Search Documents

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992

By R. M. Imhof, M. J. G. Battersby, J. V. Brown

There is a plethora of former industrial sites where coal mining operations have left large slurry impoundments. These contain raw washed fines, which have previously been too expensive to process to requisite grades for commercial use. New technology has been developed for fine material processing, namely the Imhoflot pneumatic flotation G-Cell. This froth flotation technique is a highly efficient means of concentrating coal and is particularly appropriate to the nature of materials encountered in tailings ponds. The high volumetric throughput resulting from the vastly reduced residence time in the cell allows for drastically reduced equipment sizes when compared to conventional flotation cells. This means the process, when combined with innovative pre treatment and filtration equipment can be developed as a mobile plant concept. This is seen as a minimum requirement when re-treating and rehabilitating fine coal ponds.

Jan 1, 2003

By Peter Zhang, Daniel Su, Bo Kim, Berk Tulu

This paper summarizes significant findings from the ongoing NIOSH Gas Well Stability research over the past decade; in particular, the important ground control engineering considerations. Longwall-induced surface and subsurface deformations may induce gas well casing deformations and stresses, depending on a few parameters such as overburden depth, overburden geology, topographic relief, strata dip, gas well setback distance, and a gas well casing cementing alternative. Overburden depth to the mining seam is one of the most influential factors; shallow overburden depth induces large horizontal displacement and resulting casing deformation and stress, while deep overburden depth induces large longwall-induced vertical pressure. Overburden geology is another important factor affecting the longwall- induced casing deformations and stresses; the large contrast of bending stiffness at the soft-to-hard rock interfaces tends to induce large casing deformations and stresses. Large surface topographic relief and the presence of soft-to-hard rock interfaces below the stream valley bottoms may shift longwall-induced subsurface gas well casing deformations closer to the surface, thus having less impact on underground. mining operations. Strata dip magnifies longwall-induced deformations by 20% per degree of strata dip for down dip longwall excavations. The gas well setback distance is also a critical geometric parameter; the effect of longwall-induced deformation decreases exponentially as the setback distance increases. Longwall-induced casing deformation and stress will be mitigated or totally uncoupled for uncemented production casing.

Jun 25, 2024

By L. G. Closs

Gold continued to be the primary focus of minerals exploration worldwide during 1995. Other targets, though, included primary diamonds and base metals, especially copper deposits amenable to solvent-extraction/electrowinning (SX/EW) processing. The discovery of nickel, copper and cobalt at Voisey Bay in Labrador, Canada was an unusual surprise. Meanwhile, exploration geochemistry continues to evolve to meet new challenges. The major event in this category during 1995 was the17th International Geochemical Exploration Symposium (IGES) held in Townsville, Queensland, Australia in May. The meeting was sponsored by the Association of Exploration Geochemists, which celebrated its 25thanniversary of service to the mineral industry, and the Economic Geology Research Unit of James Cook University, Townsville.

Jan 1, 1996

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By K. A. McDonald

This paper will describe the experiences of Hibernia Holdings, Inc. in constructing a mineral processing facility in Mexico. It will attempt to set forth a guideline on what companies attempting to operate in Mexico can expect and what actions they can take. Ownership laws, import/export laws, labor laws, security, transportation and operating experiences will be discussed.

Jan 1, 1994

By A. F. MacDonald

The rugged foothills of the Allegheny Mountains in Washington County, Southwestern Pennsylvania, lend their terrain very well to the use of aerial tram systems to carry refuse from Bethlehem Mines' two preparation plants to disposal areas some distance from the plant site. Bethlehem Nines Corporation has three deep mines in this area, all of which are mining the Pittsburgh Coal Seam, The raw coal is prepared for metallurgical use in a preparation plant at each mine, Trio of these preparation plants, Mine No, 51, Ellsworth and Mine No. 58 Marianna, use aerial tram systems to dispose of reject material.

Jan 1, 1966

By Andrew I. Hustrulid

The Internet and World Wide Web create multiple opportunities to advance and change an industry. Scandura Conveyor Belting, a mid-sized manufacturing company supplying the mining industry, has embraced several of these opportunities that add value to the sale and service of the manufactured product. This paper presents a technical overview of available technology and how it is being applied to advance the conveyor belt industry. These technologies are used to provide historic catalog information, interactive troubleshooting, product installation and service instructions, detailed product information, technical calculations for the proper conveyor belt selection, and on-line site surveys and maintenance logs.

Jan 1, 2002

By D. J. Barratt

What is meant by "Minimizing Risk"? This paper explores some of the factors encountered in plant design which can affect the success of a mineral processing plant in terms of its planned output, quality of product and recovery. Any deficiency in either one of these objectives means lost revenue at the start of a project and reduced present value for the mine life. Time is money. Related factors such as project conception, feasibility studies, capital cost and operating cost estimation and mining studies have been covered in a recent paper (1) from which material for this paper has been drawn. What follows is a discussion of the principal factors which can influence the success of a project with particular emphasis placed on processing concepts.

