Search Documents

By A. Tarigan

The integration of the ESZ orebody and DOZ orebody resulted in a much larger footprint than the original DOZ Mine shape. The significant change in footprint geometry presented new cave front management challenges, specifically: longer undercut drifts. Using a constant blasting rate, more time is required to complete caving in each drift which ultimately influences the number of active faces at any point in time. The number of manageable active drifts is controlled by the planned square-meters of undercut blasting, lead/lag restrictions and other specific conditions such as the need to blast pre-charged explosives. In early 2008, an evaluation of the existing plan showed that significantly more active undercut drifts and longer cave fronts would occur in the next five years. Difficulties associated with the long cave fronts led to a decision to redesign the caving sequence. Several different boundary options based on operational, geotechnical and ore grade parameters were investigated. This paper describes the issues faced with long cave fronts, the constraints and requirements to effectively manage the caving sequence and the options considered to mitigate this situation.

Jan 1, 2010

By Houston Kempton, Tim Dyhr, Andy Davis, Mark Bloom, Connie Travers, Dave Atkins, Jeff Deen

INTRODUCTION Historical mining activities in the Robinson Mining District, in the Egan Range of east-central Nevada (White Pine County), resulted in five open pits (Veteran, Tripp, Liberty, Ruth, and Kimbley Pits), several large mine-waste dumps, and numerous underground workings developed for copper, zinc, gold, lead-silver, and manganese (Figure 1). Groundwater percolating downward through the copper sulfide ores produced a blanket-like supergene zone enriched in copper, which has been one of the primary objectives of mining since the early part of this century. To obtain permits for future operation, an EIS was conducted that evaluated future pit- lake chemistry, groundwater quantity and quality issues, transport of water and solutes subjacent to a proposed tailings impoundment, and the potential for waste dump acidification. AREA HYDROGEOLOGY The mine area is on a ridgeline draining to the Steptoe Valley to the east and to the White River Valley to the West. Precipitation in the Robinson Mining District ranges from a low of 15 cm (6 in.) per year in the valley to more than 50 cm (20 in.) per year in the surrounding mountains. Evapotranspiration exceeds precipitation, leading to a net loss of water from the basin as either surface flow or underflow to the north at Currie, Nevada (Eakin et al. 1967). The White River Valley, which lies to the south and west of the mine area, includes approximately 4,200 km2 (1,620 mi2) of the upper part of the Colorado River Basin. This valley is 112 km (70 mi) long, 32-48 km (20-30 mi) wide, and like Steptoe Valley, evaporation and transpiration exceed precipitation (Maxey and Eakin 1949). The local groundwater flow system in the Robinson Mining District and the proposed mine area is dominated by two main components: (1) a groundwater mound or high between the Ruth Pit and Murry Springs, and (2) a shallow groundwater flow divide that follows the ridge crest south of Ruth, which contains the Veteran and Tripp pits. Besides the alluvium, the main hydrostratigraphic units controlling groundwater flow are limestones, shales, and sandstones, along with the intrusive quartz monzonite stocks. Based on the piezometric surface measured in October 1993, three distinct groundwater regions were identified. In the Giroux Wash area, an apparent fault runs between WCC-G1 and WCC-

Jan 1, 1995

By Felicia F. Peng

A laboratory fixed bed reactor was used in a study of generating clean thermal energy from coal fine refuse-limestone agglomerates. The major operation variables, including Ca/S mole ratio, agglomerate size, air flow rate and temperature, which affect the rate of sulfur fixation and combustible material utilization, have been examined. The test results show that 70 percent or more of sulfur fixation and 100% of combustible material utilization can be achieved depending upon sorbent, agglomeration, and combustion conditions. The coal fine refuse limestone pellet combustion process (CLC process) requires a simple flowsheet to convert coal fine refuse as a clean solid fuel, while meeting the strict air quality standards for SO2 emissions into the atmosphere. The CLC process is an attractive method to clean up coal slurry impoundments to protect our environment.

Jan 1, 1984

By T. Altman

Using theory of network planning together with graph theory, an algorithm is presented that creates canonical diagrams for mine ventilation networks (M VN). The data generated by the algorithm is used in the construction and plotting phases of a program that automatically plots the canonical diagrams, which can then be used for further studies of a given MVN.

