Search Documents

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low-, a medium-, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0 percent ash, as follows: From low-volatile anthracite, 0.7 percent; from medium-volatile coal, 1.0 percent; and from high-volatile coal, 2.3 percent. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0 percent or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a conventional dense-media washing plant.

Jan 1, 1968

By A. V. Castelli

The provinces of Guangxi, Guizhou, Hubei (and most recently Fujian) were the prime exporters of barite during this period. Guangdong and Shandong were exporters too but not major participants. These are all primarily agricultural areas so there existed a sufficient labor force willing to work in the mines to supplement their income from farming. During the early years, barite export pushed the existing transportation systems in these provinces to operational capacity. The mines from which this barite is extracted are located about 250 to 1,400 kilometers from the sea ports. Transportation of the ore from the mines to the ports follows a net-work that includes trucking to various rail-heads where it is then shipped via freight trains to ports for loading into seagoing vessels. in some instances, the barite travels by truck or train to the Yangtze River where it is then barged to an ocean port.

Jan 1, 1990

By G. Reed Marchant

The control systems engineer is often faced with the problem of designing tests or experiments where the cost of obtaining information is expensive. This is true in aerospace as well as in process industries. In these situations the details of test design should be carefully evaluated before any test is executed so that the maximum amount of information is obtained for the effort expended. In recent years there has been a steady trend towards increased automation, In the process industries this has resulted in extensive review of process variables and, instrumentation techniques, development of more accurate system mathematical models, and extensive investments in complex control system as well as completely automated plants. When planning and developing these systems, where each measure of a process variable is usually expensive, it behooves the design engineer to give considerable thought to the details of test design before instrumentation is procured and installed so that the maximum amount of information can be obtained for the expense incurred.

Jan 1, 1968

By Paul Sainato, J. Steven Gardner

Sustainable development is defined as ‘development that meets the needs of the present without compromising the ability of future generations to meet their own needs.’1 There has been considerable debate of late between environmentalists and mining operators concerning the current regulation and operation of mountaintop mining. To those not familiar with the practice, it essentially applies an area mining method to a mountaintop, removing all overburden above coal seams, resulting in full recovery of the resource with the excess or swell spoil material - (rock and dirt) being deposited in engineered fills in hollows to the side (known as hollow fills or valley fills - very similar to highway fills). Because most of the dialogue has been adversarial and mining’s response is perceived to be primarily reactive instead of proactive, a rift in communication and value systems between the two sides has widened. Since 1999, the global mining community has been concerned that there is a disconnect between mining practices and the values of today’s society.3 Working through the World Business Council for Sustainable Development (WBCSD), the International Institute for Environment and Development (IIED) was created to review mining practices in a project entitled Mining, Minerals and Sustainable Development (MMSD) driven by the following four goals:

