Search Documents

By Terry S. Maley

Federally owned mineral deposits generally fall into one of three categories: (1) minerals locatable under the General Mining Law of 1872; (2) minerals leasable under the Mineral Leasing kt of 1920; and (3) minerals salable under the Materials Act of 1947. Unlike valuable deposits of gold, silver, copper, iron, lead, etc., which may be locatable, industrial minerals are acquired through a variety of methods depending on use, composition, and date of acquisition. Table 1 may be used to establish the method of acquisition for most industrial minerals.

Jan 1, 1987

By Joseph J. Wojcik

INTRODUCTION A great deal more is involved in a sampling effort directed at a placer deposit than physically capturing a quantity of representative material and extracting the desired component. The distribution and dimensions of the sample sites must be chosen after consideration has been given to the type of deposit and the concentrating mechanism. Interpretation of the sampling results is likewise an extremely important part of the sampling program. SAMPLE SPACING The interpretation begins with the selection and design of the sampling program. A decision regarding genesis of the deposits and their geometry must be made in order to select a suitable technique and sampling pattern. Deposits differing genetically will have differing distributions and degrees of concentration.

Jan 1, 1992

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By Jacek Kolacz, Knut Lyng Sandvik

Fine grinding in an air swept and a grate discharge ball mill working in closed circuit with a forced vortex air classifier has been investigated in continuous laboratory scale. Minerals with different physical properties were ground down to 40, 20, and 10 micron top size. The shape of the product particle size distribution curve was investigated and specific surface (BET) was measured. During production of material with top size of 40 microns in an air swept mill, the capacity was up to 25% higher when compared to a grate discharge mill. This difference dropped to 180A during production of 10 micron top size material. A corresponding decrease in power consumption was observed. An important finding is that by regulation of the air flow rate through the mill, it is possible to achieve products with different specific surfaces and particle size distribution curve steepness. During production of the 10 pm material, the specific surface could be varied in the range 3 to 4.5 m2/g. Such powders could hardly be produced in a grate discharge mill because fine particles coated the grinding media and the lining. On the other hand the internal classification in the air swept mill kept the size distribution of the mill content relatively free of fines. This prevented a similar slowing-down of the air swept grinding process.

Jan 1, 1995

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By Irwan Halim, Bhoshaga Mitrran Ravi Chandran, Kevin Huynh

Tunnel segmental lining design constitutes a significant iterative process where modeling and numerical analysis are factors in deciding the number of segments, their dimensions, gasket placements, as well as the locations of dowels and bolts. Consequently, these modifications lead to revisions in the final drawing details. However, the current tunnel engineering practices lack systematic solutions that effectively bridge the gap between the iterative design process and efficient visualization of completed drawings due to the time- consuming nature of redrawing. This paper presents a pioneering application of AI-driven solutions including using Autodesk's API, for the Northside Interceptor Tunnel (NSIT) Project. It showcases the automation of drawing design and the real-time visualization of modifications, thereby streamlining the drawing process.

Jun 23, 2024

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and medium-term activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter and ventilation constraints in order to create more realistic schedules, and enhance miners’ health and safety.

