Search Documents

By S. J. Stokowski

An extensive drilling and laboratory testing program indicates that diagenetic dolomitization of the Oligocene Sombrerito Fm. limestone, southwestern Dominican Republic, is detrimental to the usefulness and quality of the potential construction aggregate resource. The first part of this program was the collection, photographing, and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I (youngest) approximately 10 m of white, dense marine limestone; II, approximately 5 m of white, interbedded dense and chalky marine limestone; III, 2+ m of tan, chalky calcitic dolomite. Unit I has been often altered by lateritic weathering and/or dolomitization; Unit II is often altered by dolomitization. The quarry layers were individually crushed, by core, into coarse aggregate sizes for chemical and physical (specific gravity absorption, MgSO4 soundness, sand equivalent, and LA degradation) analyses. The non-weathered units decrease in coarse-aggregate yield and quality with depth and dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value, an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average 5-cycle MgSO4 soundness by about 17%.

Jan 1, 1987

By H. M. Garrett

Dr. Ft: L. Handy of Iowa State University's Engineering Experiment Station very handily reduced the relatively complex cement making process to ultimate simplicity: "Take two cups of crushed limestone; add one-half cup of clay or pulverized shale (plus perhaps some sandstone or iron ore; depending); mix thoroughly and grind up fine. Bake in white-hot oven at about 2,600 F. Cool. Add a tablespoon of gypsum: and, again, grind very fine. If you can do this for about a penny a pound, you can almost compete.' Before Dr. Handy's time, is the early days of the U. S. Cement Industry, from 1817 when the Erie Canal was started to 1895 when the first rotary kiln was built, this was the recipe, more or less. Dr. Handy's raw materials were deposited in a natural "cement rock" found in the Hudson, New York and Lehigh, Pennsylvania valleys. At first the natural rock was pulverized (not ground fine) and interlayed with wood for "baking" at about 1,800° F in a batch process vertical shaft kiln or beehive oven; then the calcined pozzalonic (lime and silica) product was cooled and ground fine for shipment in wooden barrels. Later, in 1871, true portland cement was made. The same natural rock was ground fine to make briquettes; interlaced with wood or coal in the "Beehives"; and baked at a clinkering temperature of about 2,6000 F to produce clinker (calcium silicates) which was ground fine for sale. In those days, the crude cements dropped in price from over 1 cent to 1/2 cent per pound. In 1895 the rotary kiln introduced-continuous instead of batch processing. The countercurrent process allowed the same raw materials (now finely ground to about 80% minus 200 mesh like face powder) to be fed at one end of the rotary kiln. Heat from a coal burner was introduced with combustion air at the other end to produce the requisite clinkering temperature. The clinker product was discharged for atmospheric cooling, mixed with gypsum, and again ground fine as face powder. The cement was sold primarily in barrels, later in jute or cloth bags, then paper bags, and now primarily in bulk truck and barge carriers. The price dropped to a 1/4 cent per pound by 1910, but with recent inflation it now sells for 2 cents per pound.

Jan 1, 1978

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By Ronald J. Roman

A mathematical model was developed for the grinding and flotation section of Union Carbide's Bishop mill and this model was used to indicate how variations in grind, retention time, and calcite and fluorite content effects the mill capacity, tungsten units produced, and the grade and recovery of the scheelite concentrate. A model such as this is a starting point in determining the economic optimum running condition for a mining and milling operation and an example of this is given.

Jan 1, 1969

By Christopher P. White, John R. Wagner

This paper will discuss the complex and difficult soil conditions encountered in the sinking of 15 shafts of 18m to 27m depth and the excavation and lining of 6700m of 2.74m dia. interceptor sewer on Staten Island, New York. The complex soil profile consists of dense glacial till and sand outwash strata overlying the much older cretaceous sand, silt and clay strata. The tunnel varies from 8m to 14m below the nearby sea level. A significant amount of boulders were anticipated in the till. therefore, a decision was made to excavate the tunnel with a digger shield installing bolted, gasketed concrete segments. The bid documents stated the soils were dewaterable. Several conditions occured in this complex soils matrix which required modifying the planned means and methods including the necessity to use compressed air. The conditions encountered and the equipment used will be described.

Jan 1, 1991

By A. L. Coello Velázquez

The subject of this paper is particle population balance models (PBM) that describe mineral impact crushing behavior; it is mainly concerned with the selection and fragmentation distribution function due to their importance in this context. The data obtained by Datta (1999) by applying impact pendulum testing to single limestone particles, used by Austin (2002, 2004a and 2004b) to obtain the principal parity of fragmentation functions, were processed in order to compare them with the results of other authors, such as Nikolov (2002 and 2004) and Vogel and Peukert (2003 and 2005) so as to increase knowledge of impact crushing. From this data it has been possible to obtain the performance models of the principal parameters of fragmentation function, thereby reducing the number of experiments necessary to model the impact crushing process. The authors also propose a simplification of the selection function model posited by Austin (2002).

