Search Documents

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By M. P. Corriveau

This is the case history of how two nearby plants in Southwest Virginia solved their water clarification problems. While the solutions should not be considered applicable industry-wide, the methods used in arriving at the answers deserve consideration. When Clinchfield's Moss No. 2 Preparation Plant, the first ever built in Tiller Seam coal, was started in the fall of 1956, the clays in the raw coal soon posed a flocculation problem, Laboratory sedimentation tests were initiated; and as a result, lime was adopted as the flocculant for the clays, With lime, a pH of 11.2 was required. As the plant tonnage increased, it became evident that the amount of coal fines produced in the mining and preparation was greater than had been estimated and that the 90-foot thickener was inadequate in providing sufficient settling time to effect a clarified overflow for reuse. Testing showed that Separan 26105 (NP10)1/, when used with lime, was the most satisfactory coal flocculant available,

Jan 1, 1960

By Peter C. Finlayson

Rapidly rising gas and oil prices and the falling quality of coal is forcing energy users in many parts of the world to consider the application of low grade fuel, particularly coal, for steam raising and power generation. However, the use of such low grade coal is normally resisted by the consumer because of operational problems associated with high ash content, sulfur emission and, in some instances, slagging problems caused by low melting temperature constituents in the ash. Recently developed technology involving 'fluidized bed combustion' offers a potential solution to these operational problems. Much of the early work was conducted in Britain, where rig tests were commenced during the early 1960's. This has led on to the successful conversion and operation of a fluidized bed fired industrial boiler at the Renfrew works of Babcock & Wilcox Ltd. Orders for the first commercial boilers incorporating this technology have recently been announced. Significant development work on fluidized combustion is now being undertaken in various parts of the world, in particular North America, Germany and Japan, and the first large scale units are under construction or being commissioned. This paper concentrates on the development of the technology in Britain, outlines the reasons for applying fluidized bed combustion and de-scribes its application at atmospheric pressure for steam raising and at elevated pressure for power generation . Coal Processing Consultants is a Partnership between the National Coal Board and Babcock & Wilcox Ltd. of Britain and has been established in order to provide technical advice and economic evaluations on all aspects of coal processing and utilization. In view of the involvement of its Parents in the development and exploitation of fluidized bed combustion technology, Coal Processing Consultants has been retained by clients in various parts of the world to provide expert advice on the application of fluidized combustion for particular coals and project situations.

Jan 1, 1978

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By George H. Klein, B. Kent Merritt, Anthony Crisci

During the past decade, over 114-km (71-mi) of 0.25-m (10-in) to 3.7-m (144-in) finished diameter tunnels have been driven below Metropolitan Houston as part of a major program of water and wastewater improvements. This large effort has seen the introduction of midwestern technology with over 18-km (11-mi) of man-entry pipe jacking and European and Japanese technology with over 21-km (13-mi) of microtunneling. Owing to the high water table; a stratigraphy consisting of stiff fissured clays containing numerous layers, channels, and lenses of water-charged sands and silts; and active faults, many challenges existed for designers and contractors alike.

Jan 1, 1991

By Richard H. Sillitoe

Gold is an important byproduct and, locally, coproduct of porphyry copper deposits, and possesses potential for discovery as the major metal in porphyry deposits in either island arcs or Cordilleran belts. Tungsten and tin occur as major components of several potentially bulk-minable porphyry deposits, as well as being byproducts from the Climax porphyry molybdenum deposit. Whereas porphyry tin systems are localized in Cordilleran back-arc settings, their tungsten counterparts appear to span a range of geotectonic settings, from Cordilleran principal arcs through back-arcs to rifts. Although silver is a common byproduct of porphyry copper deposits, it tends to be preferentially concentrated with lead and zinc on the fringes of all types of porphyry deposits and/or as late-stage superpositions; the latter situation could be of some interest in the higher parts of porphyry systems. As byproducts, rhenium, uranium, platinoids and magnetite are exploited occasionally, and rutile and the rare metals, such as tantalum and niobium, have merited consideration.

