Search Documents

By Joseph M. Keane

A number of innovative techniques exist for solving heap leaching problems in special situations. Some of these techniques have been successfully applied and others await an opportunity for application. Discussions in this paper will deal with gold heap leaching under severe thermal conditions, in tropical rainfall circumstances, in the absence of fresh water, and in other situations removed from the ordinary. CLIMATIC CONSIDERATIONS The success or failure of precious metal dissolution operations may be strongly dependent upon proper attention to the influence of climate. A few examples are given in the following paragraphs.

Jan 1, 1987

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978

By C. A. Fleming, K. W. Sarbutt, P. K. MacPhail

The SART process has been developed for Teck to treat bar­ren solution from the cyanidation/CIP process that has been developed for the Lobo-Marte project in Chile. The objective of the process is to recover cyanide in a form that is suitable for recycling to the leaching part of the process. The Marte and Lobo ore bodies require a dosage rate of about 2 kg/t NaCN, of which only 0.5 kg/t is truly consumed (as thiocyanate, cyanate and ferrocyanide species). The remaining -1.5 kg/t is present as cop­per cyanide (-1 kg/t) and free cyanide (-0.5 kg/t), and is poten­tially recoverable and recyclable. SART is an acronym that describes the unit operations in this cyanide recovery process; namely, .. Sulphidization .. Acidification .. Recycling of precipitate " Thickening of precipitate The basic chemistry has been applied previously, and has also been the subject of two patents (American Cyanamid Company, 1965, Potter et al., 1986). The process involves the conversion of all free and WAD cyanide in solution to hydrocyanic acid by acidification of the tailings solution to pH :s,4, and the conversion of all copper in solution to cuprous sulphide (synthetic chal­cocite) by the addition of a sulphide salt:

Jan 1, 1998

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By X. Zhu, L. Chen, R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study was to develop a suitable flowsheet to extract rare earth elements (REEs) from coal ash. Only the findings from the first part of this study is being reported at this time. A total of fourteen coal samples of different ranks were examined for REEs concentration. An anthracite coal sample, originating from Pennsylvania having more than 700 ppm (in the coal ash) was selected for the REE extraction tests. The experimental program completed so far included high temperature leaching using nitric acid, followed by the solvent extraction tests. A 4x2x2 experimental design was used to conduct a total of thirty two high temperature leaching tests by varying acid molarity (at 4 levels), solid content (at 2 level) and leaching time (at 2 level). The highest LREE (light REE) recovery of 90% and HREE (heavy REE) recovery of 94% were obtained from the most optimum leaching test condition while maintaining the impurity recovery to the leachate at less than 40%. Solvent extraction experiments were conducted to recover the REE’s from the above leachate solution using a variety of organic extractants including, TBP, Cyanex, D2EHPA and their combinations. D2EHPA was found to be the best extractant during this SX text series providing nearly 99% recovery of REEs. INTRODUCTION The demand for rare earth element and other strategic metals (REM) in the world is rapidly increasing due to their use in a variety of high technology applications. More than 100,000 tons of rare earth oxides (REO) are being used worldwide on an annual basis. However, we have less than 10% of the world reserve of rare earth element (REE) mineral deposits in the US. More than 60% of rare earth oxide (REO) was imported to the US from outside (mostly from China) in the year of 2013. However, China’s institution of export quota has significantly reduced the supply of REMs to the U.S. Hence, new ways of producing REM and/or finding substitutes for those metals for the high-tech applications need to be invented/discovered in a timely manner. Coal Combustion Byproducts (CCBs), which are discarded as waste materials in most cases, are known to contain REEs (in low concentration) that could be extracted using a suitable process flowsheet. This may be a worthwhile route to pursue considering the short supply of REMs and the abundance of coal ash in thousands of ash ponds in the US. On an annual basis, more than 110 million tons of Coal Combustion Byproducts (CCBs) are being produced while satisfying our nation’s need for electricity (ACAA, 2014). However, less than 50% of these CCBs are being successfully used in various applications and the remainder is being dumped as waste materials in the landfills and ash ponds."

Jan 1, 2017

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By Jon C. Yingling

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will be intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder throughflow to avoid production bottlenecks.

Jan 1, 1992

By Fred V. Carrillo

California was the leading state in industrial mineral production value with an estimated value of nearly $2 billion. In total value of U.S. non-fuel mineral production estimated for 1992 by the U.S; Bureau of Mines, California ranked second; 81 % of California's total production value was derived from industrial minerals. California led all other states in the production of boron minerals, portland cement, diatomite, calcined gypsum and construction sand and gravel, and ranked second in potash and soda ash production. California's five leading industrial minerals in terms of value were portland cement, construction sand and gravel, boron, crushed stone, and soda ash. California had 13 additional industrial minerals production with reported sales of over $1 million including; industrial sand and gravel, magnesium compounds, lime, salt, potash, natural sodium sulfate, clay, feldspar, crude gypsum, pumice, dimension stone, calcium chloride and perlite.

