Search Documents

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By Henri Letient, Tom Aley, David Evans

Antamina is a large open-pit copper and zinc mine located within the Central Andes of Northern Peru at an altitude of 4300 masl. The facilities are situated within the headwaters of several watersheds, within the Amazon basin. Nearby villages rely heavily on springs and streams for drinking and irrigation water. The principle source of baseflow during the dry season is from Cretaceous karstic limestone aquifers. Antamina will produce nearly 1.4 billion tonnes of waste rock over its mine life. Finding suitable sites for storing large volumes of waste rock is often a challenging task – especially in karstic, alpine terrain. Detailed hydrogeological investigations are essential for delineating the karstic hydrogeologic watersheds associated with the proposed waste facilities, which are often very different than topographic (hydrologic) watersheds. Contamination vulnerability mapping at Antamina consisted of geological and karst mapping, geophysical surveys, geochemical testing, dye-tracer studies, drilling and aquifer testing. Detailed mapping followed by dye-tracer studies proved to be the most cost-effective methods for characterizing the karst aquifer systems. The results were used to optimize waste rock management at the site to minimize potential impacts on groundwater resources.

Jan 1, 2005

By Charles K. Presley

This paper deals with drilling large diameter shafts for the mining and construction industry with diameters in excess of 3 feet to more than 20 feet in diameter. It discusses appropriate applications of the rotary drill method, linings for large diameter shafts, circulation systems,, and the limitations of the method. Each specific rotary drill method is determined by the geology of the area, the depth to be drilled and the formation fluids encountered. Shaft lining or casing must be improved to result in lighter weight, higher strength and lower cost. All phases of rotary drilling equipment must be improved to drill shafts in excess of 10 feet in diameter. As these goals are reached, more shafts of large diameter will be drilled by the rotary method for the mining and construction industry.

Jan 1, 1967

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By A. E. Raddatz

The U.S. Department of the Interior, Bureau of Mines, is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nevada, hot springs ores. The deposit contains disseminated tungsten, which cannot be beneficiated by conventional techniques and must be treated by hydrometallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hr, quenching in a solution containing 1.5 parts of NazCO3 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution- to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hr, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 pct WO3. The pregnant solution contained 11 q of W03/1.

Jan 1, 1982

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By D. R. Taylor, R. G. Goss

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 - 300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: 1) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By B. D. Hong

The Coal supply and demand review arrived too late to appear in the May issue. In 1991, the US coal industry produced 902 Mt (994 million st) of coal, according to preliminary data compiled by the Energy Information Administration (EIA) (Table 1). This amount was 32 Mt (35 million st) less than the record 933.5 Mt (1 billion st) produced in 1990. Most of the decrease in coal production occurred east of the Mississippi River. The substantial stock buildup that stimulated production in 1990 was not repeated in 1991. In addition, coal consumption by electric utilities and coke plants dropped by about 1.8 Mt and 4.5 Mt (2 million and 5 million st), respectively. Moreover, a higher level of coal exports failed to bolster the 1991 production. Production Surface mines accounted for about 59% of the 902 Mt (994 million st) of coal produced in 1991. Underground mines produced for 41%. More than one-fourth of the total coal output was from federal and Indian coal leases. Production of all ranks of coal, except subbituminous, declined in 1991. Bituminous coal is produced mainly in the East. It totaled an estimated 590 Mt (651 million st), a 6% decrease. Production of subbituminous coal, mostly in the West, rose 3% to a record 228 Mt (252 million st). Lignite output was from Texas and North Dakota. It decreased by 1 % to 79 Mt (87 million st). Anthracite production, all from eastern Pennsylvania, fell by 17% to 2.7 Mt (3 million st).

Jan 1, 1992

By Doug Harding

The 3.5 km long Ashbridges Bay Outfall in Toronto, Ontario, Canada was a challenging drive set below Lake Ontario. After a remote machine acceptance due to the global pandemic, an 8 m diameter Single Shield machine launched in March 2021 from an 85 m deep shaft and began its bore in shale with limestone, siltstone and sandstone. During excavation, the TBM and its crew bored a city-wide record of 30 rings in one day, or 47 m of advance. This paper will cover the unique project, from TBM acceptance through to launch, tunneling in difficult conditions, and completion in 2022.

Jun 13, 2023

By Rebecca A. Miller, Terry M. Hertel

In-pit identification of neutral waste rock at the Zortman and Landusky minesites in Montana, by visual and chemical analy­ses, will assist in proper segregation and placement of rock so that soil and water resources can be protected. The use of too few or very general segregation criteria to identify neutral waste rock can result in ineffective waste rock segregation. Conversely, the use of overly restrictive criteria can result in the unnecessary loss of valuable reclamation material that would otherwise have to be mined elsewhere and hauled to the site. Recognition of nonre­active materials can be accomplished on a site specific basis with the use of visual observation and simple chemical analyses. The choice of chemical parameters used to analyze rock samples is constrained by the length of time needed to conduct the test. These analyses must require no more than 24 hours to complete so mining can proceed without delay. Limits set for the chosen parameters must be reasonable and defensible. To achieve these objectives over one thousand samples were collected at the Zortman and Landusky minesites and clas­sified by rock type, total sulfur content, paste pH, and net neu­tralizing potential (NNP). In addition, over 22 humidity cell kinetic tests were conducted to help corroborate static results for waste rock. Another 8 humidity cells were configured in series to test waste rock blending and waste rock/limestone capping alternatives as mitigation for acid rock drainage. Leachates were analyzed for pH, conductivity, alkalinity, acidity, sulfate, Al, Cd, Cu, Fe, Mn, Zn, Mg, and Cr in some cases. Petrographic analysis, as well as total sulfur content, paste pH, and static and kinetic test results identified three geochem­ically different waste rock groups: 1) Archean amphibolite gneiss and Paleozoic carbonates and shales, 2) Tertiary syenite porphyry, and 3) other less abundant Tertiary igneous and Archean metamorphic rocks.