Jan 1, 1988

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite (Bayer Process) is known as red mud. Approximately one ton of red mud is produced for every two tons of bauxite mined. The red mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that more than 90% (by weight) alumina can be recovered from red mud by soda ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of more than 94%, resulting in attempts, for magnetic separation. These separations are desirable because there are no waste products generated. Consequently, there is an opportunity for complete utilization of the waste material. Conversely, the preseparated material could be charged through the tuyeres in an iron blast furnace, or it could be smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag would be high enough to justify its recovery by an established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red mud as an alternative to direct-reduced iron (DRI) is also discussed. A critical assessment of the recovery sequence chosen for the products is described based on economics. Key words: Red mud, Waste product utilization, Alumina recovery, Titanium oxide, Iron

Jan 1, 2003

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By Rainer Kahrger, Guenter Ewald

The topic of this paper is to demonstrate the development of mobile crushing installations from throughput capacities of 200 tons per hour, to mobile and semi-mobile large- scale crushing installations with throughput capacities of 3,500 up to 10,000 tons per hour. Basis are approximately 140 mobile and semi-mobile crushing installations which have been built since 1956 or were on order in 1987. [FIGURE 1. Total Number of Mobile or Semi-mobile Crushing Plants] Sixteen of these approximate 140 mobile and semi-mobile crushing installations have a throughput higher than 3,500 metric tons per hour. Mobile crushers were developed more than 25 years ago in Europe for the quarry industry, which had special requirements - fairly low capacity, mostly softer and less abrasive material (limestone) and full mobility. So the majority of the units up to about 1980 were fully mobile, having a fairly small capacity and utilizing mainly hammermills, double roll and impact crushers. It was only when the mining industry and large quarries picked up the concept in the early 1980's that a drastic increase in capacity took place. Even though the first mobile crusher in a true mining application went into service in 1971, it took another 10 years before it proceeded in a larger scale. This trend was obviously supported by the drastic fuel price and energy cost increase in the mid 70's. Since the cost of conveying material is substantially cheaper than trucking it, the increase in energy cost, combined with increasing haulage distances provided a strong incentive. Figure 1 shows clearly the throughput distribution of all crushing installations and it also shows the sharp increase in the throughput capacities within the last few years.

Jan 1, 1989

By David Sugden

Intense, tropical weathering of Cretaceous-Tertiary sediments has developed similar laterites in distant areas of the Amazon Basin. In two areas, Trombetas and Paragomina s, bauxites of commercial potential arc found. The bauxite comes mostly from the lower horizon of the three component laterite. The laterite is overlain by a clay cover, possibly an integral part of the weathered profile. The laterites are found on almost flat plateaus with individual areas of up to 80km2. There is a close relationship between the morphology and the ldterites. The process of lateritization is allegedly Pliocence but probably continues today.

Jan 1, 1984

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By Kefton H. Teague

History of the feldspar industry in the United States has been summarized by DuBois (I)*. The earliest production of feldspar in the United States is reported to have been from Mitchell County, North Carolina, about 1744, with the product shipped to England, In about 1825 several pegmatites were worked to a limited extent in Connecticut, with the production shipped to England. The first feldspar grinding facility was constructed about 1850 in Connecticut, with chaser mills used. Feldspar has been produced continuously in the United States since about 1870. Feldspar is produced from the following states: North Carolina, California, Georgia, Connecticut, South Carolina, South Dakota, Kansas, Oklahoma, Virginia, Arizona, and Wyoming. Total United States production for 1969 will amount to approximately 900,000 tons. The most current published figures for world production is 1966, at which time 2,165,000 tons was produced. It is estimated that world production of feldspar for 1969 will amount to 2,410,000 tons. Historically, feldspar has been produced by hand sorting and hand cobbing of coarse block feldspar obtained from the intermediate and wall zones of zoned pegmatites. In the United States the reserve of known block feldspar, recoverable by hand sorting is nearing depletion. More emphasis is now placed on feldspar sources contained in finer grained rocks, especially coarse granites or fine-grained pegmatite and beach, dune, and river sands from which the feldspar is obtained by beneficiation.