Jan 1, 2005

By D. Akers, R. Dospoy

Introduction The geological processes that form coal can also concentrate trace elements in the coal. For example, the average concentration of arsenic in bituminous coal (20 ppm) is ten times the average concentration found in all the other rocks that make up the earth's crust (2 ppm). Similarly, other elements, such as antimony, cadmium, mercury and selenium, are more concentrated in coal than in the earth's crust. When coal is burned, trace elements can be further concentrated. Although no new constraints on trace clement emissions were placed on the power generation industry under the 1990 Clean Air Act Amendments, the act does mandate a three-year study of air toxics. Any new regulations aimed at electric utilities as a result of this Federally-mandated study will almost assuredly be very costly-an estimated $1 billion per year. Many trace elements in coal are associated with mineral matter. For example, arsenic is commonly associated with pyrite, cadmium with sphalerite, chromium with clay minerals, mercury with pyrite and cinnabar, nickel with millerite, pyrite and other sulfides, and selenium with lead selenide, pyrite and other sulfides (Finkelman, 1980). There are also cases in which some of these elements are organically bound. Just as both organic and pyritic sulfur can be found in the same coal, the same trace element may be both organically bound and present as part of a mineral in the sane coal. Physical coal cleaning techniques are effective in removing mineral matter from coal and can potentially remove at least some of the trace elements associated with specific minerals, thereby reducing the release of these elements into the atmosphere. Conventional coal cleaning to remove trace elements As part of a project funded by the Electric Power Research Institute, CQ Inc., a wholly-owned EPRI subsidiary located in western Pennsylvania, has demonstrated that large reductions in the concentration of many trace elements are possible if conventional coal cleaning techniques are properly applied. Four examples are given in Tables 1 to 4. In each example, the results shown were generated by cleaning the coal at CQ Inc.'s commercial-scale cleaning test facility. Cleaning results for Upper Freeport Seam coal from Northern Appalachia are provided in Table 1. Data are presented in the table in two ways: as a weight-based concentration (parts per million) and as a concentration per heat unit (grams per billion Btu). Grams per billion Btu is analogous to pounds per million Btu, but avoids the use of numbers with many decimal places. The heat-based concentration provides a better measure of boiler impacts, because the increased heating value obtained through coal cleaning reduces the number of tons that must be burned to produce a given thermal output. Reducing the quantity of coal burned reduces the quantity of trace elements entering the boiler. This raw coal is relatively high in several trace elements of environmental concern, including arsenic, cadmium and chromium. Cleaning provided large reductions in the quantity of arsenic, barium, cadmium, chromium, fluorine, lead, mercury, nickel, silver and zinc. The results for tests with a Powder River Basin coal, Rosebud/McKay, are presented in Table 2. Large reductions in arsenic, barium, cadmium, fluorine, mercury, nickel, selenium and zinc were observed with cleaning. The concentration of chromium increased with cleaning, while lead concentration increased in one test and decreased in another. Table 3 presents test results for Croweburg Seam coal from Oklahoma. Large reductions in arsenic, barium, cadmium, chromium and zinc were obtained with cleaning. Smaller reductions were obtained with lead and nickel, while chromium, fluorine and mercury increased in at least one of the tests. Table 4 presents cleaning test data for Kentucky No.11 Seam coal. In this case, large reductions were obtained with all elements measured. In general, these data indicate that physical coal cleaning is effective in reducing the concentration of many trace elements, especially if they are present in the coal at relatively high concentrations. The degree of reduction achieved is coal-specific, relating in part to the degree of mineral association of the specific trace element and the degree of liberation of the trace element-bearing mineral. The extent of trace element removal also depends on the method of cleaning the coal. Figure 1 is a washability plot, by size fraction, of arsenic vs. ash content for Upper Freeport

Jan 1, 1994

By Craig J. Brown

Despite its great potential utility, ion exchange has only achieved limited application in hydrometallurgy. To a significant extent this is due to the limitations of conventional ion exchange process design as well as the properties of the ion exchange resins themselves. Over the past decade several new ion exchange resins have been introduced with properties that make them potentially very useful for various hydrometallurgical separations. In addition, a novel ion exchange process called Reciprocating Flow Ion Exchange or Recoflo, which has been employed in the metal finishing industry for the last dozen or so years for chemical recovery and effluent treatment, has been shown to offer a number of unique and significant advantages over conventional I.X. technology.

Jan 1, 1984

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By Jr. Koch

Since 1882, world zinc production has increased. In contrast, United States zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the United States, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in United States production are due to economic, not geological, factors. Recent exploration has located large mineable ore bodies; additional deposits will undoubtedly be found in the strata-bound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the United States is in an early stage of the production cycle for zinc. Of major mining districts in the United States, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district.

Jan 1, 1980

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By Edwin R. Phelps

Good morning ladies and gentlemen - today I am in an enviable position for two basic reasons - No. 1, since I am first on the program, the audience should start out awake because those that partied too much last night are still asleep, but in their room, not here. No. 2, since copper, iron, and mining technology are not competitive, the veracity of my statements will not be questioned. Most such meetings I attend are based on the subject of energy and the coal industry does have competition from oil, gas, hydro, and nuclear. However, to counteract this advantage I am the usual engineer with a limited vocabulary by schooling, and the remaining vocabulary almost completely eliminated due to the presence of ladies. In relation to the past of the coal industry, we have not only suffered the competition of other energy sources mentioned before, but in addition have in the last 25 to 30 years been required to meet the demands of a vastly changing market. To explain this statement, I am sure many of you can remember 30 to 40 years back when most homes were heated by coal furnaces or stoves and shudder to recall the shoveling of coal into the fire and the carrying out of ashes with the attendent manual labor dust. Now this space heating portion of our sales has almost become non-existant due to an almost universal switch from coal to natural gas, oil, and electric heating. Actual figures show a decrease from 119 million to less than 28 million tons per year in less than a twenty year span. Also, most of you can remember the coal burning steam locomotives and the tremendous volume of coal they consumed and then the very rapid change to the diesel-electric locomotives, incorporating improved large diesel engines driving D C generators and electric drive motors, which resulted in cheaper motive power. This change over was so complete that the annual tonnage of coal dropped from 125 million to less than 2 million tons in 15 years. 'Actually, now it requires some considerable interrogation and traveling to find a locomotive still operating on steam.