Jan 1, 2011

By G. Kris Kapoor

Each new period of public concern, whether rooted in things political, social, economical, or technological, brings with it new words or phrases which highlight that new interest. With people's awareness of our rapid depletion of readily available energy sources and the enormous increase in energy .costs came the new, and now often heard, terms "energy intensive", "energy sensitive", and "energy conservation". Since its birth in 1926, Fuller Company had been directly associated and involved with energy intensive products and processes. We are located in the heart of the Cement Industry. Many of our products and processes are geared to the needs of the portland cement manufacturer, and a look at the inferno within an operating cement or lime kiln will certainly convince anyone that here is an energy intensive process. Fuller Company, then, has always been energy sensitive. Process kilns, hard rock crushers, tube and roller mills, fluid bed thermal reactors, pneumatic compressors and conveyors, material coolers - all are Fuller Company products utilizing or transferring large amounts of energy. Consequently, much of our success in the marketplace depends on how wisely we design and plan for efficient use of power and for conservation of each unit of heat available.

Jan 1, 1975

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By Thomas B. Faddies

The Trixie mine is located in the East Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1983

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By R. E. Nelson

The Alton Coal project, located in south-central Utah, lies at one point just over six miles from Bryce Canyon National Park. This region of the southwestern United States has been called the "Golden Circle" of national parks and monuments. Can a mine be inserted into this region so that it does not intrude on this spectacular landscape? The Alton Coal Project is a proposed surface coal mine designed to serve as the fuel source for the Harry Allen Power Plant, a 1,000 megawatt generating station planned for a site 25 miles northeast of Las Vegas, Nevada. The mine and the power plant will be connected by an underground pipeline through which coal will be transported in slurry form.

Jan 1, 1988

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By M. Tirmarche, J. Brenot, J. W. Piechowski

INTRODUCTION Statistical analysis of results obtained by workers survey is very often limited to the determination of the collective dose and mean annual values. This information is not sufficent by itself for radiation protection purposes since the cumulative exposure of a worker during his working life is not taken into account. A more complete analysis would be obtained by considering both: [ ] These two notions are different. The former depends on the evolution of the protection with time and is related to annual limits (ICRP, 1977 and ICRP,1977 a). The second depends mainly on the works performed during the period of survey, the interference of protection evolution is weakened. So it is useful to foresee how the individual average annual doses would be when considering survey periods of 5, 10 years, or more. STUDIED POPULATION In order to analyse the two previously mentionned notions it is necessary to follow up a well defined population of workers which is continuously exposed to the radiological hazards on a long enough period. The selected population is that of the workers of the French uranium mines always present during the 1971-1979 period (9 years). The number of individuals is 937. The radiological hazards are: 1. exposure to radon and short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation. The workers of the uranium mines are exposed to these radiological risks in different ways according to the work performed. It is therefore necessary to subdivide the population into more homogeneous groups with respect to the radiological risks. Three groups are considered: - Group 1 : 227 individuals whose radon and dust exposures are always nil - Group 2 : 449 individuals whose radon and (or) dust exposures are different from 0 every year - Group 3 : 261 individuals represent a mixed category. Some features of these groups are given in table 1. [ ] The 937 followed individuals represent approximatively the half of the whole population of the French uranium mines. Taking into account the procedure adopted to select the studied population, it appears clearly that this population is not representative of the whole miner population. DOSIMETRIC RECORDS Three risk indicators are considered .Individual annual exposures to radon and its shortlived daughters. They are determined by ambient monitoring based on radon concentration measurements and recording of the times elapsed in the various workplaces. For each worker the annual exposure is represented by the mean annual air concentration and is expressed as a fraction of the maximum annual concentration (MAC). Given the administrative arrangements and the effective state of equilibrium between radon and its daughters, the maximum annual concentration is practically equivalent to 1 Working Level = 2.08 x 10- 5 jm-3. (UNSCEAR, 1977). . Individual annual exposures to long-lived ore dust which are also expressed in fraction of the maximum annual concentration. . Individual annual doses of external irradiation (X and [y] rays) expressed in mSv (= 10-3 Sievert). Irradiation monitoring is based on use of individual film badges.