Jan 1, 1982

By Ammar Henchiri

INTRODUCTION A current need of the phosphate industry is the development of process technology for treatment of high carbonate content ore. About 75 to 80 percent of the world phosphate reserves (1) are associated with carbonate gangue, which is not amenable to treatment by the existing techniques. Numerous laboratory and pilot plant studies have been devoted to carbonate-phosphate separation. Different techniques were involved (washing, sieving, attrition, flotation, calcination, and leaching). For technical and economical considerations, flotation appears to be an efficient process for this problem. Separation of carbonates (calcite and dolomite) from igneous phosphate is applied in industrial plants in Brazil, Finland, and South Africa. But, for sedimentary phosphate, no industrial realization exists at this time, with the possible exception of some plants in China. The main problems with sedimentary phosphates are: • high substitution by CO3-2 and F- for P04 -3 in the apatite lattice. • larger surface area of the phosphate particles because their surface is porous and irregular. • tendency of sedimentary minerals to produce more slimes in conditioning than the crystalline minerals, hence, larger dosages of collectors are required for sedimentary minerals. Investigations reported in the literature indicate that most processes developed for sedimentary carbonate-phosphate separation involved inverse flotation of carbonates using fatty acids as collectors (2), (3) associated with phosphoric acid (4), monosodium phosphate (5), F- (6), or SiF6 -2 (7) as phosphate depressants. Later investigations, conducted by A. Henchiri and G. Baudet (8), (9), (10), (11), (12), (13) in the BRGM technology department, of phosphoric esters revealed that these reagents are selective collectors for carbonate-phosphate separation. The above investigators developed a process which used phosphoric esters to collect carbonate minerals and sulfuric acid or sodium fluorosilicate as depressants for phosphate. Extensive comparative tests for different processes on the same phosphate sample show that the process developed at BRGM is one of the most promising methods proposed for sedimentary phosphate-carbonate separation. It should be pointed out, however, that phosphoric esters make abundant froths. The handling of these excessive froths will be a problem in an industrial-scale plant. This paper outlines test work performed in order to optimize and to improve the efficiency of the flotation process on a sedimentary phosphate ore selected from the Sra Ouertane orebody. The Sra Ouertane flotation process, illustrated on Figure 1, first removes carbonate minerals by inverse flotation and then recovers phosphate as a froth product, leaving quartz as a cell product.

Jan 1, 1993

By G. W. Luxbacher

With the advent of acid rain legislation included within the Clean Air Act Amendments of 1990, a great deal of uncertainty with regard to price, source and production quantities has been cast into the coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward, South American coals move into the northern markets, states propose legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries, while some utilities question the long term availability of eastern compliance coal. Any major coal producer must make decisions now to assure their continuing presence in the market place; several companies have adopted a strategy to acquire eastern compliance reserves while others have invested in technology to compete as a low cost producer. This paper discusses some of these options in light of the uncertainties of the market place, from an eastern coal producer?s viewpoint.

Jan 1, 1992

By P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous Chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972

By Philip D. Lindahl

The US Bureau of Mines (USBM) began research to improve the safety and efficiency of transporting coal from underground coal mines using a balanced air-lift hydrohoist (ALH). ALH includes a U-tube pipeline that can be installed through an existing shaft or two surface-drilled holes connecting the mine level to the surface. Bench- and pilot-scale models were tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a riser pipe by injecting compressed air microbubbles. A prototype injector was developed that continuously compacted -50-mm (2-in.), run-of-mine coal in a screw feeder and injected a thick coal slurry into ALH. Initial production rates of 40 t/h (44 stph) through a 200-mm-(8-in.-) diam riser pipeline were achieved with a50-m- (165-ft-) high pilot-scale model. The potential productivity was expected to increase to 100 t/h (110 stph) through modification of the coal injector.

