Search Documents

By J. G. Groppo, S. M. Khandrika, B. K. Parekh

It is shown that dewatering of fine coal particles (D50 = 21 µm) is enhanced near the point-of-zero-charge. The coal surface is modified by the addition of copper ions and by adjusting the pH to precipitate surface-active metal hydroxy species, which promote agglomeration and produce low-moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and the correlations among them are presented.

Jan 1, 1995

By III Sadler

Processing bauxite and clay ores to reduce Iron content to levels low enough for the ores to be suitable raw materials for such products as refractories and abrasives has long been regarded as a diffi9ult problem. Standard magnetic separation processing of the untreated ore has been attempted by previous investigators with only limited success due to the finely divided state and weak magnetic susceptibility of the iron minerals (hematite, geothite, etc.) present in these ores. The new process described in this paper consists of calcining the finely crushed ore at 500 to 800 C and then reducing (with hydrogen, carbon monoxide, etc.) the iron oxides present to magnetite or elemental Iron. The magnetic susceptibility of iron in these forms is enhanced 40-to 100-fold over that of hematitie and is readily removed by simple magnetic separation. Starting with a 2.7% Fe20s Alabama bauxite ore, a 1.5% Fe20s product was produced in one pass through a Davis tube magnetic separator with 95 + % recovery of the iron-free bauxite fraction and a 20% Fe20a magnetic product. These findings suggest that with the addition of light calcination, reduction and magnetic separation steps to the conventional refractory grain production process, the large U.S. reserves of high-iron bauxites could be used.

Jan 1, 1990

By Kanaya Koichiro

Doyashiki Concentrator in Hanaoka mine of Dowa Mining Co., Ltd. started the operation in 1943, treating the ore mainly from Doyashiki ore deposits. After the cessation of mining of Doyashiki ore body in 1973, Doyashiki concentrator began to treat the ore from Fukazawa mine instead in the same year, and furthermore the ore from Ezuri mine In 1979. Currently Doyashiki concentrator treats 30,000 tons of ore per month from both mines. The ore treated is complex sulfide ore, called "Kuroko" (black ore), and the principal minerals contained in the ore are chalcopyrite, galena, sphalerite, pyrite, and barite, accompanied by bornite, tetrahedrite, tennantite, covellite, stromeyerite, argentite, polybasite, pearcite, and electrum. The Principal gangue minerals are quartz, gypsum and clay. The grade of the feed to the concentrator averages 0.9 p/t Au, 110 g/t Ag, 1.1 %Cu, 2.8 %Pb, 9.2 %Zn, 5.0 % Pyrite-S and 13% BaS04. The feed is, after washing and two-stage crushing, ground to 88% minus 200 mesh in a rod mill and ball mills with cyclone classifiers, and five concentrates are recovered by flotation. Primarily copper-lead bulk concentrate is recovered by sulfurous acid-lime flotation method, and then from the bulk concentrate copper concentrate is floated by hot pulp flotation method, sinks being lead concentrate. Zinc concentrate is recovered from the tailing of copper-lead bulk flotation, pyrite concentrate from zinc flotation tailing and barite concentrate from pyrite flotation tailing. The final tailing is sent to the dam.

Jan 1, 1982

By D. L. Schenk

The Navajo Mine is exclusively a multiple-seam surface coal mine located in the northwest comer of New Mexico. The property is situated entirely on the Navajo Indian Reservation. It is owned and operated by the Broken Hill Propriety Co. Ltd., of Melbourne, Australia. The mine began production in January 1963 with a long-term fuel supply agreement with the Four Corners power plant. The 2175 MW nominal generating capacity of the Four Corners powerplant consumes 7.2 Mt to 7.7 Mt/a (8 million to 8.5 million stpy) of coal. The Navajo Mine has estimated reserves totaling 1 Gt (1. I billion st) of strip minable coal. Only about one-third of that total is presently committed to the generating station. As development continued over the years, mining operations advanced into more complex geologic areas to satisfy the utility's demand for coal. To optimize the committed reserve and provide competitively priced coal to the customer, the Navajo Mine began developing a new pit in June 1986. The Dixon Pit boxcut development was completed in April 1987. About 6 hm3 (7.9 million cu yd) were stripped, uncovering 929 kt (1 million st) of coal. Strip ratio was 7.74:1 including 36.8% rehandle of prime yardage. This case study of the fourth production cut highlights a variety of dragline stripping techniques including highwall bench (overburden) side cast, intermediate highwall bench (parting-interburden) side cast and spoilside bench (partings-interburden) stripping methods. The Dixon Pit offers considerable challenges in the surface recovery of up to seven seams of coal within the 1432 m (4700 ft) of total pit length.

