Search Documents

By Ronald E. Heuer

The significance of surface settlement over soft ground tunnels is well recognized. Cracked buildings, streets transformed into lakes, broken utility lines, to underpin or not to underpin--all are familiar problems. The basic causes of surface settlement are recognized. Possibly the most common and troublesome cause is "lost ground" during construction. Lost ground refers to removal of a larger volume of ground (Ve) than is eventually occupied by the final tunnel structure (Vt). A number of sources of lost ground in shield tunneling have been identified, as illustrated in Fig. 1. These include 1) face loss, 2) overcutting loss, 3) annular tail void loss, and 4) loss through the lining. The ground generally does not stand unsupported around the completed tunnel lining as illustrated in Fig. 1, but moves in to fill the lost volume, resulting in subsidence of the overlying ground surface as shown. As suggested in Fig. 1, lost ground and surface settlement associated with overcutting and the annular tail void tend to occur systematically along the tunnel length. This "systematic" lost volume is "limited" in the sense that it is restricted to an upper limit determined by the shield and lining geometry. Partially controlled face loss may sometimes contribute to this systematic loss. This lost volume is commonly a few percent of the nominal tunnel volume. The resulting surface settlement over the tunnel is commonly in the range of a few inches or less and develops over a period of hours to days. Although they may have a significant impact on surface facilities, systematic ground loss and settlement frequently have little adverse effect on tunneling progress.

Jan 1, 1976

By Yoginder P. Chugh, M. Silverman

Premining investigations involve the determination of roof, floor, and coal seam characteristics to delineate areas of troublesome ground control prior to development of a mine. Data obtained can be useful in mine design, equipment selection, estimation of face productivity, development of ground control plans and assessing ground control costs, and in conducting feasibility studies and financial analyses. This paper discusses 1) the causative factors associated with ground instability, 2) how useful data can be obtained for these factors during premining investigations, and 3) analysis techniques to delineate probable areas of ground instability.

Jan 1, 1982

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By Wolfgang Sand, Alex Schippers, Tilman Gehrke, Thore Rohwerder, Peter-Georg Jozsa

Metal sulfides are degraded via thiosulfate (pyrite) or via polysulfides and sulfur (sphalerite, galena, chalcopyrite) by leaching bacteria The attack on the crystal lattice is either effected by only iron(III) ions or by iron(III) ions and protons, respectively. Consequently, different endproducts are formed. For a control of ARD-processes, these reactions need to be hown to regulate them. Experiments in percolators up to 65 m3 with inorganic compounds like fluoride, concrete, or SDS resulted in differently lasting inhibition. Microcalorimetric measurements of microbial leach activity allow monitoring of these effects with respect to active bacterial cells, and, in addition, the amount or rate of dissolved metal sulfide allowing prediction of possible endangerment by ARD.

Jan 1, 2000

By A. B. Van Cleave

It was first pointed out in 1934 by Gaudin (1) that the "oily" oxidation product of the alkyl xanthate ion-dialkyl dixanthogen, might be the "active flotation agent" on sulphide minerals and there have been a number of studies supporting this hypothesis (2,3,4). However, all of these studies have relied largely on electrochemical evidence. Galena, being a semiconductor, may be used as an electrode in aqueous solution and it was shown that ethyl xanthate ion does not adsorb with charge transfer in the absence of oxygen unless the potential of the galena surface is above -100 mv versus the hydrogen electrode (H2 E). At this potential the galena surface is slightly hydrophobic but does not become strongly hydrophobic unless the potential is raised to 210 mv (versus H2 E). It is suggested that, at potentials of 210 mv or above, ethyl xanthate ions are oxidised to diethyl dixanthogen and that chemisorption of oxygen raises the galena surface to this potential. On the other hand, examination of xanthated galena surfaces by chemical or physical methods (5,6,7) has failed to detect dixanthogen and it has been shown that dixanthogen may be reduced to lead xanthate at a lead sulphide surface. (5,8)*. It was suggested by Leja and Poling (5) that, as dixanthogen is a neutral molecule it would not be repelled by the negatively charged galena surface so that the adsorption was envisaged as taking place through homogeneous oxidation of the xanthate ion to dixanthogen, adsorption and reduction of the dixanthogen to a chemisorbed lead xanthate species. In paper I of this series (11) it was shown that the thiosulphate ion, which forms on galena surfaces in slurries at the pH normally used for flotation, will reduce dixanthogen. There is, therefore, the impasse that the electrochemical evidence requires that xanthate ion be oxidised to dixanthogen at the galena surface while the chemical evidence shows that the reverse reaction takes place.