Jan 1, 2024

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By Fred Leighton

INTRODUCTION Dynamic (seismic or microseismic) methods of determining the stability of structures in rock are based on detecting and analyzing the characteristics of seismic energy that has originated from or traveled through the rock mass. This seismic energy can be in the form of naturally occurring rock noise energy resulting from structural adjustments within the rock or can be introduced into the structure by physical means, such as by blasting or impact. In either case, the seismic energy radiating through the rock mass can be detected using standard equipment and can be analyzed by established techniques to reveal a wide variety of information concerning the condition and stability of the rock mass through which the energy has traveled. In the following sections, the basic instrumentation required for seismic and microseismic studies is described, and some of the presently used applications of these methods are discussed to exemplify the state of the art. INSTRUMENTATION Seismic disturbances in a rock structure generate two types of seismic wave radiation, body waves and sometimes surface waves, which radiate outward in all direc¬tions from the source of the disturbance. Underground mining applications are generally concerned only with discerning the characteristics of the resulting body waves, i.e., the compressional (p-wave) and the shear (s-wave) energy. As these two forms of energy travel through the rock structure, the particles of the rock mass are caused to vibrate, and the vibration character¬istics resulting from each of the two types of wave are distinct. Some important differences are: 1) Compressional and shear waves travel at different velocities through the rock structure. 2) The frequency at which each wave causes particles to vibrate is different, and may range from about 50 to 100 000 Hz. 3) The amplitude or energy level of each wave is different, with the shear energy usually being the greatest. These differences form the basis for equipment se¬lection for individual studies and for modern data analysis techniques. The following sections describe the basic equipment necessary to detect and record seismic wave energy data and show several examples of analysis procedures and how these procedures have been used. In principle, seismic equipment is very simple. It consists of a geophone (or geophones) to detect the seismic energy vibration and convert that vibration to an electric signal, an amplification system to increase the level of that signal, and a means of monitoring and/or recording the signals detected. Fig. 1 is a block diagram of a typical system. The following sections offer a very brief discussion of system components and their individual functions. A more complete discussion is given by Blake, Leighton, and Duvall (1974). Geophones The function of the geophone is to detect the vibrations caused by the passing of the seismic wave energy and to convert that vibration into an electrical signal that displays both the amplitude and frequency characteristics of the vibration. Particle motion or vibration can be quantified and measured by measuring displacement, velocity, or acceleration of the particles. Thus, there are three types of geophones: displacement gages, velocity gages, and accelerometers. The choice of gage depends on the characteristic frequencies of the seismic energy to be monitored and the sensitivities of each type of geophone. In general, displacement gages are used for low-frequency monitoring (periods to 1.0 Hz), velocity gages for medium-frequency monitoring (1.0 to 250 Hz), and accelerometers for high-frequency monitoring (250 to 10 000+ Hz). Experience has shown that in underground studies, the choice of which gage to use lies between velocity gages and accelerometers. An easy, accurate method for selection of gage type is discussed by Blake, Leighton, and Duvall (1974). Once the type of geophone has been selected for use, it must be properly installed, and in the installation procedure the most important step is insuring that the gage is firmly attached to a competent portion of the rock structure. Poorly mounted geophones may entirely fail to recognize low-level seismic signals and will distort the information from signals they do see. Amplifiers Seismic events associated with mine structures occur over a very broad range of energy which results in a broad range of geophone output levels. In general, geophone output levels occur in the microvolt to low milli-volt range, and it is necessary to amplify these signals in order to drive recording or monitoring equipment. Because either an accelerometer or a velocity gage might be used as the geophone, the amplification system must

Jan 1, 1982

By Anthony Iannacchione, Tim Miller, Nicole Evanek

The Subtropolis Mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, OH. In February 2018, mine management began implementing a new mine layout to better control the negative effects of excessive levels of horizontal stress. Almost immediately, the conditions in the headings improved. Conversely, and as expected, stress-related damage was concentrated within crosscuts. Over the last 18 months, the mine operator has diligently experimented with different techniques/methods to lessen the impact of the instabilities in the outby crosscuts. The range of controls used by the mine operator include angled crosscuts, crosscut offsets, increased distance between crosscuts, arched crosscuts, cable-bolted crosscuts, altered blasting pattern, and windows. A window is used to resist roof deformation by leaving a strong brow of roof rock within the crosscuts.

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989

By Charles Kimbell, L. Nahai, E. Shekarchi

INTRODUCTION AND SUMMARY World mineral trade during 1960 to 1984 has shown substantial changes both in value and tonnage. Although fuel commodities dominated total mineral trade during this period, this paper will focus attention primarily on nonfuel minerals. Brazil and Australia, modest producers of iron ore in 1960, have become dominant producers and exporters, together accounting for about half of major iron ore exports in 1984, far surpassing traditional export suppliers such as Sweden. Australia has also become the largest producer and trader of bauxite and alumina, and worldwide alumina trade has increased at the expense of bauxite trade. Similarly, shipments of ferroalloys have increased more than shipments of ores such as those of chromium and manganese. Canada, retaining its first rank in world export of zinc, has become also the leading source of potash and sulfur in world trade, and South Africa has been the dominant factor in chromite, manganese and their respective ferroalloys. Developing countries' share of world copper trade has increased, with Chile maintaining first rank, but developed industrialized countries have continued to dominate production and trade of lead and zinc. Phosphate, sulfur, and potash have been the principal crude nonmetallic minerals traded worldwide. Looking to the near future, dramatic increases in export of iron ore, phosphate, potash and sulfur are not envisaged. Bauxite exports will continue to decline relative to alumina but at a slower rate than in the recent past. Zinc concentrate will continue to be exported but lead will be traded more as metal than as concentrate. For iron and steel, there will be some production shift from traditional producers to certain developing countries and recently industrializing developing countries such as Brazil, India, the Republic of Korea, and Taiwan. In the following sections dealing with specific commodities, it should be understood that information is presented only on the major forms of each commodity that move in trade, and only for a selected group of countries for each commodity or major form of each commodity. Thus, totals shown or mentioned generally represent only the totals of figures presented here and do not include estimates for minor forms of material or for countries that are not listed. However, the data provided is regarded as sufficiently complete to reflect major patterns and trends, and exclusions are there- fore not seen as affecting conclusions that may be drawn from the material provided. FUEL AND NONFUEL TRADE Values of Fuel and Nonfuel Trade The value of world export trade in major mineral commodities (ores, concentrates and scrap, crude minerals, iron and steel, nonferrous metals, nonmetallic minerals and mineral fuels) in 1983, the latest year for which comprehensive data are available, was reported by the United Nations in May 1985 to have totaled over 514 billion current U.S. dollars (Table 1). This was 79% of the historic record high of nearly $649 billion ,current dollars set in 1980, but almost 18 times the current dollar value reported for 1960. [1/] The value of these 1983 exports in constant 1960 dollars was $164 billion (Table 2), only 66% of the record 1980 high of almost $250 billion, and only about 5.7 times the 1960 dollar level.

