Search Documents

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By S. S. Hsieh

As part of a program to address the long-term need to ensure adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial deoiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble that contained about 23% P2O5 and 2.0% MgO. The P205 recovery was 80.8-86.5%.

Jan 1, 1991

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By C. P. Miller

In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about two years ago, approximately ten localities, representing several different types of nickel occurrences were sample, and about 1500 samples of plant and soil were collected. This report will briefly cover the data and results for two areas, and s summary of guides for prospecting.

Jan 1, 1959

By Andrew S. Lain

Before you begin mining aggregates in Oklahoma, you must first look at the market and ask these questions: (1) Is there a need for additional aggregate production? (2) Can we produce the aggregate efficiently enough to compete? (3) Is the deposit close enough to the market? If you can answer "yes" to each of these three questions, then you are ready to start the process for mining aggregates in Oklahoma. The first consideration to be made is whether the aggregates produced will need to meet state specifications. If you do not want to meet state durability standards, there are numerous formations you can mine and produce aggregates. We will deal only with the formations that will meet state durability standards. These formations are located in the southern half of Oklahoma and in the Tulsa area. Some of the formations that contain limestone, dolomite, and sandstone that will meet state durability tests are West Springs Creek, Kindblade, McKenzie Hill, Butterly-Royer, and Rush Springs Formations. Granite and rhyolite also are found in Oklahoma and can be used as construction aggregates. Once an area has been identified as having durable material, and drilling has verified its properties, a permit must be secured from the Oklahoma Department of Mines, Oklahoma Department of Environmental Quality, and any other applicable agency before construction of a plant occurs. There are many different brands of crushers available, but all work on one of two crushing principles-either compression breakage or impact breakage. Each type has its application in different industrial-mineral types and the desired end product. A typical small crushing plant would start with a jaw crusher for primary reduction, and then employ one standard cone and one shorthead cone for secondary reduction. One grizzly would be in the circuit with one finished-product screen and three to four finished-product stackers. Natural sands and gravels are found in rivers and old river channels. These too need to be tested to see if spec product can be produced. All of our sand operations have very little gravel; thus, we do not process the gravel. The sand is processed through classifying tanks for gradation.

Jan 1, 1999

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table's reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck's slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck's slope as a result of the cross flow of wash water at right

Jan 8, 1980

By Dalva L. Moellenberg

Introduction Hard rock mine closure (often referred to as decommissioning), mined land reclamation and financial assurance requirements are receiving considerable attention by governments and organizations around the world. In the United States, federal agencies and the states continue to consider and make changes to laws governing mine closure and mined land reclamation, most of which were originally enacted in the mid-1970’s through the mid-1990’s. Internationally, a number of prominent groups and various countries currently are considering new laws, regulations and policies for mined land reclamation. For example, the European Union has conducted a review of existing European laws concerning mining wastes and mine water and is considering new directives concerning mine waste and mine water management and liability schemes that are likely to significantly impact mine closure and mined land reclamation. Many countries, particularly those outside of North America, Europe, and Australia, have recently adopted or are considering new mine closure and reclamation legislation and regulations. These include significant hard-rock mining countries such as Chile, Peru and South Africa. This paper identifies recent developments in hard-rock mine closure and mined land reclamation laws in the United States, focusing on several of the more significant and controversial developments. It also discusses some of the more significant international efforts to consider mine closure and mined land reclamation laws and policies and some of the notable conclusions and trends from those efforts. The focal issues discussed in this paper include requirements for the reclamation of open pit mines, including backfilling; consideration of and measures to address the mining of sulfide ores and potential for acid mine drainage; and new requirements for the estimation of closure and reclamation costs and for financial assurance for closure and reclamation.

