Search Documents

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By A. D. S. Gillies

The provision of a suitable working environment in deep level mines requires the accurate prediction of the ventilation heat load. Mathematical models for predicting strata heat load have been under development since the 1930's and 1940's. Computer models for predicting this and other mine heat sources have been developed and refined over the last 20 years. Some empirical studies have occurred and there is an increased emphasis on the importance of underground studies. Any theoretically or empirically determined predictive method must of necessity make assumptions. Underground space with its irregular configurations and rough wall surfaces cannot be described by simple mathematical expressions. Some heat loads, such as machinery, may occur intermittently while others such as the influence of water evaporation are very difficult to quantify accurately. Current popular models for predicting mine heat load have been surveyed. In testing some of these it is often found that each estimates significantly different quantitative values for the expected load in a particular underground space under study. These differences are explained by the assumptions, simplifications and omissions implicit in each of these models. It would be easier to estimate conditions at any point if heat flow into mine air passageways could be described by simple equations with associated statistically-based confidence ranges. Use of probability distributions to indicate confidence ranges allows any heat level estimate to be expressed as a range of values with limits for maximum and minimum expected values. This approach allows many of the limitations of the popular predictive models to be overcome. A heat prediction method using this approach has been developed based on Monte Carlo simulation and tested on mine data from a number of operations. Heat flow levels which can be predicted by simple equations supported by probability distributions allow the engineer flexibility in adjusting a predictive model to the underground characteristics appropriate to the mine site under study. The influence of all heat sources present in the mine opening must be included. Prediction methods must be updated as mining systems and machinery change with time. Heat sources interact with one another and the system must therefore be understood in its entirety.

Jan 1, 1987

By James N. Prudden

Measurable physical characteristics of placer deposits include geological, geomorphological, sedimentological and mineralogical features which produce the complimentary ingredients with which one can formulate an economic evaluation of these complicated deposits within the confines of a well established geological model. Heavy mineral suite composition and character will change downstream from the provenance area and will compliment the related depositional environment. Careful attention to gold particle characterization during the exploration phase can indicate new source additions, enhance deposit evaluation methods and greatly assist in maximizing metallurgical efficiencies. Failure to recognize and measure these important features very frequently leads to frustrated and unrewarding placer evaluation goals. Increased general acceptance of sedimentology in the gological appraisal of ore bodies has progressed into the science of clastic sedimentalogy using measurable parameters to evaluate minable units. This branch of geology has developed as a tool in locating, defining, and mining alluvial concentrations of valuable heavy minerals. The repeatedly successful application of this valuable tool in conjunction with other classical geological methods can be directly related to the development of a geological model which formulates the distribution of detrital gold. This use of multiple geological techniques permits the transfer of routinely derived data to management. Standardized nomenclature permits the transmission of uniform information thereby promoting credible property evaluation. This approach enables organizations to critically assess large numbers of potential mining targets for definitive feasibility studies. Sedimentology must play an integral role in the evaluation of any alluvial deposit. The sampling problems associated with particulate gold are well known and frequently cause perplexing evaluation problems. Consequently, properly directed and executed

Jan 1, 1987

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992

By J. Kretschmann, O. Drusche, S. Krause

Mining companies are caught between the growing international relevance of ESG (Environmental, Social and Governance) investments and the need to secure their “social license to operate” by considering the needs of their stakeholders. In the search for sustainable business models, the concept of the circular economy (CE) is gaining momentum among practitioners and scholars, as it enables the creation of shared value and thus strengthens the trust of investors and stakeholder relationships. However, there is a lack of a sectorspecific CE framework providing guidance to decision-makers in evaluating promising activities. A gap, which this contribution aims to address.

Mar 2, 2022

By James D. Cooper

Technologic advances in materials utilization during the past two decades have brought is a long way toward the point where we can make the products we need from the materials we have readily available. Notable examples are the synthesis of diamond, zeolites, quartz crystal, mullite, and mica, and the development of phosphate bonded tale. Two of these--zeolites and mullite--involve the use of clays. There is little reason to doubt that equally important advances will be realized in the next decade, and that clays will play an important role in the developing materials technology. Indeed, the stage is already set for many of them. This discussion is concerned primarily with the high quality, relatively high priced clays, kaolin, bentonite, fuller's earth and ball clay. The first three have enjoyed demand growth rates over the past two decades which on the average exceeded the growth rate for the economy as a whole. There are indications that demand for ball clay will be growing at a faster rate in the future.

Jan 1, 1970

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By P. McGrath

From the mid-1980s through 1997, Echo Bay Alaska evaluated reopening the historic Alaska-Juneau (AJ) gold mine. Their original proposed project underwent numerous modifications in order to minimize the potential for significant environmental impacts. One of the major modifications involved changing .the tailings disposal method from a conventional tailings impoundment to submarine tailings disposal (STD). In 1995, the U.S. EPA began work on a Supplemental Environmental Impact Statement (SEIS) to assess the impacts of the STD proposal. Key features of the STD impact assessment included fate and transport modeling to determine the extent of tailings deposition and the use of ecological risk assessment to predict marine impacts during deposition and ecosystem recovery following STD. A key feature of the SEIS regulatory process included a rulemaking proposed by EPA to exempt the AJ tailings from effluent regulations. Critical to success in moving the project forward was early development of an interactive working relationship with other regulatory agencies and the public.