Jan 1, 1995

By C. J. Veal, C. I. House, S. R. Bellamy

INTRODUCTION Coal gold agglomeration (CGA) is a new concept in gold processing. It involves the recovery of oleophilic (oil-loving) gold grains by causing them to adhere selectively to the surfaces of coal oil agglomerates. Under optimum conditions very high recoveries of gold. can be achieved. The agglomerates are recycled to build up gold loading to typically 1000 - 5000 g/tonne. Bullion can be produced by burning the loaded agglomerates with subsequent recovery of gold from the highly loaded ash either by dissolution/electrowinning or smelting. A wide-ranging programme of laboratory testwork has been performed to investigate the response of different ore types to the process. This has shown CGA to be most applicable to ores in which the gold is liberated or easily liberatable, relatively coarse (ca 500 µm) and fine (<5 µm) gold grains being recoverable with equal ease. The best opportunities for CGA seem to be: • placers containing fine gold not recoverable by gravity concentration • low grade gravity concentrates to avoid multiple magnetic/gravity separation stages and amalgamation • free milling ores where the gold can be liberated at a reasonable ore particle size eg >d80 50 µm • tailings past or present from gravity concentration plants. CGA testwork ranging in scale from laboratory to pilot plant on tailings produced by gravity concentration in the 19th century Australian gold rush has already been reported (Bonney, C F, 1988; House, C I, Townsend, I C and Veal, C J, 1988). An economic appraisal for a Canadian free milling gold ore has also been published (Buckley, S A, House, C I and Townsend, I G, 1989). This paper describes results of a detailed laboratory programme to assess CGA as a means of recovering gold from a beach sand deposit in New Zealand. The area from which the samples were taken consists of quarternary interglacial marine, lagoonal, fluvial and eolian deposits. The heavy minerals present are predominantly ilmenite and garnet and small concentrations of gold. In certain locations the sands and gravels are consolidated by a limonitic cement. In the 19th Century some parts of the deposit were mined and the ore processed using stamp milling and gravity concentration. Gold recoveries were low, probably below 50%, due primarily to the fine size of the gold grains, the flaky nature of the gold and also imperfect liberation by the stamp mills. Our laboratory testwork was divided into three parts: i) Preliminary studies on an initial sample to assess the feasibility of treating the ore by CGA ii) Extended studies on further samples from various locations in the deposit to confirm predictions from (i) iii) Conventional gold recovery techniques. EXPERIMENTAL PROCEDURES All CGA tests were performed by agitating a slurry of ore in water in a 0.6 dm3 pyrex beaker fitted with four vertical baffles. When required, potassium amyl xanthate collector was added and the slurry conditioned for 5 min. Coal (ex BP Coal Australia&apos;s Tahmoor Colliery) previously ground to a d80 50 µm was added followed by a commercial grade of gas oil (density 840 kg/m3). The agglomeration time was 30 min. The agglomerates were separated from the tailings by screening, both were then dried and analysed for gold by fire assay. This test procedure provides a reasonably accurate estimate of gold recoveries that might be expected from our 1 tph pilot plant. Ore samples were ground either dry in an agate ring disc mill or wet in a steel batch tumbling

Jan 1, 1989

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator&apos;s training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is overcompacted. Research has shown that excessive compaction in replaced growing media is detrimental to the establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky developed test cells on reclaimed areas at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. Each test cell was planted with various species of trees, and for the first two years of tree growth, data were collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data were statistically correlated to determine how ripping affects the relationship between soil compaction and tree survival rate.

Jan 1, 2003

By Brianna Eiter, Max Barham, Tim Bauerle

While not well established, there is evidence that the mining industry is encumbered by several work-related fatigue risk factors. Compared to other industries, mine workers are more likely to report inadequate sleep and work longer hours per day. Given these observations, there is a critical need to identify effective ways to intervene, manage, and mitigate mine worker fatigue and sleepiness when present. One barrier to this is confusion around the similarities and differences between fatigue and sleepiness, which can result in these terms being treated as interchangeable regardless of context and make it difficult to assess and mitigate safety risk.