Jan 1, 1973

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979

By Stephen Pogorski, Colin R. Phillips, Atika Khan

An optimized counting scheme for a mixture of radon daughters and thoron daughters typical of Ontario mines, developed in a previous study, was experimentally examined under mine conditions. The counting scheme requires a 10 minute sample and 5 1/2 hours counting instead of a 60 minute sample and more than 40 hours counting as required by a previous method. Taking into account the uncertainties associated with concentrations, flowrate and radioactive decay, the precision of the counting scheme was analyzed and found to be on average better than the 40 hour method.

Jan 1, 1981

By Viggo C. Bertelsen, David G. Hammond

LOCATION AND EXTENT OF BART TUNNELS The San Francisco Bay Area Rapid Transit District (BART) during the past six years has become the Owner of 23.5 miles of single-bore tunnels. The tunneling experience gained while working closely with our Engineer and Contractors in the design and construction of these major transit facilities provides a basis for our "Owners" viewpoint. The 23.5 miles of tunnels are divided into two categories. Fifteen and one-half (15-1/2) miles of tunnels were constructed in soft ground underlaying the downtown areas of San Francisco, Oakland and Berkeley. Eight (8) miles of tunnels were built in "hard ground" in the hills separating Oakland and Berkeley from Contra Costa County and in the San Francisco hills on the Mission Line. Location of tunnels within the BART system are shown on Figure 1. The tunnels comprise 15.7% of BART's 75-mile dual track system. Their 176 million dollar costs (excluding rail, electrification or ventilation features) are 12.4% of the system's total estimated cost of $1.4 billion. The tunnels constructed in soft ground were shield and boring machine driven with ground support provided by steel liner rings. The exterior diameter is 17 foot, 6 inches in the majority of tunnels; however, on two tunnels with a 500 foot radius of curvature, the diameter was 18 feet. BART awarded 14 contracts for soft ground tunneling. The work was accomplished under free air or compressed air depending upon the ground water and soil conditions, safety requirements, and considerations for protecting adjoining property from damage either from the de-watering operations or settlements due to excavation. The tunnel bores, except on curves, were normally parallel being spaced at 32 foot centers on the Mission

Jan 1, 1997

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

By Richard D. Doepker, Cathy A. Summers

Part 1: Physical Characteristics The physical and mineralogical characteristics of samples from five sources in the Western United States were determined using size analyses, microscopic studies, and point counts. These results were combined with leachability assays and the chemistry of leachates obtained during slurry tests to predict sample dissolution characteristics during column leaching tests. Part 2: Dissolution Characteristics Two columns of each sample were leached over a period of 3 years with synthetic rain. Residence times were between 2 and 11 weeks. The samples were subjected to daily and seasonal temperature fluctuations and wet-dry and freeze-thaw cycles. During the latter part of this study, a biocide leachant (sodium benzoate) was substituted for synthetic rain to assess the degree of dissolution caused by biological oxidation. It was found that the presence or absence of barite or carbonate minerals can be used to predict the leaching behavior of the column material.

Jan 1, 1995

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By Robert Klug, Nils Engelke

"In order to extract proportionately small quantities of valuable minerals, mining companies move large amounts of earth. A resulting waste product of this process has traditionally been stored in a semi-liquid phase known as tailings, typically stored in a large pond created by an earthen dam at the low end of a drainage basin. It is generally expected that these dams are stable enough to withstand the pressure of the stored material. Unfortunately, history shows us that this is not always the case. The Baia Mare dam in Romania failed in 2000, causing tragic and prolonged environmental damage to several major European rivers. The Bento Rodrigues dam in Brazil failed on Nov. 5, 2015, and that event resulted in the loss of 16 lives.In hard rock mining, many minerals are imbedded within the ore. As part of the mining process, valuable minerals are extracted from the ore; often, the mineral content is only a fraction of the total ore volume processed. To extract the minerals, the ore is typically crushed and pulverized into very fine particles, then wetted to form slurries. The minerals are extracted from the slurries through a series of flotation and/or sedimentation steps with the aid of water-soluble separation chemicals typically known as reagents. Following the mineral extraction, the resulting residual wetted ore cuttings are labeled as tailings. At the end of the extraction process, the tailings are in a thick semi-fluid sludge state, often with trace elements of the extraction reagents.Historically, these tailings are deposited in giant basins or sludge ponds, where they pose a great threat to the environment while binding large volumes of waste process water.Process water recovery and achievingdry tailingsCurrent generation engineering studies, trials and successful field implementation have shown that an alternate process known as dry stacking is practical. The dry stacking process deposits dewatered tailings into containment areas that are smaller in overall footprint and significantly safer by reducing the transfer of reagents into the tailings storage area. In addition to achieving the dry tailing benefits mentioned, it is possible to recover valuable process water while dewatering the tailings sludge utilizing modern separation technology."

