Search Documents

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By F. L. Pirkle

A heavy-mineral deposit about 1.6 kilometers (I mile) in length and averaging about three meters (10 feet) in thickness is exposed approximately130 kilometers (80 miles) east of Denver, along Interstate 70, in Elbert County, Colorado near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium Ridge. The dominant heavy minerals, accounting for about 70% of the total heavy mineral suite by weight, are ilmenite, garnet, and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan, and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Georgia. Thus, Titanium Ridge provides evidence that heavy-mineral accumulation models for late Cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2011

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By M. Prasad, G. M. Rao, T. C. Rao, A. K. Majmudar

A two-step flotation scheme was employed to beneficiate a low-grade, cherty-calcareous rock phosphate ore from the Jhabua district, Madhya Pradesh, India. In the first stage, apatite and calcite ire floated together to remove silica, and, in the second stage, calcite is floated and apatite is depressed. The reagent scheme consists of sodium oleate, sodium silicate, orthophosphoric acid and sulfuric acid. The effect of reagent dosages on the efficiencies of separtition in each stage was studied systematically. A flowsheet was proposed for the processing of a low-grade phosphate ore containing 12.5% P2O5, 26.5% SiO2 and a CaO/P2O5 ratio of 2.64 (=32% calcite). The proposed flowsheet would produce a composite phosphate concentrate containing 27.2% P2O5, 6.37% SiO2 and a much reduced CaO/P205 ratio of 1.66. The total P2O5 recovery for the composite concentrate would be 73% .

Jan 1, 1996

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

By Verya Nasri, Heather M. Ivory, Kevin Clarke, Eric Cole

Development of the New York City Water Supply System The New York City water supply system serves a population of almost nine million, including residents in neighboring counties. Peak day demands on the system are currently running at about 70 m3/sec (about 1,600 mgd), which is significantly lower than in the 1990s. This trend of reducing demands over the past 25 years, which has been experienced in other major urban centers in the US, is mainly the result of conservation measures and increased cost consciousness on the part of water users. In the long term, demands are expected to once again follow an increasing trend with population growth, so that by the end of the planning horizon of these studies, the year2045, the peak day demand is expected to increase to about 85 m3/sec (2,000 mgd).The system is served largely by surface water sources, regulated by a system of 19reservoirs and three controlled lakes, which are connected to the City by a series of aqueducts, the longest of which is about 87 km (54 miles). The total storage in the sys-tem amounts to about 560 billion gallons, providing a system firm yield of about1300 mgd. The Delaware system provides about 50% of the City’s water, the Catskill about 40%, with the remaining 10% provided by the Croton. The system as a whole, which is shown on Figure 1, has been built up over the past 150 years, and is truly a marvel of engineering. The Catskill and Delaware aqueducts both discharge into Kensico Reservoir, which is a daily balancing reservoir located in Westchester County about 24 km(15 miles) north of the New York City line. The two aqueducts extend south for a further 14 miles to combine again at Hillview Reservoir in the Bronx, which provides hourly balancing storage for New York City system. The Croton aqueduct runs nearby as shown on Figure 2, but does not connect into the two reservoirs. From Hillview Reservoir the water is supplied to the city via three main distribution tunnels, known as City Tunnels 1, 2, and 3. City Tunnel No.1 was developed in the 1920s as part of the Catskill system. City Tunnel No. 2 followed in the 1960s as part of the Delaware system. City Tunnel No. 3 (CT3) is partly under construction and partly in operation, and is being implemented to permit the other distribution tunnels to be taken out of operation for the first time for inspection and maintenance. Presently CT3 is supplied with water from Hillview Reservoir via a large underground valve chamber, the Van

Jan 1, 2007

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By I. A. Kunasz

This paper is not intended to review and re-state general information on lithium, but rather to analyze the paradigm that has caused such a rapid rise in lithium production and the development of new lithium producing centers. Details on pegmatites, brines, concentrate and chemicals are amply covered in a number of publications ? SME?s Industrial Minerals and Rocks, Industrial Minerals, Roskill and a host of other publications. There is no question that the latest interest in lithium has been driven by the potential development of the electric car. This stimulus prompts one to recall two symposia: 1. ?Lithium Resources and Requirements be the year 2000?, organized in 1976 by the U.S.G.S. in Denver (1) and the sequel 2. ?Lithium ? Needs and Resources? at Corning, N.Y. (2).

