Search Documents

By Richard J. Fantel

This paper addresses the impact of declining world rutile resources upon the production of titanium products and their asso¬ciated costs. Titanium is used primarily for the production of pigments; in its metal form it is considered a strategic and critical material to the U.S. defense and aerospace industries. There are two major mineral sources for titanium: ilmenite and rutile. Both these mineral types can be used to produce titanium pigments. Only high grade titanium concentrates, such as rutile, high-grade ilmenite, and synthetic rutile (which is produced through further processing of ilmenite), can be used in the production of titanium metal. This paper draws upon the data and analyses of a recent Bureau of Mines Minerals Availability Program appraisal that evaluated the international availability of titanium from market economy countries. The paper will show that production from economic rutile mines will decline sometime after the turn of the century and that rutile shortages could be alleviated by production from other high-grade titanium resources such as higher cost rutile deposits and anatase deposits, or through an increase in world synthetic rutile capacity.

Jan 1, 1984

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By R. H. Church

The Bureau of Mines' Tuscaloosa Research Center has developed a field test unit (FTU) which dewaters mine and/or mineral processing by-product slurries. The feed material (by-product slurry) is mixed with a known quantity and specific type of synthetic polymer (usually a polyacrylamide) to induce flocculation in a continuous operation. The flocculated material passes over a specific number and size of slotted stationary screens which separates the flocculated solid material from the "clean" water. The "static screens" are positioned at a fixed angle to maximize flow capacity and capture of the solids content. An investigation was conducted at an industrial crushed stone operation located near Birmingham, AL, to determine if the Bureau's FTU could successfully dewater the waste slurry generated during grinding and sizing operations at this facility. The investigation showed that waste slurries could be dewatered to 50 pct solids, at a polymer cost of approximately $0.85/ton of dry solids treated, and resulted in approximately 85 to 95 pct solids recovery. The dewatered material continued to consolidate and reached 69 pct solids in 24 h. Presently, the waste slurry generated at this facility is discarded into impoundments. However, this research has identified the recovered waste as an economically marketable product.

Jan 1, 1994

By Stuart Hammer

The mining industry has seen a flurry of merger and acquisition activity of late. Rising metal prices, increased spending on infrastructure in developing nations and the growing demand for companies to diversify have helped fuel M&A activity in this industry. Many analysts believe that the robust M&A activity will continue, particularly if the demand for mineral resources in India and China remains strong. Because prospective purchasers need to evaluate the various risks confronting target companies, acquiring mining companies requires a considerable amount of due diligence. Of these risks, environmental risk is critical and warrants significant analysis. The failure to properly assess environmental risks associated with remediation, reclamation, compliance or litigation can undermine the transaction. Such assessment is a difficult endeavor, however, due to several challenges that companies face when assessing environmental risks. To make matters more complicated, despite these challenges, many sellers ask buyers to assume all environmental risks with limited post-closing indemnification rights. This article addresses the most significant issues that commonly arise when conducting environmental due diligence and allocating environmental risk in connection with M&A transactions in the mining industry.

Jan 1, 2008

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

Joy Mining Machinery has developed a new generation of ultra-heavy shields for Anglo Coal Australia?s Moranbah North Mine in the Bowen Basin region of Queensland. These are the largest two-leg longwall shields yet produced by Joy. The longwall at Moranbah North posed a number of challenges, among them a thick, inclined, sometimes undulating seam with increasing depths. The result of this was the need for larger, heavier, more powerful roof supports. Knowing that future longwalls would be going deeper, mine management determined that shield yield ratings of at least 1,750 t (1,930 st) was what would be required.

Jan 1, 2011

By J. Hanna, I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pHs without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35% to 38% P2O5, 0.8% to 1% MgO) with high recoveries (80% to 85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P2O5 and 0.8% MgO, with a P2O5 recovery of 76%. A concentrate obtained from the western US phosphate ore from Utah assayed 30% P2O5 and about 1% MgO, with a P2O5 recovery of 89%.