Jan 1, 1970

By Aurel Goodwin, Diann Kraft, V. S. Znamensky

This chapter deals with the Mine Safety and Health Administrations's (MSHA] concern and obligations with regard to asbestiform minerals. Asbestiform minerals are defined as the magical group of hydrated, silicate minerals that possess a fiberlike structure capable of being woven into cloth. Their unique combination of properties, such as resistance to heat and chemical attack, high tensile strength, and flexibility was recognized centuries before Christ. Pausanias, the early Greek geographer, speaks of golden lamps, made about 430 BC, with in- combustible wicks of Carpathian flax. The Ro- mans used asbestos as cremation clothes to con- serve the ashes of deceased persons of rank. Charlemagne had an asbestos table cloth that he used to pass through fire to clean (Lanza, 19381. Early recognition of the health hazards associated with exposure to asbestos was documented in the first century by Pliny the Elder, a Roman naturalist, and Strabo, a Greek geographer. Both wrote of slaves with sickness of the lungs, whose occupation was that of weaving asbestos into cloth. This concern for the health of asbestos workers disappeared over the ages. Today, with the use of modern technology, asbestos products have been greatly exploited. The asbestos output has increased over a hundredfold in the past 70 years. World production has jumped from 454 t/y (500 stpy) in 1900 to 4.5 Mt/y (5 million stpy) in 1978. An increase in health problems for asbestos workers accompanied this increased usage. However, it was not until the modern era that the association of asbestos with chronic respiratory disease was rediscovered. Reports were published at the turn of the century documenting the effects of asbestos exposure on textile workers. One such report in 1907 by H.M. Montague Murray described the post mortem findings on a 34-year- old carding machine operator. Murray de- scribed the lungs as showing extensive diffuse pulmonary fibrosis spicules of asbestos. Subsequently, more reports of pulmonary fibrosis following inhalation of asbestos were published, including an epidemiological study of asbestos miners in 1930 (Merewether and Price, 1930), at Thetford, Que., Canada. This study took place at the mine 52 years after large-scale mining of asbestos had begun. But, the cancer- producing potential of asbestos was not established until 1949 when a report by Merewether in England described an excess of cancer of the lung and pleura [the lining of the lungs) among individuals dying from asbestosis (Merewether, 1949). In the past decade much attention has been focused on asbestosis, mesothelioma, and bronchogenic carcinoma, as the three major biological effects associated with asbestos ex- posure. Parenchymal and pleural asbestosis is a fibrosis in the substance of the lung with thickening and often calcification of the membranes lining the thoracic cavity. Mesothelioma is a malignant tumor of the membranes lining the thoracic or abdominal cavities, and bronchogenic carcinoma is a cancer of the lung tissue itself. These diseases occur in various degrees and combinations. The severity and occurrence of these biological effects are directly influenced by conditions such as dose response relationships, intensity of exposure, duration of exposure, lapse of time since initial exposure, and cigarette smoking. Numerous studies indicate that the relationship between these conditions and the incidence of disease is proportional. Congress has recently concluded (Congressional Record, 1979) that, "exposure to asbestos fibers has been identified as significantly in- creasing the incidence of cancer and other severe or fatal diseases such as abestosis." Congress conveys its concerns for the safety and health of the nation's miners through the Federal Mine Safety and Health Act of 1977 in which it gave MSHA the authority to set safe

Jan 1, 1986

By F. L. Wilke

Bong Mining Co. Ltd. in Liberia, West Africa, operates an iron ore open pit some 60 miles northeast of Monrovia. The production is at present about 40,000 t/d (metric tons/day) from which about 18,500 t/d concentrate with 65.5% Fe is produced. The ore waste ratio is about 1: 1.5 to 1:2. The technical layout and the equipment are very similar to those in many modern open-pit operations as described by Jacobs and Thomson (1967). As described by Lersch in detail (1966), the deposit is a very irregular one. The quality of the ore changes within very short distances with regard to both physical conditions (hardness) and chemical properties. Very soft and very hard ore as well as high-grade and low-grade ore are found adjacent to each other. In addition, there are enclosures of sterile rocks. For the purpose of identification and production scheduling, 12 different types of ore are distinguished.