Jan 1, 1990

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By J. D. Miller, P. L. Sibrell

The nature of surface sites for the adsorption of gold from alkaline cyanide solutions has been investigated using samples of synthetic, highly-oriented pyrolytic graphite (HOPG). This HOPG material offers an idealized graphite structure enabling the independent study of the graphitic basal-plane sites and the edges, or defect sites, of the graphitic planes. Radiochemical and X-ray photoelectron spectroscopic experiments independently demonstrated that gold adsorption was much higher on the edges (defects) of the graphite planes than on the planes themselves. These results suggest that site-specific adsorption is prevalent in the adsorption of gold by graphitic carbons (including activated carbon, carbon black and graphite) and that most of the favored sites are at edge defects in the graphite crystal structure.

Jan 1, 1993

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1998

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By R. J. Sandberg

The Copper Creek area, part of the Bunker Hill District, Pinal County, Arizona, lies within the southwest porphyry copper province of North America at the intersection of a northwest trend and an east-northeast trend of Laramide porphyry copper deposits. The Copper Creek area has been mined and explored for copper and molybdenum since the early 1900?s. The majority of this work focused on the more than 400 surface exposed breccia bodies. In the 1960 to 1970?s deeper drilling discovered a deep porphyry copper-like setting. Redhawk Copper currently has NI 43-101 compliant resources of about 0.652 billion pounds of measured and indicated and 2.745 billion pounds of inferred copper equivalent in breccia hosted and porphyry style deposits. See Figure 1.

Jan 1, 2010

By R. C. Timberlake

In the past three years there has been a great amount of attention given to phosphates world wide, and in particular to the Florida Phosphate Industry. I would like to relate some of the most recent history of the industry and give you a personal outlook for the future. Phosphate rock has been produced in Florida since its discovery on the Peace River in the 1880&apos;s. Through 1976, approximately 720 million ST of rock had been mined from Florida reserves, and it is my opinion that there are at least 1.2 billion tons remaining which are consolidated, accessible and can reasonably be expected to be permitted for mining. Over half the 1.2 billion tons will be deeper, more scattered, leaner and will produce lower grade rock than the Bone Valley of Central Florida has tradition-ally produced. In 1973, &apos;74, &apos;75 and &apos;76 the Florida Phosphate Industry produced 32.6, 34.0, 38.2 and (38.0) (P) million ST of phosphate rock respectively. This rock was produced by ten mining companies, Agrico, Borden, Brewster Phosphates, Gardinier, Grace, IMC, Mobil, Occidental, Swift, and USS Agri-Chem; mines are located -17 in Polk County, one in Hillsborough County and two in Hamilton County, Florida. Phosphate rock is used by local companies in Florida primarily to produce phosphoric acid from which DAP and TSP is manufactured. Florida acid producers use about 15 million STPY in acid plants in Florida, and another 7.5 million STPY is consumed by acid producers in plants on and near the Mississippi River. Somewhat