Jan 4, 2018

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By W. F. Hahnert, T. L. Ward, K. E. Stoll, P. A. S. Ralston

Fuzzy logic is well suited to the control of non-linear, time-varying, and/or any system for which it is difficult to obtain an exact mathematical model. To design a good fuzzy controller, a thorough understanding of the desired process behavior is required. Many papers have suggested that fuzzy controllers are robust. If they are, it is reasonable to explore whether or not they respond better than conventional controllers to errors in the feedback signal due to imperfect measurement or sensor degradation. It may be the case that simpler or less expensive sensors could be used in some processes. The research presented here relies on an integrated array of computer programs that model and simulate (1) the process to be controlled, (2) common feedback instrumentation, and (3) both fuzzy logic controllers (FLC's) and conventional controllers. Various types of feedback sensor imperfections are imposed upon the system, and the performance of the two controllers is compared. Each controller is tuned to its optimal performance in response to a setpoint change using perfect feedback measurement.

Jan 1, 1993

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

Jan 1, 2006

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By M. Tokoglu

Accurate estimation of resources is one of the major challenges in mineral project evaluation. Contemporary mineral resource estimation practice calls for contribution from several disciplines and execution of several interdependent tasks. 3D estimation domain modelling is obviously one of the most essential components of such a substantial process which forms the basis of this research. The study constitutes a comparative analysis of four major domain modelling techniques; (i) explicit modelling, (ii) implicit modelling, (iii) indicator kriging, and (iv) conditional simulation. It involves comparison of outcomes for alternative scenarios to assess the implications of the modelling decision on resource estimates of a polymetallic massive sulfide deposit located in western Turkey. Thus, identical grade estimation method and parameters are considered to identify the discrepancies arising only from the choice of the domain modelling approach and underlying assumptions. Economic implications are demonstrated in the form of range of outcomes for the extends of the ultimate pit, ore tonnages (min:37.0 Mt, max: 46.7Mt), waste tonnages (min:201.2 Mt, max: 251.2 Mt), stripping ratios (min:5.18, max: 5.71), and total pit values (min: $1.05B, max: $1.45B). Examination of solid models as well as cross-sections revealed that major discrepancies are observed beyond outlying drillholes. Therefore, it has been proposed that assumptions regarding extrapolation distance is the main source of mentioned dissimilarities. Key words: Domain modelling, explicit modelling, implicit modelling, indicator kriging, conditional simulation INTRODUCTION Resource estimation is apparently a challenging process calling for extensive expertise and input from several sources, each of which introducing its related uncertainties. In the last decades, substantial role of quantitative analysis of several forms of risk and uncertainty in evaluating projects’ upside potential and downside risks has been realized. Studies indicated that mining companies have been severely impacted because of not meeting project expectations. As noted by Vallee (2000) “… in the first year of operation after start-up, 60% of mines surveyed had an average rate of production less than 70% of designed capacity”. Several other studies on mining projects also revealed that uncertainties related with the resource model are one of the major contributors of mentioned shortfalls. In this perspective, quantification of uncertainties associated with each component of estimation process is critical. 3D estimation domain models capturing major mineralization controls are the fundamental components of contemporary mineral resource estimation. Domain models are key guiding tools for estimation and are products of a complex process involving many unknowns and assumptions. There exists a number of 3D modelling alternatives which are distinct with respect to complexity, time and effort involved. Acknowledging potential influences on downstream mining practices and relavent economic implications, risks and uncertainties associated with 3D domain modelling are critical yet poorly studied aspects.

Jan 1, 2019

By D?Arcy R. George

A survey of the copper mining industry in Western United States revealed that uranium is almost universally present in the solutions resulting from leaching the waste ore dumps to recover copper. The U308 content ranges from about 2 to 15 ppm and a potential production of up to 1,000 tons of U3O8 per year is indicated. A six-week pilot plant test at the Bingham Canyon mine of Kennecott Copper Corporation showed that the uranium is readily recoverable by ion exchange techniques. The design of the new types of countercurrent ion exchange columns and operation of the pilot plant are described.

Jan 1, 1967