May 1, 2024

By Gene E. McClelland

4.1 INTRODUCTION Metallurgical testing is required on any ore, waste or tailing material before amenability to heap leaching treatment can be accurately determined. The amount of testing necessary to determine and optimize heap leach amenability and conditions for any feed material is determined by the ore type, grade, size of deposit, and the overall financial commitment a particular company is willing to make. It is very easy to either "under-test" or "over-test" a particular deposit or feed material. A good heap leach testing program will provide the necessary design information without "bogging" down in too much detail. The three basic stages of ore testing include: • Preliminary--bottle roll tests and small column percolation leach tests; • Detailed--larger column tests, different feed sizes, and feed size optimization; and • Pilot-Scale--Column or field heap. The following subchapters describe the stages of heap leach testing necessary to put a viable property into production. 4.2 PRELIMINARY METALLURGICAL TESTING The two types of preliminary tests that can be undertaken include bottle roll or cyanide agitation tests and small column leach tests. Each of these is described below, along with information about what the test results provide in terms of furthering knowledge of ore qualities. 4.2.1 Bottle Roll Tests The first step in a heap leach testing program is preliminary bottle roll tests at a relatively coarse feed size to determine the ore&apos;s leachability. Bottle roll tests are usually conducted on reverse circulation drill cuttings samples (= 1/4 inch (6 mm) in size). Bottle roll tests provide initial information about precious metal recovery, recovery rate, and reagent requirements. The recovery results are to be considered maximums because attrition grinding creates fines and liberates recoverable values that would not be liberated from the material during a static leach. Bottle roll tests can be conducted on up to 25 lb (11 kg) ore charges of up to two inches (50 mm) in size. However, the coarser the feed the more attrition grinding occurs during rolling.

Jan 1, 1988

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By P. Mousset-Jones, F. Calizaya

Currently, a 4.3 km long drift is being developed on the 3440 level in the Lower Kalamazoo project at the San Manuel Mine, Magma Copper Company, AZ. The drift, located at 1050 m below surface, is being constructed using a 4.6 m diameter tunnel boring machine (TBM). The drift is ventilated by a forcing type auxiliary ventilation system. At the face, to mitigate the impact on the work environment of the TBM, the system is equipped with dust extraction and refrigeration systems. Recently, to evaluate the ventilation conditions in the drift, a continuous monitoring system has been installed. The system can be used to measure the air velocity, barometric pressure, relative humidity and air and rock temperatures. This study describes the capabilities and limitations of this system, and presents a summary of the results.