Jan 1, 1988

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By Chee Theng

"Getting minerals out of ores is messy, but mineral processors learn to have fun with it. Celebrating the innate joys of the industry was the theme of this year’s Colorado MPD Conference. At the same time, attendees dug deeper for insights into problems that continue to dog the community, including tailings dam crises, water resource challenges, and a dwindling number of academics to teach and train the workforce (see box).Tailings dam crisesMatt Fuller of Tierra Group International Ltd. brought some of the audience to tears with his impassioned talk on “The Infamous Legacy of Upstream Tailings Dams,” which won the conference’s Lou Cope award for best paper. The talk was especially poignant coming on the heels of the January tailings dam failure in Vale S.A.’s Córrego do Feijão iron ore mine in Brazil, the latest in a series of catastrophic dam failures over the past decade that includes the Fundão dam failure in 2015.Noting that the two dams share a common characteristic — both are upstream tailing dams — Fuller explained the three basic dam construction methods and why certain upstream tailing dams are susceptible to failure (Fig. 1). The downstream, centerline and upstream methods denote the direction the centerline of the dam crest moves with each successive raise in elevation of the dam. With the downstream dam, the foundation for future raises is essentially the same as that of the starter dam, he explained. With the centerline dam, half of the dam is constructed on the same foundation as the starter dam, and with the upstream dam, each successive raise is built out over the top of the tailings.“Downstream dams are expensive to build because each successive raise is bigger, so the sustaining capex to build them keeps growing,” Fuller said. Many decades ago, mine owners realized they could construct a starter dam, put their tailings through a hydrocyclone, generate a coarse sand fraction and stack the sand over the top of the tailings to build the next raise. “Then, there is no sustaining capex, it all comes out of operations,” Fuller added. The footprint is smaller, and it is a favorable means of retaining the tailings."

Jul 1, 2019

By Robert M. Abrams

The passage of an ore pulp through the froth flotation process results in the production, after dewatering, of a finely divided concentrate. This intermediate product Trust be handled to the subsequent process facilities via belt or other types of conveyors, hoppers, bins, chutes and feeders, and the like, Flotation concentrate has some difficult handling properties such as abrasiveness, sluggishness when moist, or fluidity when dry, These characteristics require the judicious selection or design of handling, equipment and the careful engineering of transfer chutes. It is to the special problems which are encountered in this in-plant handling procedure that this paper is addressed. The methods which will be discussed have beer. developed primarily for the handling of the froth flotation concentrates of copper, leap, and taconite iron ores, but may be generalized, with appropriate modifications, to apply to other similar metallic concentrate&. The controlled feeding of concentrates frog: bins and hoppers is covered alone with some of the techniques used to transfer concentrates from ore belt conveyor to another. Methods are described for unloading belt conveyors into bins or storage tiles, The reclamation from storage piles is also treated.

Jan 1, 1976

By Donald E. Ralston, A. T. Yu, Richard P. Killmeyer, Peter Phillips, R. W. Vander Laan, John N. Murphy, John R. Messineo, John Peters

