Search Documents

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By H. Lind

Mining in Estonian oil shale deposit mainly takes place in the Ordovician, Keila-Kukruse aquifer. The aquifer is affected by mining and is fully dried out around the working mine areas (Perens and Savitski, 2008). The groundwater level is decreased down to 30 m, to the mine floor elevation using about 30 pumping stations (Lind, 2005). The pumping rate is very high - depending on the season, ranging from 10 up to 40 m3 per ton of produced oil shale (Reinsalu et al., 2006). The Estonian oil Shale Company mined 15.5 million tons of oil shale in 2007 (Source: Estonian Oil Shale Company). In order to predict the effects, and avoid the social and environmental impacts, there is a need to continuously monitor the situation and run software simulations aiming at decreasing the pumping rate. This becomes even more important since the environmental taxes on usage of groundwater resources increase every year. Therefore, it is necessary to monitor groundwater level and quality, and develop a groundwater model for the overview of the situation during mine operations and also for a number of years after mine closure.

Jan 1, 2008

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By Hans-Christian Kurzweil, Klaus Mussger

CERN, the European Laboratory for Particle Physics, are upgrading their existing particle accelerator for the next generation of experiments and have three major packages of underground construction work in progress. Each package involves the construction of shafts, cavern, tunnels and surface buildings. This paper gives an overview of CERN, the LHC Project and a more detailed discussion of design process, design review and construction works of Experimental Point 5. The LHC works at Point 5 include two large shafts, two major parallel caverns with a total span of 50 m, which are separated by a 7 m wide and 28 m high concrete pillar, and a system of secondary tunnels and caverns. The overburden ground consists of around 50 m of water bearing moraine (silty, clayey gravels and sands) overlying 20 mof molasse, which consists of horizontally bedded marls and sandstones. The shaft shave been constructed with ground freezing, primary concrete lining, membrane and secondary slip formed concrete lining. The concrete pillar was then excavated and concreted in advance of excavation of the two caverns. Cavern construction includes primary support of shotcrete lining and rock bolts, followed by waterproof membrane and primary support of shotcrete lining and rock bolts, followed by water proof membrane and insitu concrete secondary lining.

Jan 1, 2003

By J. O. Guthrie

Newmont has delineated a 600,000+ ounce gold reserve in the Cargo Muchacho Mountains. This is a desert range underlain by Proterozoic(?) Tumco Formation (gneiss) intruded by Jurassic granitic plutons, and cut by low angle shears of the late Cretaceous Chocolate Mountain Thrust event. Gold, associated with pyrite, quartz veinlets, and propylitic alteration, is emplaced along low angle shears. The mineralizing system, enriched in tungsten, copper, zinc and arsenic, was active during Eocene time. Gold reserves are found in eleven areas as moderate to high tenor deposits that may be mined by open pit and underground techniques. Eastmaque Gold Mines Ltd. is developing the deposit.

Jan 1, 1987

By N. Prenn

"INTRODUCTION The 2014 SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (the SME Guide) has been adopted by the Society for Mining, Metallurgy, and Exploration, Inc. (SME). The SME Guide is recommended as a minimum standard and a basis for developing industry best practices in the classification of Mineral Resources and Mineral Reserves for public and private purposes. The Guide is therefore strongly recommended to be used by members of this organization. The SME Guide was updated in 2014 to include CRIRSCO (Committee for Mineral Reserve International Standards) core definitions, and it is envisioned that the U. S. Securities and Exchange Commission (SEC) will adopt the SME Guide in 2016. However, as of the end of 2015, the SEC Industry Guide 7 remains the standard for the U.S. reporting of Mineral Reserves. This paper will cover the classification of Mineral Resources and Reserves, a discussion of Modifying Factors, and the classification definitions and guidelines. The definitions and guidelines contained in this report are from the SME Guide. FRAMEWORK FOR MINERAL RESOURCE AND MINERAL RESERVE CLASSIFICATION Figure 1 illustrates the classification of Mineral Resources and Mineral Reserves using the Guide. Mineral Resources are divided into three classifications of Inferred, Indicated, or Measured while Mineral Reserves include Probable and Proven classifications. These classifications reflect improved knowledge and confidence of the deposit from the top of the figure to the bottom. In other terms, the deposit risk also decreases from top to bottom.The relationships in Figure 1 reflect different levels of geoscientific knowledge and different degrees of technical and economic evaluation. Mineral Resources can be estimated on the basis of geoscientific information with input from other disciplines to establish reasonable prospects for eventual economic extraction. It was not too many years ago that the classification of a Mineral Resource was based on the evaluation of a limited set of factors that included spatial drill hole and grade distribution (kriging variance, as example), distance to the closest hole, and number of samples used to estimate a block grade. These are still important considerations, but classification following the Guide must also take into account sample integrity, sample QAQC, database integrity and completeness, geological understanding, and geological and grade or quality continuity. In addition, a general consideration of the Modifying Factors, to establish reasonable prospects for eventual economic extraction, adds complexity to the classification."