Jan 1, 1977

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

By Ryne Goodnough

INTRODUCTION The Wyodak Mine is located in the northern Powder River Basin of Wyoming and is thought to be the oldest continuously operating coal mine in the United States, having recorded yearly production since 1923. The mine has expanded over its 80-plus-year history from an underground room and pillar operation to a modem surface snip mine. Currently, the mine feeds four on-site power plants using conveyors, has a filly automated truck load-out, and ships coal by rail to nearby Wyoming power plants. Annual production of 4.8 MTFT is accomplished on a single-shift basis with 53 fill-time production, maintenance and administrative personnel. In 1990 a decision was made to modernize the coal feed system to the power plant complex with modular conveying equipment. The project involved constructing coal storage silos, overland conveyors, feeder breakers and modular conveyors to follow the mining benches. Total project cost in excess of $25 million was used to construe or commission: A 2,150-TPH 48-inch overland conveyor with horizontal curve A 2,150-TPH 48-inch plant feed conveyor 13 shuttle conveyors, each 150 feet in length 2 front-end loaders equipped with large coal buckets 2 crawler-mounted feeder breakers with compatible discharge conveyor 1 high-lift shuttle conveyor with adjustable discharge height 1 high-angle conveyor 2 4,500-ton coal silos with automated truck load- out capabilities. Conceptually, the plan was to develop 33 MTONS of reserve adjacent to the plant complex and use front-end loaders to tram ROM coal to in-pit feeder breakers. The primary crushing would reduce coal to 6-inch minus and feed through a series of shuttle conveyors to an overland supply conveyor. The overland conveyor would feed the secondary crusher, and the crushed product would be moved to any of four storage silos using conveyors. The in-pit crushing and conveying system is a unique fit for the power plants and provided many interesting challenges for the coal mine to overcome. System integration, maintenance windows, equipment availability and the like had a major role in engineering the system to a power plant complex having no emergency coal stock- pile and limited plant storage. In crediting the designers and operators, the in-pit conveying system at the Wyodak Mine has delivered coal to the power generators since 1994 with little or no downtime. ENGINEERING CONSIDERATIONS Yearly production for the mine is based on 3.5 MTPY which requires about 1,550 TPH on an 8 hour, one-shift- per-day, 5-days-per-week basis. Considering efficiencies for starting and stopping, crew transport, loader trams, and operational delays, a nominal conveyor feed rate of 2,150 TPH or 72% system utilization was used in engineering design application. This ton-per-hour basis is used to size and commission the remaining components of the in-pit system. Coal quality requirements also played a role in equipment selection. The mine reserve grades vertically and coal from Upper and Lower benches needed to be mixed in any given proportion. This required equipment to be filly variable and capable of producing all or part of the 2,150-ton-per-hour requirement. Bisecting the 80-foot- high coal face for quality required construction of a high lift module capable of reaching a single overland conveyor 40 to 50 feet above the pit floor. Designers built a high-lift, adjustable and portable module specific for this application Having two bench systems capable of each producing the required feed for the power plants required computerized control processes to control on-line production. RSLinx, RSLogix, and RSView were chosen as the communication and control software, and a Data Highway Plus serves as the communication backbone. Each of the two in-pit benches are controlled with a data center equipped with Allen Bradley 5-40 processors. This

Jan 1, 2004

By M. T. Ityokumbul

The effect of reaction conditions on the desulphurization of oil sand coke residues has been studied. The variables investigated were temperature, reaction time, heat transfer resistance, and mode of caustic soda addition. The results obtained show that oil sand coke desulphurization increases with temperature, reaction time, and heat transfer rate. In an oxidative environment, coke combustion during molten caustic leaching (MCL) commences at temperatures above 500°C. The mode of caustic addition has no effect on coke desulphurization.

Jan 1, 1995

By Mark Alan Marlkos

Blebs of solid bitumen from the Magmont West orebody of the Viburnum Trend were examined and analyzed in an attempt to relate hydrocarbon distribution and origin to ore genesis. The bitumen was calculated to be approximately 48 to 63 percent aliphatic and is considered to be a polymerized normal crude oil. Polymerization, which was probably caused by water-washing, hardened the bleb surfaces and appears to have "frozen" the blebs during primary migration from local source beds. Comparison of the bitumen to kerogen in local shaly partings strongly Indicates that the oil was derived locally. The polymerized oil blebs are considered to have been derived from a type II (marine) kerogen. Textural analyses indicate that oil migration occurred after lead-zinc mineralization and at temperatures that exceed normal ancient or present geothermal gradients. The following sequence of events is postulated for the Magmont West orebody: 1 Generation of hydrogen sulfide during diagenesis of a normal organic-rich carbonate sequence. 2 Introduction of pulses of hot, metal-rich fluids that resulted in: a Lead-zinc mineralization by the following reaction: Me++ + H2S ? MeS + 2H+ b Solution of carbonates by excess acid produced during the above reaction. c Brecciation of host rock in some cases. 3 Passages of the pulse resulted in: a Carbonate buffering of fluid system to more alkaline conditions. b Precipitation of dolomite c Slight temperature drop. 4 Eventually the high temperatures Introduced by heated brine caused oil generation and initiated primary migration. 5 Water-washing and mild biodegradation altered the hydrocarbon blebs to their present composition.