Jan 1, 1968

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health(NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

Jan 1, 2003

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

By Robert L. Frantz

The various facets of university-company cooperative activities and the opportunities for collaborative research for the mineral industries are presented in this paper. The advantages and disadvantages of various alternative research funding arrangements for the researcher, the university, and the sponsoring corporation are discussed. Examples of university-industry cooperative research programs are briefly outlined. The concept of a cooperative mining research program is presented. The improvement of performance through techno- logical developments and human skills may well be the greatest competitive edge available to the U.S. mining industry. In this regard, the need for new endeavors between industry and universities can hardly be overemphasized.

Jan 1, 1984

By S. J. Parkin, P. Shead

Extraction of coal at Harworth Colliery is undertaken in the Deep Soft seam at roughly 1000m depth where the strata temperature is 42 "C. Production employs the longwall retreating method using high powered mechanised methods to extract coal at a rate of approximately 40,000 tonnes per week from a single face. This paper describes the climatic conditions encountered on a typical district , 6's district, where the initial ventilation set-up was as a typical U-type district which was antitropally ventilated. Under this initial set-up climatic conditions in the intake typically exceeded 30 "C effective whilst in the face area and in the return airway effective temperatures in excess of 32 "C and 33 "C were common . The paper then proceeds to describe the methods employed to attempt to improve the climatic conditions on the district, especially with regard to the coal face and return airways and describes in detail the effects of reversing the district airflow direction, employing homotropal ventilation, on the climatic conditions. The results of this reversal have been dramatic and have resulted in a substantial improvement in the climatic conditions experienced , however problems have been encountered with the control of methane gas since the changeover. The final part of the paper describes the results of computer simulations to analyse the effect of various ventilation designs on the predicted climate for future production districts in order to de- fine a district layout which will produce acceptable climatic conditions in the working zone without the need to use refrigeration techniques and which will improve methane gas control .

Jan 1, 1997

By J. H. LaVerne Palmer, W. (Bill) C. Cox, Lorant B. Geller

An erector transporter (ET) has been designed and built to lift, carry and erect heavy machinery components, in particular the components of a 7.6 m diameter tunnel boring machine (TBM), within the access tunnels of a submarine coal mine in Eastern Canada. The ET is capable of manoeuvring within a 7.6 m tunnel while precisely positioning components as large as 6 m in diameter and weighing up to 27 tonnes each. The unit can negotiate 20% grades while carrying loads of 30 tonnes. The major design features, verification tests and performance trial results are presented. The versatility of the ET is such that many other applications are possible.

Jan 1, 1985

In 1991, most industrialized countries, except for Germany, were in a recession or a period of reduced growth. The US economy, already in recession, suffered from mounting banking system losses and the uncertainty brought about by the Persian Gulf War. However, US and worldwide minerals exploration did not collapse as it did during the mid-1980s. Even though gold and base metal prices declined, prices were still above cash costs for most operations. This allowed the continuation of established exploration programs but sharply limited new initiatives. Exploration 1990-1991 Planned worldwide 1991 exploration expenditures declined by about 8% from 1990 levels, according to a survey of 153 companies by the Metals Economic Group (MEG). Canada was the leading exploration target with 23% of the total, followed by Australia and the US (19% each), South Africa (13%), Latin America (11%) and the South Pacific (7%). The remaining 8% was split evenly between Europe and the rest of Africa. In Latin America, Mexico and Chile are the most attractive countries for exploration. Recognizing the risks involved, the industry has been cautious about ventures in the former Soviet Union. Survey results also showed that while the majors expected to maintain exploration spending, smaller firms were cutting back or actively seeking farm-outs from the majors (personal communication, M. Wegener, MEG).

Jan 1, 1992

By S. K. Mishra

The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Although coal has been mined in Australia for almost two centuries, there are indications that the first coal was processed in 1877 in the New-castle area, nearly a half-century after the first coal processing in Europe. Processing on any significant scale began only in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The well-known dramatic growth of mining and processing of Australian coal since the mid-sixties has primarily been due to the expansion of the export market in Japan and other Asian and European countries. Black coal occurs in most of the major sedimentary basins in Australia. The better known deposits of commercial importance are in Sydney, Bowen, Oakland and Gailiee Basins (Figure 1). Apart from Collie Basin in Western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory and Tasmania Basin, Tasmania, are basically unexploited. Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia.

Jan 1, 1985

By R. H. W. Chadwick

We in Kennecott are well aware that Alaskans are interested in the progress of our project at Ruby Creek. We would very much like to be able to present you with a final report at this time and tell you about a new mine. I'm afraid, however, that it will be several years at best before such a report can be made. This, then, is an interim report to describe briefly some of our findings to date, and to acquaint you with some of the problems, both geologic and economic, which must 5e resolved favorably before we can talk about a mine. There are several things about this project which make it unusual and interesting to those of us who have been connected with it. Firstly, there is the fundamental importance to Alaska, in the present stage of its economic history, of any undertaking which offers promise of turning a natural resource into a competitive export product. I am sure all of us would get a lot more satisfaction out of having a part in bringing in a new mine in Alaska than we would out of adding another one to the long list in, say, Arizona.