Jan 1, 1995

By William Gleason

"Once the primary fuel source for the United States and the economic backbone for communities from Appalachia to Wyoming, coal has been on a steady decline since the mid 1990s, and is now at the center of political debate in the United States.The political spectrum of the United States is divided on the future of coal and its place in the energy sector. The coal mining industry and the communities that rely on coal have increasingly been pitted against forces that wish to regulate coal to the history books.In 2008, President Obama launched what many have called his war on coal, and during his eight years in office, he pushed through numerous pieces of regulations and legislation and that he said were aimed at reducing carbon emissions, but that others viewed as direct assaults on the domestic coal industry. Obama led the United States delegation to Paris to sign the Paris Accord in 2016, a 196-country agreement pledging that the United States would do its part to reduce carbon emissions. His administration also instituted clean air, power and water regulations that added extra environmental burdens to many industries, but perhaps none more so than the coal industry.In this month’s lead feature, “A study of U.S. coal mine closures since 1994” (page 18), the impact of the war on coal, and other factors, can be seen in text and figures. Author Jacob Brinkman and coauthors Jay Schafler and Catherine Johnson scoured the data of the U.S. Energy Information Administration (EIA) and the U.S. Mine Safety and Health Administration (MSHA) to show how coal production and mines have been impacted since 1994 and how the years 1994 to 2000 and 2008 to 2016 were particularly hard on the industry.For example, in 1994 there were 2,354 coal mines in the United States. Currently, there are 1,035 mines in operation.In 2016, then candidate Donald Trump promised to end the war on coal and to put coal miners back to work. In 2017, President Trump has followed up on those promises. He announced plans to withdraw the United States from the Paris Accord, signed an executive order designed to undo the Clean Power Plan put in place by President Obama, halted the research on the health effects of mountaintop removal coal mining, directed the U.S. Environmental Protection Agency (EPA) to revise the guidelines of waste water from power plants and has touted that more than 1,000 coal miners have returned to work since he was elected."

Jan 9, 2017

By James T. Finley

Profit, product quality, speed of operations, reliability, operator confidence, safety and environmental improvements have all been enhanced as a result of the recently completed maintenance, renovation and construction program at Crown Central Petroleum Corporation?s (Crown?s) coke calcining unit at its Pasadena, Texas refinery. (Figure 1) BACKGROUND The calcining unit was built in 1969 - 1970 and has been operated continuously. Approximately 400 to 500 TPD of high quality metallurgical grade coke is manufactured, stored, and shipped to consumers. About 1/2 of the feed stock to the calciner is manufactured in Crown's coking unit and the remainder is received, via barges, from various sources. The green coke is off loaded from the barges with a conventional grab crane that discharges into a small travelling hopper over a conveyor belt that feeds a radial stacker, which forms a stockpile on the ground. The green coke, from the coking unit at the refinery, is moved to the calcining unit with front end loaders. Reclaiming from the stockpiles is also done with front end loaders. The coke is primarily handled by covered conveyor belts. The finished product is stored in steel silos and can be shipped via railroad cars, but the majority of it is shipped out in ocean going bulk carriers. Maintenance work in the calcining unit is performed by Crown's refinery maintenance department on an as needed, on call basis.

Jan 1, 1983

By J. G. Davis

Continental Oil Company has spent over four years of research on the fundamentals of potash solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well mining systems were studied in the field work. The current paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test. The potential economic value of solution mining has been recognized for many years, and applicable United States patents date back into the past century. Principal advantages of the process over conventional mining include (1) the use of drilled holes and solution techniques in- stead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths.

Jan 1, 1969

By R. Mulyanto, M. Siray, A. Parhusip, F. Hartono

"PT Freeport Indonesia is preparing the Deep Mill Level Zone (DMLZ) mine to be the successor of the currently operating Deep Ore Zone (DOZ) mine. The DMLZ is block cave mine situated 500 m below the DOZ mine and approximately 1600 m depth from surface. Both of the block caving mines require draw point construction in the extraction level to extract the ore from caved area above. Learning from the experience in DOZ, the construction & maintenance of draw points in the production panels is a significant challenge in supporting consistent production.The average DOZ draw point construction duration is approximately 46 shifts per draw point. The time frame for construction is dependent on several variables; availability of the conventional forming system, material availability, and development tolerances. The repair of concrete floors and lintel sets causes production downtime. Reviewing the old DOZ draw point design, there is an opportunity to increase constructability, durability, and reliability of DMLZ draw points. This paper discusses how the DMLZ has improved draw point construction productivity and is on track to significantly reduce costs whilst increasing the quality by using the Six Sigma Improvement Method.Introduction The DMLZ Mine is part of the PT. Freeport Indonesia (PTFI) future Expansion to its underground mining complexes. It is the fourth vertical lift in the East Ertsberg Skarn System (EESS) deposit (Figure 1).Currently, it is under development phase.The DMLZ mine will be a block cave mine using an advanced undercutting method. The DMLZ extraction level will be approximately 1,600 meters below the surface on the 2570 level with column heights of roughly 500 m. The Undercut is on 2590 level, some 20 meters above the extraction level."