Jan 1, 2005

By R. Hiebert, M. Foote, S. Nordwick, M. Canty

An innovative biological treatment system designed to detoxify cyanide and nitrate and immobilize metals from cyanide leach operations is described. A pilot-plant demonstration was conducted to detoxify cyanide and immobilize several metals from a process stream at the McCoy/Cove Mine. Testing was performed under the EPA’s Mine Waste Technology and Superfund Innovative Technology Evaluation Demonstration Programs. This technology was successful in detoxifying cyanide and effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed. Results show that biological treatment can offer an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1999

By W. J. Douglas

Before discussing minicomputer software for the mineral industry, it is helpful to explain some of the computer program terminology. Most of the terms are the same as those applied to large computers. A computer system consists of a machine (hardware) with electronic and mechanical components and instructions (software) that define its operational logic and sequence. This logic is described by sets of commands grouped into programs. Each program has specific objectives related to the computer's operation and to production information from computer data that are input and processed. Software, therefore, is a general term applied to any type of computer program. Instructions to the computer are communicated through languages that convert logical and arithmetic statements into machine operations. The languages may consist of statements resembling mathematical or logical phrases understandable by humans, or they may be coded statements with no apparent resemblance to spoken language but readily understandable by the computer. Computers also translate higher level languages such as FORTRAN or COBOL into machine languages using other programs called Compilers. Programs written in these higher level languages are generally called source code. However, programs written in computer assembly language may also be called source code. The compiled version of the program after it has been translated by the compiler software is called object code. Programs used to "instruct computers how to be computers" are generally called systems software. They relate more to computer operation than to producing externally usable results. Programs producing information for many users-engineers, accountants, managers-are termed applications software. For the most part, applications software is the principal concern of the mineral industry. Programs are developed to fit user requirements as interpreted by programmers. Programs vary in quality, precision, efficiency, accuracy, and complexity, depending on programmer skills and abilities and programming decisions forcing design tradeoffs. A well written program should have speed, efficient use of available hardware resources, accuracy, and an inherently logical structure that aids documentation and subsequent modifications. Programs developed to fit specific requirements are termed customized software. A program organized and prepared for general commercial use is called a package, or a software package, and includes documentation for program use. A form of customized software that takes an existing program or package as its starting point and modifies it is called a customized package. A minicomputer program can be stored on computer cards, standard magnetic tape, magnetic cassette tape, floppy disk, or hard disk. The software purchaser or lessee may select one or more of these media when specifying a program in a software contract. Supporting documentation may include a listing of the program instructions linkages, hardware and storage resource requiremnents, flow charts, and programmer and user manuals. The purchaser must carefully make and clearly understand specifications for media and format of program delivery. This assures that delivered software is compatible with the intended hardware. Mineral Industry Attitudes Toward Computer Software The mining industry has traditionally been conservative concerning computer applications. Furthermore, large computer costs have made these systems accessible only to large companies, for the most part. But in the past few years, mining software systems developed at schools such as Pennsylvania State University and Virginia Polytechnic Institute have gained wider acceptance in the mineral industry. More mining engineers now have academic training in computer application, and computer use is now more acceptable to the mining industry. Mining managers in decisionmaking positions are faced with a new generation of computer technology resulting from the rapid evolution of minicomputers. Not too long ago, manufacturers such as Digital Equipment Corp., Data General, and Hewlett-Packard were considered newcomers. They are now established companies. In addition, Apple, Radio Shack, Commodore, and others have emerged in the growing microcomputer industry. So the mine manager or mining executive now has more options. Mining Software is Limited Along with the rapid evolution in hardware development, much general purpose software is now being developed for minicomputers. The 1981 Apple Software Directory can be obtained for about $14; Radio Shack published the Application Software Source Book in three volumes for $1.95 each. Brochures describing software can be obtained for other minicomputer manufacturers by contacting local sales representatives. Hewlett-Packard software can be obtained and exchanged through HP user's groups. Manufacturers' programming staffs are generally concerned with developing applications software. In some instances, manufacturers will recommend software developed by their hardware users. Until now, however, software development for mining applications has been minimal. This should not be surprising, since software development traditionally lags hardware development by several years. A review of A Directory of Computer Software Applications/Mini-Computers and Micro-Computers, August 1977-1980, published by the US Department of Congress, National Technical Information Service, contains many entries and subject areas. General applications include some references to tunneling machines, but there are virtually no entries specifically relating to