Jan 1, 2016

By Thomas J. Neil, O&apos

Mine land reclamation is a comparatively new science-Although some mining companies point with pride to reclamation efforts of 20 to 30 years ago these were the exception rather than the rule. In the last ten years the skyrocket of environmental awareness has been awesome to behold. Future shock gripped mine operators everywhere as they struggled to cope with rapidly changing and escalating demands. The initial result was that two divergent points of view became dominant. Environmentalists said, "Put it back the way it was," and the miners responded, "Let's grow some weeds and hide it." These views are not surprising as they represent rather obvious alternative responses, albeit at opposite ends of the decision spectrum. The former case has prevailed more often than the latter, as most state and federal legislation -- both proposed and passed -- has required drastic alteration of the post-mining landscape so that evidence of prior mining is largely obliterated. An exception to this has been in porphyry copper country where the infrequent abandonment of mines has given emphasis to the second philosophy -establishing vegetative cover on mine waste materials. Now, it should come as no revelation to most mining people that both of these approaches to mine reclamation suffer from serious drawbacks when applied to open pit copper mines. First, whereas waste dumps and tailings dams can be vegetated with some aesthetic benefit, the massive presence of copper mining operations remains very prominent. It is difficult to conceal an open pit copper mine. Second, returning open pit copper mines lands to their original topography and productivity is simply not a reasonable alternative.

Jan 1, 1976

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By Wenbing Guo, Mingjie Guo, Hebing Zhang

As resources are depleted in coal mines, isolated support pillars are often mined. Cemented paste backfill has been used to provide support during the mining of these pillars due to its safe and green mining characteristics. However, traditional cemented paste backfill mining has some shortcomings, such as poor adaptability to geological structure, leakage of paste during filling, imperfect roof-contact in partially backfilled areas, and insufficient roof strata support before the backfill reaches its design strength. This paper presents the results of a case study where L-shaped interval cemented paste backfill technology has been safely used to mine an isolated coal panel beneath existing surface structures. This backfilling method has the advantages of preventing paste leakage, improving the backfilled ratio, reducing surface subsidence, and strongly adapting to geological structure. During this field application, the setting pressure of the backfill shield reached 20 MPa, the compressive strength of the backfilling body reached 2.0 MPa, and the backfilled ratio reached 93.7%. Observational ground monitoring showed that roof-to-floor convergence in adjacent roadways ranged from 132 to 167 mm. No obvious fractures or separations in the overlying strata were observed by a borescope. The maximum surface subsidence was 342 mm, the subsidence factor was 0.136, and the damage to surface buildings was within Grade I (slight damage). This case study clearly demonstrates that the L-shaped interval cemented paste backfill method can be safely used to mine the isolated coal panel beneath surface buildings.

Jul 1, 2023

By D. A. Swanson, G. Danziger, G. Savci, C. Barnes

Hydrologic assessments of existing and proposed waste rock stockpiles are typically required for application of operating and closure permits at mine sites. A hydrologic assessment should include an evaluation of climatic data and prediction of the net infiltration rate through the waste rock stockpile surface. In addition, hydrologic factors such as the time required to deplete available moisture storage in the stockpiles and the time required for potential seepage to migrate to the underlying aquifer should also be predicted.