Jan 1, 1981

By John W. Rold

These encompass all adverse effects of oil shale mining, processing, and ancillary developments on the environment. Specific problems concern: land, vegetation, wildlife, water, air, population growth, aesthetics and public emotion; and fall into four categories of: land, water, air and emotion. Land includes excavations, spent shale disposal, loss of vegetation and impact on wildlife and domestic grazing, plant sites, buildings and roads, necessary urbanization and the total aesthetic or visual Impact. Water considerations are: requirements for Industrial and domestic supplies, adverse effect of underground water on mining, avoidance of pollution or adverse effect on surface or near-surface water, and the utilization or safe disposal of liquids. Air problems include dust, smoke and stack gas, Public emotional problems include reaction to the above problems, and misconceptions of oil shale country and an oil shale Industry. Government and industry are aware of the problems, and are seeking solutions. Last year, the three affected states studied oil shale environmental problems and solution costs. Colorado estimated environmental costs would add approximately 7% to construction and 7% to operation. The report suggested research in: (1) Water availability and impact; (2) Disturbed lands revegetation and rehabilitation, including spent shale; (3) Environmental inventory and impact; and (4) Regional development and land use planning. Governor Love appointed a 47-person committee representing Industry, government and environmentalists to attack the problems. Research pro-posals were prepared to focus on each problem. $715,000 state, federal and industry money is being committed. Results should provide data for industrial solutions and equitable agency administration.

Jan 1, 1972

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By Robert L. Akright

The Sumich (Victorine) gold mine is located in the Toiyabe Mountain Range on the east side of Victorine Canyon, a north-trending branch off Kingston Canyon in the northwest quarter of Section 27 and southwest quarter of Section 22, T16N, R43E, in the southern end of Lander County, Nevada (Fig. 1). HISTORY Discovered in 1862, the Victorine reached a peak of development between 1872 and 1887. The "Victorine" and "Morning Star" lode mining claims, located on the outcrop of a prominent auriferous quartz vein, were patented in 1869 and 1891, respectively. 1, respectively. Gold ore was mined underground in adits driven, on the level, directly into the side of the mountain. Ore brought to the surface was trammed about 457 m (1500 ft) south on a track constructed along the contour to ore bins. From this transfer point, the ore was moved by aerial tram to the bottom of the canyon then hauled by horse-drawn wagon to the mill located about 3.2 km (2 miles) east down Kingston Canyon. Exact details of the milling process used on the Victorine are lacking, but old reports mention water-driven stamp mills, amalgamation, chlorination, and cyanidation. Gold and silver mill products are reported to have been sent to England for final refining. High-grade gold values of 103 g/t (3 oz per ton) remaining in mine walls and on outcrops, attest to the lack of success in treating the Victorine ore in the early mills. The Victorine mine may have been worked sporadically after 1887 with little success. In 1934, control of the property was acquired by William P. Moloney, an attorney from Marion, OH, who also control- 1 led an interest in the successful Goldacres mine in Lander County, NV. This property was studied, sampled, and metallurgical tests were done in 1934, but no development resulted from this work.

Jan 1, 1990

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By F. L. Kadey

A discussion of fillers would not be complete without allotting adequate time to that unique and different mineral material, diatomaceous silica. Historical references to its use challenge the aesthetic aspect of man's curiosity; whereas modern scientific tools have provided a dimension of measurement that has motivated many of its more recent applications. A brief review of what is already known is in order. The diatom is a unicellular, plant-like, microscopic organism, related to the algae1. Its natural function appears to be that of a food for other marine or lacustrine organisms, The diatom's "claim to fame" from an industrial viewpoint is dependent on the fact that it secretes an opaline siliceous skeleton that must survive, chemically and structurally, the geologic processes that caused its formation in the first place; its subsequent demise, burial, consolidation, and alteration; and finally, its ultimate exploitation by man--in somewhat that order. In addition to its siliceous nature, the skeletal structure of the diatom possesses a variety of shapes, patterns, and sizes that have not only been the intrigue of microscopists for decades, but have served to set diatomite apart as an industrial mineral; and have reserved for it applications that cannot be satisfied by any other material. Its chemical inertness, its intricate structure, and its intrinsic hardness-coupled with fineness and friability-- are generally known and have accounted for its application in a wide range of filtration and filler uses. The increasing use of the electron microscope has considerably expanded our knowledge of heretofore unseen secondary and tertiary structure of submicron dimension in the diatom valve. The development of electro-sensing methods of particle size measurement which seem to supersede sedimentation and microscopic techniques has portrayed size distribution in a more realistic light. Interest in the surface chemistry of these silica structures has further strengthened our understanding for certain uses. Thus, new tools and ideas have made possible the introduction of diatomite into such sophisticated technologies as that of chromatographic supports, its improved utility in paint applications for the control of gloss and sheen, and its usefulness in the entirely new concept of "Dry Acid Concentrates." Each of these applications has been discussed elsewhere before people particularly interested in analytical chemistry, in paint, and in liquid handling, respectively, where the diatom has been a means to an end. The emphasis here, before the mining fraternity, however is on diatomite as a raw material with reference to the uses mentioned above. It is therefore toward an awareness and understanding of diatomite properties pertinent to these newer filler applications that this paper is directed.

Jan 1, 1967