Jan 11, 1981

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By Roderick K. Davey

Kennecott Copper Corp.'s Metal Mining Div. operates three major open-pit copper mines in the western United States. These operations include Utah Copper Div., Ray Mines Div. in Arizona, and Chino Mines Div. in New Mexico. At each of these operations, the material is loaded by large electric shovels and transported by both truck and rail haulage. In 1977, 197 350 774 t (217,542,000 st) of ore and waste were mined at these operations, and 302 040 t (332,942 st) of copper were produced. Also a significant amount of molybdenite was produced as a byproduct. In operations as complex and large as these, there is an inherent need for up-to-date reports concerning how much material was mined during the previous day, and year-to-date, what equipment is scheduled for maintenance, how equipment has been performing, etc.

Jan 1, 1979

By William M. Greenslade

As the search for minerals leads to deeper mines the need to control water inflow into mine shafts and mine workings will grow. As shal¬lower more readily available minerals are exploited, ore bodies which were previously uneconomic be cause of their depth will now become attractive targets. In known mining districts new ore bodies are being discovered down dip of existing ones. In the west many metal deposits are being developed in rocks of the mountain front pediments, frequently covered by several hundred feet of saturated alluvium. Greater depth often means that workings are developed well below existing water tables, creating high hydrostatic heads adjacent to mine workings. The purpose of this paper is to review some of the methods available for determining if water control will be necessary and to present some of the techniques for locating water bearing zones and the amount of water to be expected. The paper will concentrate on problems associated with water control in mine shaft development, although many of the exploratory techniques are similar to those needed for assessing overall mine water inflow problems. A brief case history on water control problems in mine shafts in the Grants mineral belt of northwestern New Mexico is presented. Water control during shaft sinking presents some unique features. First, the problem is a relatively short term one, since water control is often necessary only while the shaft is being sunk. Control measures may be necessary only while the shaft is open into the water bearing zone and the lining installed and cemented. Secondly, limited working space within the shaft area presents difficulties in handling large amounts of water inflow. The presence of water in the shaft working area increases sinking time and the potential hazard to miners. Finally, there is the economics of shaft sinking. While the shaft is being sunk no ore is being produced and there is every incentive to minimize costs.

Jan 1, 1979

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By Tim O’Neil

Many mining companies try to fight their way up from small operator and exploration company to major producer. Not many companies make it. Cambior Inc., formed in 1986, is one company well on its way to making it as a major operating company. In 1993, Cambior surpassed 15.5 t (500,000 oz) of gold production and began operations at its world class Omai gold mine in Guyana. At the same time, the company has embarked on a program of geographic and minerals diversification. Cambior, a Canadian company, now has interests in eight mines, three development projects and more than 100 exploration properties in North and South America. The company’s goal is to derive 70% of its income from gold and 30% from base metals and other minerals. Cambior’s moderate diversification into base metals gives protection against negative gold price fluctuations. It also balances the typically short term gold mines and the longer term base metal mines.