Jan 1, 1983

By M. Kung, D. Schwegler-Berry, V. Castranova, D. Lewis, H. Abrons

Pulmonary responses to coal mine dust exposure were investigated by analysis of bronchoalveolar lavage specimens from non-smoking coal miners (n-12, mean age-43 ± 2 years, mean underground exposure-17 ± 2 years) and from non-smoking normal volunteers (n-18, mean age-43 ± 2 years). Spirometric and diffusion capacity indices were monitored as part of a physical exam. Lavage was performed in a subsegment of the right middle lobe by instillation of 200 ml of warmed saline solution in 50 ml aliquots and recovery by gentle suction. Specimens were centrifuged at 500g for 5 minutes at 2°C. Total and differential cell counts were recorded. Secretion of oxidants measured by chemiluminescence, surface morphology (spreading and ruffling), and lymphocyte parameters were determined. Lavage fluid was analyzed for the presence and quantity of acute phase reactants and immunoglobulins. Pulmonary function measurements as well as recovered lavage volume, total lavagable cells, and differential cell counts were similar in both miners and controls. Both resting and phorbol myristate acetate-stimulated chemiluminescence were also similar in miners and controls. In contrast, particle-stimulated chemiluminescence was significantly decreased in the alveolar macrophages from the miners (48% of control values). Morphometric analysis of scanning electron micrographs indicate that phagocyte surface spreading was similar in miners and controls. However, surface ruffling was 127% greater in the miners compared to controls. Lymphocyte subpopulations were similar in miners and controls. Protein analysis of the lavage fluid revealed lower total protein content in the lavage fluid of miners. However, the concentration of albumin, IgG, and IgA were similar in miners and controls. We conclude that most indices were normal in underground miners working under the current dust standard of 2 mg/m3. The decrease in particlestimulated chemiluminescence and the increase in surface ruffling in miners may suggest the beginnings of particle overload and activation of the macrophages. In addition, a decrease in total protein was noted in lavage fluid from miners.

Jan 1, 1991

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some 2,000 years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today, more mineral commodities are mined in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions. Old industries are generally considered stodgy with mature and stagnant technologies. Costs tend not to decline as in newer industries, and may even increase with real wages. Costs are particularly expected to rise in the case of mining as the best mineral deposits are depleted. Thus, mining is often thought of as a sunset industry, destined to decline over time as the resource base is depleted. These perceptions have several important implications. They argue against economic policies that rely too heavily on mining and mineral processing to foster growth and development. The best and the brightest young people, along with society's other valuable resources, should be encouraged to enter newer industries. There the technological opportunities and the prospects for growth are more promising. These perceptions also suggest that the ability to compete in the mining industry depends largely on the quality of a company's or country's mineral deposits. Mining will take place first in countries with the lowest-cost deposits. Once these are exhausted, mining will shift to countries with the next best deposits. From time to time, new discoveries may also produce a shift in the location of mining, [ ] and may even for a time keep the costs and prices of mineral products from rising. Over the longer term, however, rising costs and prices are inevitable, as the world is forced to exploit poorer mineral deposits.

Jan 1, 1997

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992

By William G. Holroyd

In January 1992, the Office of the US Trade Representative announced that the People's Republic of China had agreed to protect US intellectual property, including computer software, sound recordings, agrichemicals and pharmaceuticals. Under the agreement, China will make significant improvements in its patent, copyright and trade-secret laws. Ambassador Carla A. Hills, the US trade representative, said "this agreement should create significant opportunities for US firms interested in marketing high valued-added products to China." Principal beneficiaries will include the agrichemical and computer industries, as well as pharmaceutical, entertainment. The agreement will safeguard these industries' intellectual property, stimulating new exports to China and helping to generate additional growth in the US. Refractory grade bauxite was included in the mineral category of the $1.5 billion of Chinese products on which the US government threatened to impose an immediate 100% trade tariff. Refractory bauxite is available from Guyana and Brazil at higher cost and in different grades. However, refractory brick manufacturers would have had little choice but to pass on the costs to their consumers. Although the United States and China are separated by political ideology and internal governing structures, this agreement recognizes the importance of a $19 billion trading relationship. Consequently, the renewal of China's most favored-nation trading status in the US congress in -June 1992 was all but assured. Many US companies doing business in China and Hong Kong have been quietly increasing their investments since 1989. These companies can now concentrate on developing sales to the domestic Chinese market. This market is expected to surpass 1.2 billion people in 1995 and approach 1.3 billion by the end of the century.

Jan 1, 1993

This paper reviews the historical literature and the author's experience with regard to the effect that the selection of grinding ball size or sizes has on ball mill grinding efficiency. The conclusions presented provide guidelines for single and multi-size charging prac- tices in commercial milling operations.

Jan 1, 1998