Jan 1, 1998

By O. W. Kamper

To most of you present here the word "refractories" is not new and you are familiar with the materials and use. To many people though the question is asked, "What are refractoriness and what are they used for?" Refractories are non-metallic products which are so resistant too melting at very high temperatures that they can be used for building or lining furnaces of all kinds. A large variation occurs in the size, form, and composition depending on the service for which they are intended. They are made from a wide variety of raw materials, of which fire clay and quartzite are used in largest quantities. Other refractory raw materials include magnesite, chrome, diaspore, bauxite, kyanite, sillimanite, olivine, zircon, and many others. Most of these are assembled from-widely-'separated points in the United States while others come from the far corners of the earth. Chrome is imported from the Philippines and South Africa, and, to a lesser extent, Turkey and Greece Kyanite and sillimanite come: from India and bauxite from the Guianas. And there's "magnesite from brines," produced in chemical plant's by treatment of sea water or inland deep-well brines with hydrated lime. The proportion of magnesia available in sea water is so small, less than one pound from 500 pounds of water,, that millions of gallons must be pumped and processed each day in a sea water magnesite plant. The realm of refractory raw materials, therefore, is very extensive and continues to grow because of the endeavor to find-better raw materials from which to produce better products for refractory service.

Jan 1, 1960

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By Thomas F. Evans

Niagara Mohawk, like other northern coal users, has long experienced increased costs during winter months as a consequence of handling frozen coal. These costs include operating labor, maintenance labor and materials, equipment rental, fuel for thawing, demurrage, carrying costs for excess coal inventory and substitution of higher cost electrical generation for lost production capacity. In the winter of 1978-79, limited trials of several coal freeze conditioning agents were made to determine whether these would provide a cost-effective means of reducing the problems of handling frozen coal. Since these trials were generally effective, the Coal Purchasing Department arranged that all rail coal received during the 1979-80 winter from early December to mid March would be treated at the mines during loading. Inasmuch as the treatment costs are themselves appreciable and our various coal suppliers made a variety of choices of chemical supplier and equipment for application, an attempt was made to evaluate the unloading performance of each train received at the two generating stations which use coal as an aid in the future optimization of the use of freeze conditioning agents. These stations also receive coal by truck but this coal is not treated because of the short hauling time. The C.R. Huntley Station in Tonawanda, NY has a capacity of 800MW and burns about 5000 tons of coal per day during the winter months. The coal is primarily from central and western Pennsylvania but one source in southern Kentucky is also used regularly. Most of the Pennsylvania coal is washed and the fines are thermally dried. The coal is delivered in unit trains made up of mixed cars of 60, 75, and 90 ton capacity. Time between loading and arrival at the station averaged five days and ranged from three to eleven during the 1979-80 winter season.

Jan 1, 1980

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma type iron-formation constitute low grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron-formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 meters thick occurring separately or with other iron-formation facies are associated with cherts, carbonates, shales, turbidites, tuffs and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher grade deposits derived by secondary enrichment processes.

Jan 1, 1982

By Garry W. Warren

The electrochemical oxidation of chalcopyrite in the absence of-a chemical oxidant was studied in ammonia/ammonium sulfate solutions by anodically polarizing electrodes prepared from massive chalcopyrite. The effects of pH, cupric and ammonia ion concentration were systematically evaluated. Kinetic parameters were obtained from the anodic charge-transfer regions of the anodic polarization curves. Increasing ammonia and hydroxyl ion concentrations increased the rate of oxidation. A mechanism is proposed which explains the first order dependence of (NH3) and (OR) associated with a single electron transfer process. An empirical relationship which accurately describes the dependence of the rest potential (i.e. zero current potential) on solution composition is also given.

Jan 1, 1978

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993

By Langtry E. Lynd

The titanium dioxide pigment industry in the United States has always relied to varying degrees on imported titanium concentrates. Dependence on foreign ilmenite was especially high (generally over 85% of consumption) until 1942, when large-scale U.S. production of ilmenite began, and has since ranged from 12% to 47%. Rutile import reliance was generally in the 45% to 80% range until the early 1960's, when increased use in the chloride pigment process raised dependence on imported rutile to over 90% in most years since 1963. Import reliance of zircon, obtained almost entirely as a byproduct of titanium mineral production, has generally ranged from about 30% to 65% of consumption. This paper will examine the history of U.S. sources of these heavy mineral commodities, and will discuss the potential U.S. future supply in view of changing industrial uses and processes and the anticipated development of new heavy-mineral-sand processing operations, such as those at Richards Bay in the Republic of South Africa and in Sierra Leone.

Jan 1, 1978

By D. W. McGlashan

[Comideha;tion o 4 chyakd- chem and aLtuctund phopetttiu o auRdide nm&, The in~o/uncction gained h ;to be uned ;to iM;tmph& ( I! dnukey bho hen mind-aundacu , ( 2 ) modidicakio~n 06 ;the minmd n~tdacu, and (3) eac;tiom at ;the mind adac fnom ;thu e baic din oipfina, concep;tc, wLth hegattd ;to .the changen kha;t awtgacu undehgu, heac;tiom kha;t might take place, ,the geom&y 04 ;the inkmduce, ;the nkde 04 diddmenk &om and iom in ;the intmdace, and okhm phyaicd and chemicd pttopemXu od an intmdace mun;t be developed, weighed and appfied. The au/tho~ ded wah thue concep;tud connidmatiom @om which hypokhuu me n& ko denchibe khe envhomenkd-ivttadaciae hela;tiomhipa doh nevmd nddide minettah, The ch&enge and moltivation in khe hu eattch h in a henhe a deattch doh baic dad and helcctiomkipa needed doh accompfi he&.] INTRODUCTION Qualitative and quantitative explanation of particulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occur- ring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc. on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental- interfacial relationships for sulfide minerals.

Jan 1, 1968