Jan 1, 2013

By B. A. Ferguson, P. W. MacMillan

INTRODUCTION Jack Spalding in Deep Mining, Chapter 3, states: "In deep mining, to start stoping an orebody without a definite plan of operations covering the whole extraction from beginning to end is to invite serious trouble. Any stoping without plan is bound to leave, toward the end, a number of pillars, remnants, or promontories, which, as they are reduced in size, are liable to fail and cause a general collapse. The object of stope planning is so to mine an orebody that at no stage in the operation is a remnant left. Definition: `When a block of ore is stoped in such a way that eventually a small piece is left entirely surrounded by stoping, that piece is termed an island remnant.&apos; The design of and adherence to a plan of stoping is of greater importance in preventing rock bursts than the type of ground control adopted." This, of course, is just an example of the old axiom that an ounce of prevention is worth a pound of cure. And in this context, mining does not have to be very deep before poor ground conditions, made worse by lack of good planning, force a mining company to resort to more expensive methods of ore recovery. At all times when rock pressures become excessive, stoping plans must be devised to avoid the creation of pillars or promontories. This is most readily recognized when mining deep narrow ore veins by open methods. It would be a little more general to say that stoping systems should seek to avoid or minimize localized concentrations of rock stress. Ore bodies, and particularly those at Falcon¬bridge, can reach large widths and leaving pillars for extraction at a later time cannot be avoided. However, good planning can reduce the effect of factors which create bad ground conditions. The necessary ingredients of planning are time and information: time to formulate and revise ideas; information, gained in exploration and early development, to provide the fullest knowledge of the ore body. In this way, plans become meaningful. It must always be kept in mind that the long-term results of good planning often require decisions not compatible with reaching earliest full production. PLANNING FOR DEEP MINING At Falconbridge Nickel Mines ore bodies presently being found and prepared for production lie at depths in excess of 610 m (2000 ft) below surface. Current un¬derground exploration is being directed towards favor¬able locations below 914.4 and 1219.2-m (3000 and 4000-ft) depths, at most mines. The Onaping Deep ore body has been traced to a depth of 1508.8 m (4950 ft) and at Falconbridge mine the ore body is under develop¬ment below the 5000 level. Planning for more efficient ground control has therefore become an important con¬sideration of future mining. HYDRAULIC BACK FILLING AND CUT-AND-FILL STOPING The advent of hydraulic back filling has led to the increasing use of flat-back cut-and-fill stoping methods during the last ten years, until it has probably become the commonest method of mining deep ore deposits in Canada. These methods account for almost all the pro¬duction from Falconbridge Mines at this time. The ad¬vantages claimed are: safety-a minimum of open ground; very little supplementary ground support (except rockbolted backs and walls); greater selectivity and flexibility in extraction (horizontal extension of the vein, high grade ore stringers going out into the walls); and high productivity and increased mechanization in larger ore widths. There is some difference of opinion as to whether hydraulic classified tailing back fill provides any great resistance to initial closure of the stope walls. The evi¬dence available suggests that it does not. Addition of portland cement to the back fill just prior to placement has produced a material having the properties of a weak concrete. It is confidently expected that this material will assist greatly in the efficient mining of pillars and generally in giving increased ground support to oppose closure. PRINCIPLES OF STOPE PLANNING BY LONGITUDINAL FLAT-BACK CUT-AND-FILL Again quoting from Spalding: "The practice of con¬trolling output by stopping and starting stopes is bad¬stopes once started should proceed without interruption, and control must therefore be obtained by altering the rate of stoping. It is therefore necessary that faces should normally advance at a medium rate which can be boosted, if required, to give temporarily a greater output. Modern high productivity stoping methods, however, generally aim to achieve and maintain the maximum output possible from a stope. Control of tonnage and grade, therefore, becomes a more complex problem requiring very careful scheduling and organiza¬tion. With the basic method of flat-back overhand stoping using hydraulic fill, it is not usually possible to mine in such a way as to avoid creating pillars." Consider an ore body as illustrated in Fig. 1. It is 274.3 m (900 ft) high by 228.6 m (750 ft) long on strike and averages 4.6 m (15 ft) in ore width. It rep¬resents approximately 907 000 t (1,000,000 st). The ore body could be mined by advancing one long single face through all the levels from bottom to top. A total face length of 228.6 m (750 ft) would accommo¬date five 45.7-m (150-ft) stopes. See Fig. la. Each of these stopes would produce approximately 1814 t/m (2000 stpm) and the ore body would require a period of ten years for complete extraction. A possible im¬provement to this scheme might be to stagger the indi¬vidual stope faces. See Fig. 1b. Problems of hanging wall failure can be reduced by this arrangement. From the point of view of reducing travelway maintenance, it is good practice to employ a stoping system of retreat. Stopes farthest from the shaft are mined first so that on completion, haulage drifts below can be aban

Jan 1, 1982

By Robert E. Haun

Retech&apos;s Plasma Arc Centrifugal Treatment (PACT) system is a thermal technology that uses heat generated by a plasma torch to treat hazardous waste containing metals and/or organics. Metal bearing solids and soil are melted by the process, and organic contaminants are thermally destroyed. The molten material forms a hard, glass-like leach resistant mass after cooling in a mold. This paper discusses plasma processing in general and presents some results of treating mineral processing wastes using the plasma arc centrifugal treatment process.

Jan 1, 1995