Jan 1, 2016

By L. Alan Weakly

The Powder River Basin is the largest strippable reserve of compliant coal in the United States. It is the mother lode, for this Basin is currently supplying 25 percent of the coal produced in the US annually. This paper updates what has happened in the Basin since 1993 in terms of increased production, higher productivity, changes in mine ownership, safety statistics, new equipment, latest coal technologies, and electrical deregulation ramifications.

Jan 1, 1998

By Robert L. Bates

In this paper I use the term "industrial minerals" in its broad general sense, and I distinguish two main groups. The first consists of the bulk materials, characterized by low unit price, nearness of deposits to markets, relatively simple methods of extraction and processing, and a tendency to be closely related to the construction industries. The second group includes those materials valued for exceptional purity, or for some special property such as hardness, immunity to acids, or dielectric strength. These materials are produced in smaller amounts, at high unit values, from deposits notably restricted in. distribution; and they require more or less sophisticated methods of production and beneficiation. The applications of this second group are not closely tied to any particular part of the economy. From the way in which the commodity committees of the Industrial Minerals Division are set up, I take it that the chief interest of most members is with the first group of materials mentioned above. Hence this paper will deal mainly, though not exclusively, with such bulk commodities as sand and gravel, clay, and stone. The first word in the title of the paper also requires brief explanation. It is here given a threefold interpretation. First is the role of the industrial minerals themselves in industry; this would probably be taken as the conventional meaning of the title* The second is the role of the industrial-mineral producers as citizens of the community. The third is what may be called the scientific role of these producers.

Jan 1, 1964

By R. Bruce Thorndycraft

This paper will describe several modifications to design of con­ventional oxide gold heap leaching. They are targeted at reduc­ing costs and simplifying heap operations. These modifications were conceptualized during consulting work on over 90 differ­ent heap leaches. In 1995, a unique opportunity arose to imme­diately apply all of these design concepts to the permitting and construction of a new facility at the American Girl Mine in southeastern California. American Girl Mine has operated since 1987. In April 1995, the mine faced a situation with grave consequences for cash flow. Approval for mining of a new ore zone, Oro Cruz, had just been granted, after lengthy delays by California regula­tors. All existing pad space would be filled by October. Only 6 months were available, and new pad siting and design were still undecided. Permitting of a new pad had not begun. Options were quickly reviewed. A strong criteria for pad site selection and design was ease of permitting. There was also a strong desire to install a system that would achieve better met­allurgical recovery and reduced operating costs, compared to previous heaps at this mine. One site offered the best chance for rapid permitting. It was the site of the original 1987-90 heap leach. This already dis­turbed ground contained 1.6 million tons of heaped ore. The old heap had just completed detoxification and was about to be signed off as a Group C waste, ready for reclamation. Instead of recontouring and revegetating the old heap, which the reclamation plan anticipated, we offered BLM and the County something even better. We proposed to off-load much of the detoxed old heap, and reuse the space. The off-loaded material would be back-filled into the original open pit, imme­diately adjacent. While the footprint of the proposed new pad was much larger, the reuse of disturbed ground, and backfilling of the open pit, had very strong appeal to the regulators. Our permitting strategy included the technical design of the proposed new facility. Many of the new design details also appealed to the regulators, particularly the "zero active ponds" concept.

Jan 1, 1996

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By Merwin Bernstein

Peru has been an important source of metals since Aug. 29, 1533. On that day Francisco Pizarro took charge of the 24 t (772,000 oz) of gold and silver that constituted Atahualpa’s ransom. At today’s prices, the value of that booty ranges between $100 and $150 million, depending on the proportion of gold to silver. Since then, Peru’s silver and gold production has been legendary. Current mine production Most of Peru’s metals are mined from the Andes Mountains and its foot-hills. The Andes run the length of the country parallel to the Pacific coastline from Ecuador to Chile, a distance of nearly 3000 km (I 875 miles). They are about 300 km (187 miles) wide and much of the range is more than 3000 m (9900 ft) in elevation. High plateaus (altiplanos) occupy a large part of the range. Both flanks are rutted by large valleys and canyons. Many of these peaks are prodigious. which make road building expensive and adds to the cost of mining.

Jan 1, 1993

By John Hughes

Fundamental to the use of rotary bit drilling equipment for oil and gas drilling is the requirement to maintain a cooling and lubricating environment for the bit and a means of conveying the cuttings from the drilling operation to the surface. The vast majority of such functions are provided for by the use of water based drilling fluids, commonly known as the drilling mud. One of the basic constituents of drilling mud is bentonite, a montmorillonite clay. Bentonite, when mixed with water at approximately 6% solids, will produce a fluid which has several important features in connection with its role as a drilling mud:

Jan 1, 1983