Jan 1, 2000

By Bing Wang, Jingli Fan, Qinying Song, Fengyu Li, Xian Zhang

"With the background of water shortages and serious water pollution, issues of water involved in energy exploration and utilization have become critical problems affecting urban water usage. In order to identify the relationships of the energy-water nexus, this paper characterizes the energy-water nexus literature using a bibliometric method and based on the Chinese National Knowledge Infrastructure database platform. The results reveal that 1) Scientific outcomes in this field have increased sharply since 2003, with a slightly higher growth rate than that of general disciplines. 2) China Water Resources, Yangtze River and Express Water Resources & Hydropower Information are the dominant journals, and the main research fields include industrial economics, environmental science, and management, among other disciplines. 3) Hohai University, the Chinese Hydraulic Engineering Society, the Institute of Geographic Sciences and Natural Resources Research, and the Changjiang Water Resources Commission are the main research institutions in this field. However, the proportion of publications of these institutions is not high, which suggests that there is no institution dominating this field. 4) According to the keyword analysis, the hot spots in this field include ecological environment, sustainable development, environmental protection, climate change, etc. Energy-mining related keywords have increased over time, implying that the energy-water nexus from the perspective of the energy exploitation industry can become a key issue. At the same time, the frequency of keywords related to sustainable development has been maintained at a high level, and the studies concerned with the impacts of climate change were introduced into this field relatively late. The conclusion of this study provides a foundation for a comprehensive understanding of the current situation as well as for further research in the energy-water nexus field.Introduction As an important strategic resource for national economic and social sustainable development, water has been increasingly focused on by the Chinese Government. Over the next decade, the total water demand of China will continue to grow steadily, which lead to a significant trend of increasing water consumption in the future (Zhang 2013). To reasonably exploit, utilize, conserve and protect water resources, the Water Law of the People's Republic of China was enacted by the members of the 9th National People's Congress Standing Committee in 1988 and after multiple revisions, the latest of which, in September 1, 2016, has involved water infrastructures in the national economic and social development plans of the government at all levels and regulated the rationale for water engineering construction. Thus, in the context of serious water shortages and water pollution, China’s government has taken several measures to make rational use of water resources."

Jan 1, 2017

By P. K. Muduli

The number and the type of trucks and shovels are two important factors in determining the optimal design parameters of an open-pit mining system. Characteristics of trucks' arrival and service-time distributions determine the performance measures of a truck-shovel system when it is modeled as a closed queuing network. In all of the previous analytical queuing studies of truck-shovel systems, trucks are assumed to be identical with respect to their arrival and service-time distributions. This assumption, although desirable for reducing computational difficulties, causes either underestimation or overestimation of the performance measures depending on the number and type of equipment used in the model. The relative error in performance measures could be significant when the number of different types of trucks and shovels is large. In this paper an analytical method is proposed to model the truck-shovel system as a multiple-chain closed queuing network. This approach would provide the capability of estimating system performance measures for planning purposes when the truck fleet is not necessarily composed of identical trucks. An example of truck-shovel systems is discussed to show how the incorporation of different types of trucks does affect performance measures.

Jan 1, 1996

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By R. D. Beard

Puerto Rico lies within the remnants of a deformed Cretaceous island arc system in the northeastern Caribbean. The Island can be divided into three broad geologic provinces: the Central Volcanic-Plutonic Province (Lower Cretaceous to middle Eocene), and the Northern and Southern Limestone Provinces (early Oligocene to middle Miocene). Known precious metal deposits are generally small and occur in veins and shear zones within Lower and Upper Cretaceous volcanic and plutonic rocks. Some Tertiary igneous rocks are also mineralized. Selected indications of disseminated lithology-controlled mineralization could represent larger deposits. Associated metals in some deposits include copper, zinc, and lead. At present, tax policies, population density, political outlook, and lack of proven significant precious metal deposits discourage the establishment of a metal mining industry.

Jan 1, 1993