Jan 1, 1979

By Levent Ozdemir, Russell Miller, Fun-Den Wang

The full utilization of tunnel boring machines for excavation in medium hard and hard rock has been limited by insufficient knowledge of rock behavior under the action of mechanical cutters. An understanding of factors affecting the rock removal process will permit: (1) the more efficient design of tunneling machines, (2) the prediction of boring performance from geologic data and cores taken from the proposed tunnel alignment, and (3) an improved excavation rate, thus a lower tunneling cost.. The Colorado School of Mines, under the sponsorship of the National Science Foundation, is studying the effects of a number of parameters in regard to tunnel boring using both full and small scale laboratory tests, analyzing field boring performance and comparing the laboratory and field data. Results indicate: (1) the field boring performance can be reproduced in the laboratory, (2) the optimum spacing of cutters or optimum spacing to penetration ratios may be found in laboratory testing, (3) it is promising to use small core samples and laboratory testing to predict field machine performance and (4) effect of joints on boring rate is significant and should be included in predicting tunnel boreability.

Jan 1, 1974

By J. D. McAuliffe

The Homer-Wauseca Mine is operated by the Hanna Mining Company, three miles north of Iron River, Michigan on the Menominee Iron Range. The mine produces 5,300 tons of direct shipping iron ore daily. The present main producing level is at a depth of 1,500 feet below the collar. The ore body continues to a depth of 2,700 feet below the collar, to which depth the modern circular concrete shaft has been completed. A view of the property is shown in Figure #1. This paper is a report on the development of large underground boreholes used initially to conduct stope filling material into inaccessible, mined-out stopes. Later holes were drilled for ventilation raises, for mine drainage, for passageway for power cable, also for the primary breaking point for long hole stoping. Some, which were drilled as ventilation raises, were later stripped to a suitable size for a manway or ladder road. The holes varied in size from 6" to 30" with the present popular, economical working size being 16 1/4", used as a stope fill passage in mined out areas and for ventilation in deeper development. Foremost has been the desire to develop equipment suitable for drilling raises large enough for manways.

Jan 1, 1963

By R. J. Piniazkiewicz

Talc orebodies are mined in Asia, Australia, Europe, North America, and South America. Operators in North America must be efficient quality suppliers to thrive in a talc market in which many overseas suppliers have advantages such as lower hourly wages, shorter distances to ports, and less government regulation and intervention. Continuous improvement through teamwork and innovation is needed in the following areas to thrive amidst worldwide competition: 1) Maximization of the in-place value of ore. 2) Research and development to yield new processes and products. 3) Safe productivity. 4) Involvement in legislative processes. 5) Wellness programs to lower health care costs.

Jan 1, 1993

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By Chunlin He, Xinsheng Li, Feng Yang, Lu Han, Yuezhou Wei, Feng Gao

The solvent extraction of vanadium (V) from Na2CO3–NaHCO3 solution was attempted using Aliquat-336 (methyltrioctylammonium chloride) extractant dissolved in sulfonated kerosene as diluent with 2-octanol as phase modifier. The influence factors, such as Na2CO3 concentration, NaHCO3 concentration, temperature, extractant concentration and impurity P, on vanadiumextraction were investigated. The results revealed that the single stage extraction efficiency of vanadium reached above 89%from 20 g/L Na2CO3 – 20 g/L NaHCO3 solution under the following conditions: extractant concentration of 15%, room temperature of 20–30 °C, 2-octanol of 6%, phase ratio (O/A) of 1:1, and oscillation time of 1 min. The addition of NaHCO3 into Na2CO3 solution could lower the pH value of the Na2CO3 solution, improve extraction efficiency of vanadium, and not introduce other impurities. The phosphate anion did not interact with the vanadate anion in the Na2CO3–NaHCO3 solution. The P in the Na2CO3–NaHCO3 solution had little influence on vanadium extraction.

Jul 30, 2020

By M. B. Mirza, W. A. Sadik, B. T. Stanley

This paper presents the ventilation design for an underground testing facility in a salt medium. The under-ground workings consist of two 3.6 m-diam (12 ft-diam) watertight shafts and about 1830 m (6000 ft) of drifting. These facilities are designed to provide access for an in situ testing of a salt horizon in which a variety of hazardous and nonhazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1987

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978