Jan 1, 2011

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By K. P. Black, G. W. Sevick, D. E. Hockley, K. S. Sexsmith, J. T. Chapman

Mineralogical analyses of carbonates in depyritized tailings and pyrite concentrate (from depyritization of the tailings) were completed as part of the tailings characterization for the Crandon Project, a massive sulfide deposit in northeastern Wisconsin. The mineralogical study was designed to determine the proportion of calcium and magnesium carbonates, and therefore the effective buffering capacity of carbonates in the tailings. The depyritized tailings are net acid consuming and will be stored in a surface tailings management area. The pyrite concentrate is net acid generating and will be used as backfill in the underground mine workings. The majority of carbonates in the depyritized tailings were ferroan dolomite containing 10 to 15% iron (by weight) and lesser amounts of siderite and magnesian siderite. The proportion of calcium and magnesium-rich carbonates corresponds to several independent tests of carbonate neutralization potential (CO3-NP) availability. The pyrite concentrate had less CO3-NP, indicating segregation of the carbonates during pyrite flotation. These carbonates reported higher iron contents, consistent with the relatively lower availability of CO3-NP in the pyrite concentrate.

Jan 1, 2002

By S. G. Malghan

This paper describes uses of sodium sulfide in the flotation of oxide and sulfide minerals of copper, lead, and zinc. The activation and depression effects of sodium sulfide are of particular importance because of their applications with oxidized lead and copper ores. In spite of its industrial importance; however, the nature of the heterogenious reactions between sulfide ions in solution and the surface of oxidized minerals has not been fully understood. Hence, proposed mechanisms of the sulfide action in flotation, methods of measuring and monitoring of sodium sulfide in flotation pulps, and variables influencing the sulfide addition are analyzed. A review of recent studies shows that sodium sulfide addition to flotation pulps can be monitored and hence the optimum dosage controlled using the platinum and/or sulfide specific ion electrodes. The use of these electrodes for improved reproducibility of bench-scale experimental data and plant implementation of laboratory results is described.

Jan 1, 1985

By M. Javier

This concept paper is presented in the hope of raising the awareness of mankind on the necessity for its peaceful coexistence with nature. It is a food for thought. It takes compromise and sacrifice of people, who will have to learn to curb their greed and move toward a more organic form of prosperity. A nature-friendly sustainability is first step toward the protection of nature that is critical to the mutual survival of mankind and nature. People need the resources from the finite earth to survive and nature needs the prevention of human destruction in order to continue to regenerate and provide. The contemporary notion of sustainability is self-serving. It serves the interest of industry by camouflaging itself to look like nature?s protector. The ?sustainability? concept presented in this paper aims to extend the longevity of the utilization of the limited natural resources for many generations to come. It is an important, responsible first step in creating a healthy sustainability concept that, when implemented, extends the longevity of mankind by the most efficient use of the finite resources on this limited Planet Earth, all the while taking into consideration the increase in anthropogenic activities due to exponential human population growth. This new definition of ?sustainability? has completely different characteristics than its contemporary versions. Nature has its own destiny, rules and principles. Being a part of nature, human society depends on it for survival and must play by its rules and never the other way round as in its initial pretensions. Society should not try to humanize nature, but rather to respect the rule of the nature in a peaceful way of co-existence. When implemented, this new concept of sustainability aims to affect the designs of engineered structures and revolutionize the recovery methods and processing of natural resources, such as mineral resources in the most efficient manner. Finally, this paper intends to stimulate critical thinking and initiate serious discussions aiming at producing a general consensus for the best definition for human society to not only enrich, but to extend its existence. Thus, the spirit of this new definition is pro future generations and environment. KEYWORDS: Sustainability Definition, Nature, Geomímic, Deproduction.

Feb 27, 2013

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.