Jan 1, 1995

By E. D. Attanasi, J. H. DeYoung

Several factors contributed to continued declines in mineral-exploration activity in the US in 1985. Low metal prices and, what appears to be worldwide chronic excess capacity in copper, molybdenum, lead, and uranium, have resulted in mineral-exploration expenditures remaining anemic. Economic recovery could result in a healthier mining industry and more cash flow to fund exploration. This is because general economic activity and US mining industry activity have historically been closely linked. However, as the worldwide economic recovery has expanded, the mining sector has continued its downward slide. New cuts in industry exploration budgets in 1985 shocked those who thought the exploration situation could not become worse. Some personnel and equipment had been redirected from base metals exploration to precious metals in the past few years. Last year, continued reductions in exploration sent many professionals out of the mining industry. Recent staff reductions or consolidations of operations were made by Noranda, Chevron, Molycorp, and other exploration companies. The latest data from the Society of Economic Geologists (SEG) summary of exploration statistics show that professional staff at year end in major US exploration companies (domestic and foreign operations) fell from 2355 in 1981 to 1868 in 1983 and 1277 in 1984. By the end of 1985, two economic trends were established that could improve the future profitability of mining and hence exploration. First, the price of crude oil began a decline. If sharply reduced energy prices increase worldwide economic expansion, the substantial excess capacity in some of the base metals industries could disappear, and prices could improve. Furthermore, if energy price declines reduce mining and processing costs significantly, metals may recapture some lost markets. The decline in oil revenues has already encouraged some oil-producing countries, such as Venezuela, to look toward development of mineral resources to earn foreign exchange for debt repayment. Second, the decline of the dollar by 21% during 1985 could also help US producers meet foreign competition. During 1985, industry restructuring continued as many oil companies sold off mining subsidiaries and minerals properties. Gold, silver in new discoveries Precious metals continued to dominate the announcement of new discoveries and exploration projects in 1985. A review of domestic exploration and development activities reported in several industry journals shows that 60% to 80% of these projects were directed primarily at precious metals, particularly gold. Base metals exploration activities frequently involved polymetallic deposits with gold or silver values. Because much of this exploration was done on identified targets (on-property exploration), the decrease in wildcat or grassroots (off-property) exploration may be more substantial than indicated by reductions in total exploration activity. Significant gold discoveries in 1985 included several in Nevada, among them the Genesis property of Newmont (near the Carlin mine), Goldfields&apos; discovery of the Chimney deposit in Humboldt Co., and Freeport&apos;s discovery of two mineralized sites near Jerritt Canyon. Gold exploration continued to be focused in the western US and Alaska, but gold production starts at the Haile mine in South Carolina, and the Ropes mine in Michigan as well as Amselco&apos;s feasibility studies on deposits near Ridgeway, SC, are evidence that gold exploration is not limited to the West. The dominance of gold projects in exploration is not limited to the US, as demonstrated by gold dis¬coveries and exploration projects in Australia, Brazil, Canada, the Caribbean region, China, Guinea, Ivory Coast, South Africa, the South Pacific islands, and Thailand. From the standpoint of US metal miners, it is perplexing that worldwide exploration and development is also taking place in copper, zinc, tungsten, and other metals with depressed prices. During 1985, the US Geological Survey&apos;s efforts to map the sea floor of the Exclusive Economic Zone shifted from the Pacific Coast to the deep water areas of the Gulf of Mexico and to areas off the coast of Puerto Rico and the Virgin Islands. An atlas containing sea-floor maps of the west coast area was published as US Geological Survey Miscellaneous Investigations Series Map 1-1792. Results of the 1985 surveys are expected to be published by January 1987. Exploration trends - Statistical evidence Data from the SEG showed continued decline in the US mining industry&apos;s exploration expenditures through 1984. The share of US companies&apos; domestic exploration expenditures directed toward base and precious metals has increased from 51% to 84% from 1980 to 1983 and to 86% in 1984. US mining companies spent about $0.67 of each exploration dollar in 1984 in the US. However, this represents an increase from earlier years. The 1983 data also show that firms spending more than $5 million on exploration accounted for 77% of exploration expenditures. Since 1981, the Bureau of Land Management (BLM) has been assembling data on claims and an-

Jan 5, 1986

By T. Naarttijärvi

The Fabian ore body near Malmberget, Sweden, has an ore reserve of 5 Mt of predominately low grade iron ore, containing 40-55% Fe. Mining began in 1971 with a new method called slot block caving. About 2 Mt were mined, but poor fragmentation resulted in too much secondary blasting. This decreased mucking efficiency to such an extent that the method was abandoned after only 40% of the ore volume had been mined. At this stage a large stope (180 x 30 x 100 m) had been excavated. Although the exposed area was quite large, no caving action occurred in the hanging wall or in the ceiling. LKAB decided in 1977 to introduce sublevel stoping using 105-mm-diam holes. This was the first time large diameter holes were used underground in Sweden. The method had been evaluated in collaboration with the University of Luleå (LuH), the Swedish Detonic Research Foundation (SveDeFo), and the Swedish Mining Research Foundation.

Jan 3, 1982