Search Documents

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By M. Shen, T. D. Wheelock

The important characteristics of a gas-promoted oil agglomeration process for cleaning coal particles in an aqueous suspension were determined. Numerous agglomeration tests with scale-model mixing systems of different sizes with controlled amounts of air were conducted. The tests were conducted on high- and mediumvolatile bituminous coals using either i-octane or hexadecane as an oily agglomerant. The performance of the system was characterized by employing the minimum time required to produce spherical agglomerates (tE), the mean agglomerate diameter (dp), coal recovery and product ash content. Among these parameters, tE was found the most useful. It is a key parameter in the scale-up of an agglomeration mixing system. This parameter was found to depend on a number of system and operating variables. By controlling these variables and conducting further agglomeration tests with mixing systems that varied in size, an appropriate size scale-up rule was established.

Jan 1, 2002

By E. O. Mixon, Joseph P. Sehulster

This paper describes the driving of a 1421 m long by 2.74 m diameter sewer tunnel in postglacial soils of the Menomonee River Valley in Milwaukee, Wisconsin. An earth pressure balance machine was used for excavation and to install a "one pass" pre-cast concrete gasketed segmental liner. Also discussed is the use of ground freezing to stabilize the ground for the start of tunneling operations and modifications made to two structures to accommodate final tie-ins for the sewer tunnel.

Jan 1, 1989

By Lorraine B. Burgin

The extensive lead time to develop most Arizona copper deposits commenced with initial production efforts before the turn of the century, when the first attempts were made to recover gold and silver and later copper from the high-grade vein deposits of the territory. Each of these discoveries, prospects, and early operations had its own lead time and life cycle as economic production was attempted. Because prices of the metals fluctuated and the higher grade material was depleted, economics forced operations to close and companies to fail. Renewed interest in the property because of improved conditions, different interpretation of the geologic structure, or new promotional ability frequently resulted in the formation of yet another company to finance the exploration and, hopefully, the development of the property. This cycle of renewed activity and subsequent abandonment was and is common, accounting for many lead times and for the long period of time from the initial location of claims to large-scale production. In order to gain a perspective on the lead-time interval necessary to achieve development of a large-scale operation, the histories of several major Arizona mines were examined, rather than a simple listing of discovery and production dates of many mines to arrive at a statistical average. The Miami, Castle Dome, Copper Cities, San Manuel, and Twin Buttes properties were studied, and as much data as possible obtained on the Pinto Valley, Esperanza, Sierrita, Pima, and Mineral Park-Ithaca Peak properties.

Jan 1, 1974

By Robert E. Murray

The title of my paper, "A Company's Response to Federal Coal Leasing," brings to mind a picture of a dog chasing its tail. This is what the coal industry, has been doing since the Federal coal leasing moratorium went into effect in 1971. We've gone around in many circles, but we are only very slowly, if at all, getting closer to catching our tails, i.e., efficient, economical, and rational Federal coal leasing. My companies, The North American Coal Corporation and its four Subsidiaries, The Falkirk and Western Plains Mining Companies and The Coteau and Missouri Valley Properties Companies, together hold in excess of 4.5 billion tons of lignite reserves in North Dakota. Some of our North Dakota properties are substantially interspersed with Federal coal, with the government holding title to the minerals in every other section. This checkerboard pattern of Federal ownership has made it difficult to develop and market some of our reserves, and, as a result, it has become imperative that we be familiar with and active in the Federal Coal Leasing Program.

Jan 1, 1982

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended 524 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than one metre in width to pipes with a surface area of 128ha. The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments.

Jan 1, 1984

By S. Odell

The Bureau of Land Management (BLM) has constructed two biochemical reactor systems (BCRs) to treat mining influenced water from the Forest Queen Mine near Silverton, CO. The bioreactors coupled with a natural wetland provide treatment to the Forest Queen Mine drainage. The central objective of this paper is to review the performance of the bioreactors and wetland treatment system. The bioreactors have been in operation for nine years and along with the natural wetland are still removing a high percentage of the influent metals.

Jan 1, 2010

By David G. Chedgy

The Meadow River No. 1 Preparation Plant, owned by Sewell Coal Company, a subsidiary of the Pittston Company, was commissioned in the spring of 1974. The plant is designed to process 400 TPH of 5" x 0 raw coal. The 5" x 114'l fraction is processed in a Heavy Medium Vessel with the 114 x 28M reporting to Deister Tables for cleaning. The 28M x 0 fraction is cleaned in flotation cells, with the froth going to clean coal vacuum filters and the tailings to a static thickener where the underflow is reclaimed on Refuse Filters prior to disposal. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the noise exposure in that particular environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: [ ]

Jan 1, 1976

By L. Kulik

Sustainability of lignite mining in the Rhenish lignite mining area is ensured by a preceding study of the overall project, with the involvement of all those affected. The supporting holistic consideration of the various sustainability elements is essential for a later balancing of the several ecological, economic and social concerns. In what follows, a brief overview of the Rhenish lignite mining area is given as introduction to the focus of this report, which is on sustainability, starting with the approval procedure under regional planning law incl. opencast mine planning, and extending to concrete on-the-spot implementation, taking the Garzweiler II follow-up mine as example. To illustrate the issues involved, an account is given of some selected sustainability elements.