Jan 1, 1996

By John L. Shafer

A process for the conversion of stibnite (Sb2Sj) concentrates, crude antimony oxide, or metal to a pure cubic antimonous oxide (senarmontite) has been developed on a laboratory scale. The conversion of stibnite to senarmontite has been piloted. The high purity of the final product is the result of forming antimony trichloride as a low temperature distillable intermediate. To obtain the antimony trichloride the stibnite, or crude oxide is slurried in molten antimony trichloride and reacted with gaseous hydrogen chloride. Antimony metal is oxidized to the trichloride with chlorine. The hydrogen sulfide produced from the hydro- chlorination of stibnite can be upgraded to a strength of 95% or greater for further treatment. The crude antimony trichloride is separated from the gangue by a preliminary evaporation and then is fractionally distilled and the trichloride distillate has less than 50ppm of arsenic and lead combined (the most troublesome impurities in antimony processing). The purified antimony trichloride is then hydrolyzed with sodium or ammonium hydroxide to produce the cubic form of antimonous oxide (senarmontite) to the exclusion of the rhombic form (valentinite) which is photosensitive. The advantage of this process is the ability to treat a wide range of antimony ores, concentrates, and metal to yield a high purity oxide in a controllable range of particle sizes.

Jan 1, 1975

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022

By M. Xing, S. Usman, K. Awuah-Offei

"While mines generally focus on achieving operational efficiency, creating shared value for all stakeholders is also a management goal. This includes taking a holistic view of their supply chains and increasing local participation. This paper examines the role of supply chain management in mine management; in particular the effect of a strong local supply chain on regional economic impacts. Using input-output analysis, the impact of a local supply chain on a mining sector’s regional economic impact is examined by increasing local sourcing (increasing local purchase percentage -- LPP) for 10 key commodities. An approach, based on multipliers and excess local capacity is used to identify key commodities. The impacts examined are sales, employment, labor income, and value added. The work is illustrated with stone mining and quarrying in Missouri. Ten percent increases in LPP of the key commodities, in this example, result in $4.1 million additional impact on the Missouri economy. This work can provide insight on how to better create shared value for all stakeholders. INTRODUCTION Little research has been published on improving mine supply chain management (SCM) to enhance regional economic impacts. Although some extensive academic research has explored the importance of an industries’ supply chain, not much is known about how a locally-based supply chain increases shared value in the resource sector. Across industries, traditional SCM is getting more and more complex. This is true of the mining sector as well. However, this increased sophistication is not directed towards increasing shared value for all stakeholders, particularly, the local communities. Further research is required to develop new SCM strategies that enhance local participation. One major point of difference between this work and traditional supply chain management is the inclusion of stakeholders’ shared value as a goal in SCM. Creating shared value has become a business goal in recent years (Porter and Kramer, 2011). The authors use input-output analysis (Leeuw, 2012) to evaluate the regional economic impacts of supply chain decisions, which is not part of traditional SCM. Although input-output analysis has been applied to SCM for decades, most of the research uses input-output analysis as a tool to advance an industries’ own operational efficiency (Accenture, 2014)."

Jan 1, 2015

By Nicole R. Henderson

Many mining engineering graduates enter the mining industry lacking training in mine emergency management. As a result, mining universities in the United Sates and other countries are beginning to form volunteer student mine rescue teams to train mining engineering students in handling mine emergency situations and give them hands-on experience managing potential emergency scenarios underground. In the early 1980s, the Missouri University of Science and Technology developed the first collegiate mine rescue team in the United States. For approximately 30 years, it was the only successful collegiate team until the Colorado School of Mines (CSM) started its program in 2009. Currently, there are at least five collegiate teams in the United States and one in Canada. At the Freiberg University of Mining and Technology in Germany, the goal is to adapt the Colorado School of Mines Mine Rescue Program to develop a collegiate team of its own. Currently, mining engineering students cover the theoretical basics of mine rescue in an occupational health and safety lecture and take a basic, one-day mine rescue training course at the Central Mine Rescue Station in Leipzig. The course covers the basic mine rescue topics and gives students the opportunity to experience working in elevated heat and smoke conditions while wearing breathing apparatus. This training gives students a small insight into the importance of mine rescue and mine emergency management. Collegiate mine rescue teaches students the importance of mine rescue and mine safety by giving them hands-on learning experiences before entering the mining industry.

Feb 1, 2014

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By A. Davis, K. Nelson, C. Webb

Abandoned mines in parts of the Black Hills of South Dakota have the potential for acid rock drainage. For this work, ten sites were examined on Black Hills National Forest land or on private land whose drainage could affect Forest Service land. Water samples from all the sites had pH values less than 6. Results of analyses from water samples and rock samples showed a correlation between metals content and pH. Acid-base accounting was used to determine acid drainage potential of the sites. One site (King of the West Mine) had a high potential for acid generation; fortunately, little or no surface runoff leaves the mine site. Six sites appeared to have moderate potential, including the Minnesota Ridge Mine, which currently is being remediated. Three of the sites had low acid drainage potential.

Jan 1, 2004