Jan 1, 1960

By Rudolf E. Greuer

Introduction The Institution of Mining and Metallurgy and the Institution of Mining Engineers organized the Third International Mine Ventilation Congress held in Harrogate, England. Sixty-one papers were presented and about 300 participants registered. About 30% of the participants came from Great Britain, 20% from South Africa, and about 5% each came from Australia, Canada, China, France, US, and West Germany. The remainder of the participants came from 18 other countries. Eleven of the papers presented dealt with methane, three with diesel exhausts, four with dust, four with radioactivity, 18 with heat, and 15 dealt with main and auxiliary ventilation. Six of the papers dealt with mine fires, which is a boundary region between main ventilation and gas concerns. Ventilation Congress proceedings are available. See ME, December 1984, page 1687, New Books page. With CH4 and radioactivity topics, the Australians dominated since they are becoming large coal and uranium producers. With diesel exhausts, the most important problem in highly mechanized mines, the North Americans were prominent. The South Africans, working in 90% SiO2 in their gold deposits, were preeminent in presentations on dust. They also led in topics related to heat, joined by the West Germans whose mines are getting deeper. In main and auxiliary ventilation, Great Britain and West Germany provided the majority of contributions. Methane The large number of methods for the precalculation of CH4 liberation in longwall mining all contain three elements: gas content of the coal, gas emitting zone (or influence zone of face), and degree of gas emission. Determination of the gas content, commonly accomplished by taking coal samples, does not pose much difficulty. But this is not the case with the other two factors. Most existing approaches rely on rock mechanics observations. Some only rely on intuition or speculation. The West German coal mines conducted a large research project between 1977 and 1982, in which gas pressures around longwall faces were measured. Gas pressures and gas contents can be related. Therefore, influence zone and degree of gas emission can be determined simultaneously. The precalculation of CH4 liberation in room-and-pillar mining is simpler. Since foot and hanging walls remain essentially intact, gas pressure distribution and gas flow can be calculated using hydraulics equations. A key to these calculations is permeability. A group of Australian researchers reported that the permeabilities of rock under three dimensional stress differs from rock under destressed conditions. This fact was known, but no systematic observations existed. These were provided. Methane drainage has been practiced for more than 40 years. It is used with great success in longwall operations. Some of the West Germans think that methane drainage from the footwall is neglected. Under certain geological conditions, they claim this is as important as drainage from the hanging wall. A research project was presented in support of this claim. Considerable efforts have existed for more than 10 years to use methane drainage in room-and-pillar mining. A paper described the accomplishments of Consolidation Coal Co. Since coal and rock are not fractured as much as in longwall mining, gas transport takes place by the slow diffusion from micropores into the cleats. Then, it is transported by laminar flow along the cleats until a drainage borehole or the mine workings are reached. Boreholes about 300 m (1000 ft) long can reduce the gas content of a band of coal 100-m (330-ft) wide by 50% in one year. A paper from India described methane drainage from gob areas. A French paper reported that especially high methane concentrations can be drained from gob areas if the face ventilation is descensional. Methane buoyancy and ventilating pressures compensate each other, and little air dilution by leakage takes place. Another French paper described a newly developed gas and air velocity monitoring system making use of a microcomputer. Four papers on methane dealt with gas outbursts. Two Australian contributions described the problems encountered with CH,-CO2 mixtures and the attempts to solve them with drainage boreholes having 10 to 20-kPa (1.5 to 3-psi) suction pressures. A Hungarian paper described problems and attempts to reduce the risks of gas outbursts in Hungary. Prediction of gas outbursts in coal seams was the focus of an English paper. Observations show that they are frequent when coal, through its geological past, has become soft and brittle with a resulting increased desorption rate. An instrument for gravimetric de-

Jan 1, 1985

By J. L. Arola

Since start-up of fluxed pellet production in August: 1987, the Minorca Mine has made a number of process changes to improve pellet quality and productivity. Quality improvements include: 1. Installation of a contraction t:ester. 2. Installation of on-line calcium and silica analyzers. 3. Process autocation changes. Productivity improvements include: 1. A second fluxstone storage bin and feeder. 2. A new vacuum pump and disc filter. 3. A filter aid addition system. 4. Enclosing the filter cake reclaim feeder. 5. A new grate bar cleaner.

Jan 1, 1989