Jan 1, 2005

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By James E. Kolesar

An essential prerequisite to expanding the application of longwall mining techniques in the United States is the development of a better understanding of the mechanics of rock mass deformation near the mined seam, in the inter- burden and at the surface. The results of studies of this type will provide a basis for the development of empirical and/or numerical modeling techniques to predict the rock mass response to mining both near and far from the mined seam. This will lead to improved gate and panel design, resulting in maximum recovery, increased productivity, as well as provide a mechanism for assessing likely surface effects induced by long- wall mining. Presented here is the instrument plan to be used at Kitt Mine No. 1 in the study of rock mass response to two adjacent longwall panels.

Jan 1, 1982

By Gordon F. Revey

In underground construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speedup the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high. In this paper, general methods of conducting blasting risk evaluations and outlined and considerations for blast design and risk management are reviewed. This paper also includes three blasting case histories demonstrating how these techniques were used at recent projects. In the first case, a cautious blasting program was developed to facilitate the removal of concrete and rock within a large section of an active mineshaft. The second case involved critical blasting to excavate a dry lake-tap connection between a tunnel and a shaft at the Southern Nevada Water Intake No. 2 project in Henderson, Nevada. The third case history describes how novel blasting methods were used to carefully drop a 2,721,500-kg (6,000,000-lb) concrete caisson into a1.2-m (4-ft) rock socket at the Detroit Outfall No. 2 project in Detroit, MI.

Jan 1, 2001

By C. R. Kuhn

From 1968 to 1975, most work in surface modification of inorganic materials involved silane coupling agents. A silane coupling agent can be described simply as an oganosilicon chemical having a general formula RSi-X3 wherein the R group is attached to a silicon in a thermally and hydrolytically stable manner, and X is a hydrolyzable group usually having an alkoxy functionality. About 1975, Kenrich Petrochemicals brought into the market place titanate coupling agents. Titanate coupling agents usually consist of one alkoxy group and three functional groups attached to a central titanium atom. Zircoaluminates became available in about 1982. Zircoaluminate organometallic coupling agents, which vary principally in their respective organofunctionalities, arise from a basic technology in which two different types of organic ligands are selectively bound to a low-molecular weight zircoaluminate backbone.

Jan 1, 1995

By D. T. Iseley, David Bennett, Christopher Norris

The microtunneling test program is one of three main elements of the research project, "Trenchless Construction: Evaluation of Methods and Materials to Install and Rehabilitate Underground Utilities." The other elements of this project include an evaluation and demonstration of horizontal directional drilling technology and pipeline rehabilitation systems. The research is a Corps and Industry cost-shared project funded under the Construction Productivity Advancement Research (CPAR) program. The laboratory partner is the U.S. Army Engineer Waterways Experiment Station (WES), Geotechnical Laboratory. The industry partner is the Louisiana Tech University's Trenchless Technology Center. Industry participants are contributing over half the total cost of this research. The overall objective of the CPAR program is to improve productivity in the U.S. construction industry, thereby enhancing the competitiveness of the U.S. industry in domestic and overseas markets. The Corps and other federal and state agencies will benefit by realizing reduced costs, enhanced safety and better products and services as the products of this research program are developed, tested, and pushed into the market place. The microtunneling demonstrations and evaluations were performed during September and October 1992 at a specially constructed test facility built at WES in Vicksburg, MS. The test facility is 104 m (340-ft) long, 5 m (16-ft) wide, and 4 m (13-ft) deep. It was constructed, ironically, by first excavating a trench into which 6 different types of soils were placed and compacted in approximately 18.3 m (60-ft) long sections. The soil profiles include a lean silty clay (loess), a dry sand, highly plastic buckshot clay, wet sand, clay gravel and silt. The interfaces between soil profiles were sloped to simulate mixed face conditions as the machines exit one zone and enter another, and provided challenges to ground control and alignment and grade control during these transitions. Moisture and density tests were performed on all materials in each lift to assure uniformity. Horizontal inclinometers and 3 levels of settlement plates were installed at key locations in the test bed. The settlement plates and rods and the horizontal inclinometers, together with surface survey points, provided data to evaluate settlement and heave along the test section. Penetration resistance was measured in each section of the completed test bed. Strain gages were installed in 8 of the 0.6 m (24 in.) diam. Hobas pipe sections to measure strains in the pipe as it was being jacked into place. Steering jack loads, jacking thrust loads, and cutterhead torque were also measured during the drives. The results of these tests will be used together with other information to develop guidelines for conducting feasibility studies and selecting proper methods compatible with anticipated conditions.

Jan 1, 1993

By F. Villanueva Araya

Compania Minera Disputada de las Condes (CMD), an Exxon Affiliate stewarded by Exxon Coal and Minerals Company, operates two' copper mines and concentrators in Chile. Pilot plant studies were initiated in 1984 using a 0.46 meter and a 0.91 meter diameter column for the cleaning of copper concentrate. This eventually resulted in the design and operation of a rectangular column with an area of 6.8 m2, increasing the final copper concentrate grade from about 30% to almost 32'1. Cu without any loss in copper recovery. Evaluation studies of a commercial bubble generator as against the previously used filter cloth air sparger are now in progress.

Jan 1, 1990

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981