Overview Coal production in the first half of 1982 remained near the high levels begun in mid-1981. Production then fell sharply during the latter part of the year due to recession-weakened demand. Even so, 1982 coal production was estimated at 756 Mt (833.4 million st), a record high that exceeded 1980's previous production record of 752.7 Mt (829.7 million st). Though 1982 coal production was substantially below industry expectations, the attained production represented a modest achievement in view of the recession's severity. In 1982, the gross national product declined 1.8%, its worst performance in 36 years. The recession, along with mild weather, improved energy efficiency, and conservation efforts caused the nation's energy use to drop 4.1%. With the iron and steel, construction, and auto industries experiencing production declines, industrial energy use fell 10.8%. The extent to which the nation's economic slump affected coal markets in 1982 varied: • total domestic coal use declined 3.4%; • exports remained strong for most of the year; • electric utility coal use declined for the first time in 25 years; • coal use at coke plants declined by one-third; and • coal use in other industrial sectors stayed surprisingly near the 1981 level. Coal Use Domestic coal use totaled 641.8 Mt (707.5 million st) in 1982,22 .9 Mt (25.2 million st) below the 1981 level. Nearly all the decline occurred at coke plants where use dropped to 37.1 Mt (40.9 million st) in 1982 from 55.3 Mt (61 million st) in 1981. The decline in all other industrial and electric utility coal markets was only 5.3 Mt (5.8 million st). Residential and commercial coal use increased 635 kt (700,000 st) to 7.3 Mt (8.1 million st) from 6.7 Mt (7.4 million st). Power generation decreased 2.3% in 1982, the first year since 1945 that output failed to increase. The decline was due to a drop in industrial demand. Electricity sales to residential, commercial, and other nonindustrial users increased slightly. But coal's competitive position stayed strong. Power generation from oil and natural gas fell 28.9% and 11.7%, respectively. Power generation from coal declined only 0.9%. Among the primary energy sources, coal fueled 53.2% of US electric power generated in 1982, compared with 52.4% in 1981. In 1982, US steel production declined to 66.1 Mt (72.9 million st), the lowest level in 50 years and down from 109.6 Mt (120.8 million st) in 1981. The reduced steel demand forced 13 coke plants to shut down. Coal Exports Coal exports in 1982 totaled 96.4 Mt (106.3 million st), 5.7 Mt (6.3 million st) less than in 1981. Despite the worldwide recession and above normal coal stockpiles in many countries, exports were higher than many expected. This showed the relatively strong US position in international coal trade. The US continued to export near-record coal tonnages despite increasingly competitive influences. These included an improvement in Australia's labor difficulties, the return of Polish coal to Western European markets, and lower oil prices. In 1982, US port facilities were improved and expanded, and more efficient methods for scheduling foreign vessels were implemented. As a result, high volume coal shipments to US ports were routinely loaded and dispatched unhampered by bottlenecks that plagued East Coast ports in 1981. Appalachian coalfield production declined 1.4% from 1981 output and 3.9% from 1980 output. The interior region of the US showed an increase of 7.8% in production. This was primarily because of a

Jan 5, 1983

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By James D. Bennett

Relationships among mine and injured miner characteristics and HSAC's degrees of injury are examined for 91,404 injuries in under- ground bituminous coal mines in the United States from 1975 through 1982. Injury severity varies by the mining system, geographical region, circumstances surrounding the injury, the injured miner's age, whether the miner was using powered equipment, the year which the injury occurred, and the location in the mine where the injury happened. Injury severity is not related to the injured miner's total mining experience, job experience, and experience in the mine in which the injury occurred.

Jan 1, 1984

By David W. Wisecarver

The U.S. Bureau of Mines, in cooperation with U.S. Borax and Chemical Corporation and the Kennecott Copper Corporation, has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of microseismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron Mine near Boron, California, and the Rimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nevada. Microsesimic noise rates in stable inactive mining areas are between 0 and 10 noises/ hour; the rates in stable active mining areas are between 10 and 50 noises/hour; and the rate in unstable areas is as high as 2500 noises/ hour. High microseismic noise rates in the Liberty Pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic tech¬nique is applicable to large pit walls, and that the wide band, wide range microseismic equipment appears to be suitable for open-pit investigations.

Jan 1, 1969

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By Frederick P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian Region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modelled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1979

By W. S. Urbanski, A. L. Devernoe, M. S. Walker

Theory and practice are described for a new processing method capable of precise mineral separations based primarily on differences in particle specific gravities at specific gravity split points from 1.5 to 21.0 and beyond. Separations are analogous to those achieved using rotating heavy media, except that the effective specific gravity of the fluid is created magnetically using a relatively dilute, low-viscosity, water-based magnetic fluid. Results reported here for a large, laboratory flow-through separator include: 1) 99% grade with 97% recovery in single pass separation of a suite of heavy minerals from quartz at I0 kg/h, 14 tph/rm2 of duct cross section, 2) 90% grade and recovery in single-pass separation of mixtures of sand-size, non-magnetic rutile (4.23 specific gravity) and zircon (4.72 specific gravity) at throughputs of 35 kg/h, 47 tph/rm2 of duct cross section, 3) partition curves having Ep90-10 transition widths 5% or less of mineral specific gravities, and 4) essential confirmation of the theory.

Jan 1, 1991