Jan 1, 1994

By Thomas O’Neil

Part 2 of this article continues with a discussion of features that distinguish contemporary investment analysis in mining from earlier methods. Part 1 traced the evolution of evaluation methodology from the traditional and discounted cash flow methods to the present. Quantitative investment models of the past 20 years played an important role in mine evaluation, but a new integrated approach to mine investment decision-making is now developing because of growing economic, technical, and political uncertainties. One of those uncertainties -inflation-was discussed in Part 1. Increased Risk At a time when mineral production technology and analytical evaluation tools have never been more sophisticated, it may seem anomalous to claim that mining ventures are riskier. Whereas technical risk has, indeed, been notably reduced, business risk the chance of a major loss due to market factors-has increased. This has been caused by two factors: the rapidly rising capital requirements of new projects and increasingly unpredictable future economic conditions. These difficulties are compounded by the long lead times of large, new mining projects. Rising Capital Requirements A $100 million investment is no longer considered to be a large mining project in most cases. For a large metal mining project, the total cost of the concentrator alone can exceed $100 million. Amoco Minerals' Thompson Creek molybdenum mine being developed in Idaho will cost over $350 million, for a relatively modest sized (23-kt/d or 25,000-stpd) ore operation with no extraordinary features. For a major grass roots copper operation producing blis¬ter or refined copper, the capital requirements are billions of dollars, not millions. Project costs are higher for two reasons. One, the projects themselves are larger; and two, the capital cost per unit of production is rising rapidly. Projects are larger because lower grade ores, yielding smaller margins, must be mined in greater volume-particularly in view of the high fixed costs of modern technology. When analysts contemplate any capital project, an important consideration is the minimum economic size of the facility. This is the smallest size that can be built and still be competitive on a total unit production cost basis. In the conventional copper smelting business, for example, a production rate of at least 91 kt/a (100,000 stpy) of blister copper is about the absolute minimum for reducing unit fixed costs to competitive levels. Clearly, many variables affect the minimum economic size of a mining facility, but with few exceptions that size continues to grow. Unit capital costs of new mining projects also are continuing to rise. The accompanying table shows that the capital costs in primary copper production have risen faster than the cost of living. Of particular note is the capital charge of over $1.70/kg (77411b) required for a new, fully integrated facility in 1981. Thus, the mid-1982 copper price would not even cover the cost of capital for a new copper producing complex without considering the direct operating costs for such a facility. The breath-taking costs of new mining projects are caused by factors such as increasingly complex technology, the rising social costs of creating attractive living and working conditions for employ¬ees, and the expenditures re¬quired for environmental protec¬tion. For whatever reasons, how¬ever, unit capital costs in mining continue to exhibit staggering growth rates. Future Economic Conditions Risk is not only a function of the size of the potential loss-an im¬portant measure of which is the capital intensity of mining dis¬cussed above-but also of the like¬lihood of incurring the loss. It is here that the ever increasing lead times of mining projects and the glaring limitations of economic forecasting are so important. In comparison to nearly all other in¬vestments, mining has more capi¬tal at stake for a longer period of time before commercial uncer¬tainty is resolved by distant eco¬nomic conditions that are subject to high forecasting errors. A sobering example of the pre¬ceding points occurred with the Lakeshore copper mine in south¬ern Arizona that Hecla Mining Co. undertook to finance and manage in 1969. The project was a joint venture of Hecla and the El Paso Natural Gas Co. and included two mines-one producing oxide ore and a second in the sulfide zone¬and a complex processing facility producing both electrowon cop¬per cathodes and copper precipi¬tates. The project originally was

Jan 12, 1982

By C. E. Jordan

The Bureau of Mines has investigated the fundamentals of fatty acid/fuel oil conditioning for improved flotation selectivity. Both conditioning time and intensity can provide optimum flotation selectivity as well as good recovery. Traditional conditioning seeks to optimize conditioning parameters with subsequent recovery of the hydrophobic mineral. In the fatty acid/fuel oil system many silica gangue particles are also rendered hydrophobic by the flotation collector. Fundamental studies have shown that particle-particle collisions transfer the collector reagents selectively to the mineral surfaces with the highest affinity for the reagent. This mechanism deactivates the gangue particles while increasing the collector reagent loading on the selected mineral. The degree of this transformation is directly related to the number of particle-particle collisions which can be controlled through conditioning time or conditioning mixing intensity.

Jan 1, 1995

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By J. Y. Hwang

Processing of fine mineral particles in a slurry is a difficult problem. Methods to make fine particles magnetic have been developed recently and may offer a solution to this problem. Particles of nonmagnetic materials can be selectively rendered magnetic through surface interactions with magnetic reagents. When adsorption occurs, the magnetic susceptibility of the material is increased. Magnetic enhancement at several orders of magnitude can be achieved. Selectivity of the adsorption can be controlled by the functional groups of magnetic reagents and various surface interaction mechanisms. This approach allows a new degree of freedom for the processing of fine mineral particles, even with conventional magnetic means. Separation of valuable minerals and filtration of slimes from tailing ponds and recirculated water are examples of the applications. Basic principles of this technology are discussed in this study.

Jan 1, 1992

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016