Jan 1, 1986

By S. Mathur

The southern Florida phosphate deposits that will be mined in the future contain significant amounts of dolomite. Because high MgO levels are undesirable in phosphoric acid production, several flotation schemes for the removal of the dolomite have been attempted. Alternatively, selective flocculation has been suggested as a potential process. A high MgO rock was simulated with a 30:10:60 mixture of apatite, dolomite and silica, respectively. Single mineral selectivity was observed in the apatite-silica and dolomite- silica systems using Polyacrylic acid (PAA) and Poly(ethylene oxide) (PEO) flocculants, respectively. However, no single mineral selectivity was observed in the apatite-dolomite system using PEO. Heteroflocculation, suspected to be the major reason for the loss of selectivity, was minimized by the addition of a site blocking agent (SBA), consisting of a lower- molecular-weight fraction of PEO. Process parameters such as size reduction schemes, flocculant/SBA dosage and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed-mineral tests was also achieved in the ternary mixed-mineral system, namely, the apatite-dolomite-silica system. In this report, surface chemical characterization of the samples and their flocculation behavior are discussed.

Jan 1, 1995

By J. Pinkley

In June of 2002 Hilti North America received the first MSHA permissible approval for usage of a powder actuated tool device in a gassy mine atmosphere. The purpose of this paper is to discuss the implementation of this commonly utilized tool technology in the construction industry, to the underground gassy mining industry over the course of the last 5 years. Prior to June of 2002, underground gassy mining industry had attached materials such as ventilation curtains, power cables, communication cables, signage, and other materials by either manually driving individual spads or nails into the mine roof or rib or by attachment to existing roof bolt bearing plates. The Hilti DX 460 powder actuated tool is portable, durable, and lightweight (4.5 pounds). The Hilti DX 460 powder actuated tool system is powered by Hilti .27 caliber permissible explosive boosters. The energy force of the Hilti .27 booster?s acts on a captive piston principle in the Hilti DX 460 powder actuated tool, that applies the setting force for the direct fastening to the individual fastener chosen for the application by the end user. Each year Hilti can be called upon by MSHA to provide booster materials for re-testing per our Hilti DX PAD 1/00 approval.

Jan 1, 2008

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine-opening stability. Laboratory test data, borehole measurements and geological mapping assisted in the construction of a coupled finite element model of the rock mass. The model was used to make quantitative estimates of rock stress, strain and displacement changes and to make estimates of the water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. The stability of the crown pillars between stopes was of particular interest. The relatively low effective stress and high rock-mass strength showed that water pressure changes were of no great consequence, which is in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific data.

Jan 1, 2002

By K. Hebbar, R. G. Reddy

The viscosities of various FeO-SiO2 slags were calculated using a previously developed structural-based model. Using hole theory and the atomic pair model, an expression was derived to relate the viscosity to temperature and the fraction of the bridging oxygen in silicate melts. The deduced equation was successfully applied to predict the viscosities of FeO-SiO2 slags in the composition range of 0.1 < XSi02 < 0.423 for several temperatures. The calculated data agree well with the experimental viscosity data.

Jan 1, 2002