precious metal accumulation. Potential field methods, particularly magnetics, can help to define unseen boundaries of intrusive systems and thus can point to generalized prospecting targets. Other clues arise from the intrusive system type, its emplacement fracturing, the host rock type and local magnetic changes caused by mineralization processes.

Jan 1, 1984

By E. Viet Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corporation, Santa Rita, New Mexico, local studies of the dump leaching process were intensified. As these studies progressed it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between leach solutions and the copper-bearing material would determine, in great part, the recovery of values. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers), and mathematical or laboratory model studies. These methods have not proved completely satisfactory for the studies now being developed. Investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drill holes, which are petro¬leum exploration and development techniques for locating fluids and measuring porosity in the subsurface. Standard oil field logging equipment was leased, modified, and tested. After successful testing, the equipment was purchased for additional studies. Applications and results of the methods are described in this paper.

Jan 1, 1968

By G. T. Swanby

Members of AIME, I read to you now a portion of a very fine business letter which we received several years ago. This letter originated in Rangoon, Burma, and reads in part: "Rest assured, if your goodselves see with us eye to eye, sure as certain we should get the business". I don't plan to give anybody "the business" today, but you can rest assured that if some of "you goodselves see with me eye to eye" on what I am about to discuss, I would be most pleased. My talk with you today will discuss the Federal Corporate income tax and its effect on our lives as engineers. In the-engineering-construction business we are faced with all the usual form of taxation which includes such items as sales tax, use tax, school tax, contractor; gross receipt tax, import duties and excise taxes, severance taxes, etc, adinfinutum.

Jan 1, 1965

By George D. Haley

This report will be given in two sections. The first sec¬tion outlines techniques and equipment to form almond shaped fluorspar briquettes by means of briquet presses, and the second section outlines techniques of the balling disc. PART I - BRIQUET PRESSES Fluorspar has been briquetted for a number of years and the so called "peach pit" briquet is known to many steelmen. Present production is estimated at over 100,000 tons annually. Slide 1 shows an assortment of various sizes and shapes of briquettes. It is possible to form fluorspar into almost any configuration of briquet. For safety on the melting floor, pillow type briquets are preferred. Ease of mechanical handling and durability of the product are facil¬itated by an almond shape. The dimensions of the almond can vary from 1-in. to 1-1/2-in. in length, from 13/16-in. to 1-in. in width and from 1/2-in. to 1-in. in thickness. The type of equipment to pro¬duce almond shaped fluorspar briquettes is shown in Slide 2. Here we have a Komarek-Greaves and Company 300 ton briquettor equipped with almond rolls. This machine is capable of producing fluorspar briquettes at a rats of 30 tons per hour with power consumption of 35 hp per ton par hour.

Jan 1, 1969

By Ritika Kundu, Moussa Wone, Amanda M. Morgan, Tatiana K. Proctor

The Piney Branch CSO 049 Storage Tunnel (PBST) will be the last major project for the DC Clean Rivers Program. The project includes construction of a 2,200-foot-long, 18-foot-internal-diameter storage tunnel; two connections to combined sewer infrastructure; and two shafts. Major challenges include excavation underneath an existing live outfall that must remain in service; excavation of the tunnel through several areas of low rock cover and mixed-face conditions; and negotiations with a variety of federal, regional, and local stakeholders to address project impacts. This paper describes the overall project scope; geotechnical conditions along the alignment; design and construction challenges; and construction procurement.

Jun 23, 2024

By Y. Luo

"Investigating abandoned mine subsidence is often a difficult task because many factors, both mining- and nonmining-related, can affect the possibility and the formation process of surface subsidence events over abandoned underground room-and-pillar mines. Among them, mine water frequently plays an important role in causing such subsidence events. However, mine water could also serve the purpose of preventing subsidence. The dewatering of abandoned room-and-pillar mines has been identified as the main cause for a number of serious mine subsidence events in the past.In this work, the mechanism of mine water to prevent surface subsidence over abandoned room-and-pillar coal mines was studied. Two mathematical models are proposed to quantify the potential effects of mine water on the structural stability of mine pillars, roof and floor as well as the potential for causing surface subsidence. The models are validated with an actual case. IntroductionThe potential for room-and-pillar mining operations to induce surface subsidence is mainly dependent on the recovery ratio in the underground mines that directly relates to the stability of pillars. Normally, if the recovery ratio is less than 50 percent, the mine pillars are sufficient to support the overburden strata without their collapse in a sufficiently large contiguous area. Consequently, there will be no surface subsidence. However, if the recovery ratio is greater than 70 percent, the pillars are too small to support the overburden strata and can cause immediate surface subsidence. In 1993, a mathematical model and program was developed and proposed (Luo and Peng, 1993) to predict surface subsidence caused by high-extraction, roomand- pillar mining. When the recovery ratio is between 50 and 70 percent, the mine pillars could be loaded near their critical condition and, therefore, the surface subsidence is uncertain to develop. If the surface subsidence did not occur immediately, mine water starts to fill the underground openings. If thick, clay-type rock layers are presented in the mine roof, floor or pillars, they can be considerably weakened by mine water and cause surface subsidence. The techniques to investigate subsidence events over inactive room-and-pillar coal mines caused by the weakening effects of raising mine water to the claystone immediate roof and floor were presented in Luo (2009, 2011)."

Jan 6, 2018

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By C. H. Rawlins

The total amount of ferrous slag generated in the U.S. is about one-third the amount of iron ore mined, thus ferrous slag can be considered a significant mineral body for processing. Steelmaking slag contains up to 30 wt.% metal of which only the >25mm fraction is commonly recovered. A grinding study was conducted of BOF, EAF, and LMF slags using the Bond Work Index method to determine grindability to 106µm. Work Index values obtained were 13.8-24.9 kWh/ST, depending upon the slag type and composition. Steel particles were magnetically recovered from the crushed and ground samples for size-by-size analysis, yielding up to 18 wt.% of the slag weight recovered as magnetic. The recovered material, as characterized by inert gas melting, was found to be 61-96 wt.% metallic.

Jan 1, 2008

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

This chapter contains the edited transcript of the "Gold Heap Leach Information Exchange" session that was held at the 1990 SME/AIME Annual Meeting in Salt Lake City, Utah. The exchange occurred on the afternoon of February 27, 1990. The session was intended to act as a forum for discussing some of the more prominent operating problems associated with heap leaching precious metals. The information exchange was very successful. The exchange consisted of several panelists introducing and discussing different topics, follow by a comment and question period. This transcript contains the panelists' presentations as well as comments and questions from the floor and the panel. Extraneous comments and remarks have been edited out. Some wording has been changed for clarity, but the transcript is basically an accurate account of what was said. At the end of the transcript are two papers submitted as part of the panel discussion

Jan 1, 1990

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By Leo G. Martin, Richard G. Sherman

Recent sewer construction in downtown New Haven, CT required avoiding open trench methods because of near surface utilities and traffic congestion. The .73 km long alignment is in sands with the water table at the tunnel's springline. The designers felt the situation was ideal for an EPB machine; however, the tunneling method was left to the Contractor. The winning bid surprised everyone. The tunnel is being excavated by hand using an open face shield with breasting boards. The review of the bids indicates hand mining was approximately 1/2 the bid price of TBMs. Currently, excavation rates average 14 m/day with no excessive settlements.

Jan 1, 1993

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005