Search Documents

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By S. T. Krukowski

Traditionally the lime industry is governed by market, location, and transportation. These factors also may act as obstacles to global market access. Lime manufacture responds to market opportunities by first focusing on location. Lime markets are diverse and widespread, and ubiquitous occurrences of limestone make development of a widespread industry possible. Lime’s low to moderate unit value restricts transporting it long distances. Other factors (including lime reactivity, dedicated container use and other liabilities) limit shipping lime far. In the past many small to medium size companies made lime for local use. Today the global aspect of the industry is ownership by few large companies producing lime for local consumption.

Jan 1, 2003

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By H. L. Owens, J. W. Fredland, K. K. Wu

The Mine Safety and Health Administration (MSHA) is responsible for reviewing and approving the engineering plans for impoundments, of significant size or hazard potential, that are constructed on coal-mine property. Over the years, technical review criteria have been updated as the state-of-the-practice for dam safety has evolved. The evaluation of stability under earthquake loading, for example, has gotten much more sophisticated for impoundments built using upstream construction. Recent incidents where slurry has broken into mine workings have caused MSHA, mine operators, and design engineers to re-examine this safety issue. This paper gives an overview of MSHA’s impoundment plan review process.

Jan 1, 2003

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By James A. Erdman

This overview briefly describes some examples of applications and difficulties in using plants that are drawn from the literature and from field experience. Because of the generally low Au concentra¬tions found in plants, the analysis of plant tissue is critical to the successful application of the biogeochemical method of prospecting. Neutron activation analysis is the most widely used method to detect Au in plants, due largely to its sensitivity; levels in the parts per billion range are easily attained. Two general types of sampling media are used in prospecting for Au: humus and living plants. Humus has been widely used in Canada, but the sampling of plants has increased there and elsewhere in recent years. The use of douglas-fir (Paeudotsuga menziesii) at a Au-bearing stockwork in Idaho is a prime example. A maximum Au concentration of 14 ppm was detected in the wood ash of this coniferous tree, well above the normal background concentration of about 0.15 ppm. Among shrubs that might be useful in Au prospecting, sagebrush or wormwood (genus Artemisia) could be sampled because it is extremely responsive to concealed mineralization. It has been used extensively in the Soviet Union and could be used in areas of the western United States where disseminated Au occurrences might be located. Among the problems one may encounter in using plants for Au prospecting are (1) physiological barriers, by which many plant species simply do not absorb Au at detectable levels; (2) misconceptions of soil-plant correlations; (3) localization of Au in plant tissue; and (4) the variation of Au concentrations due to season. Despite these limitations, biogeochemical techniques can complement or replace other geochemical methods currently used.

Jan 1, 2013

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By Ralph Loyd

One of the principal responsibilities of the California State Geologist is to provide local governments with maps and information regarding mineral resource occurrences within their jurisdiction. The primary objective of this effort is to furnish basic data that is essential in planning for and accommodating wise development of mineral deposits that are important to the economic well-being of the region, state, and nation. Local government agencies are required by law to incorporate the information provided by the State Geologist into their general plans and formulate mineral resource management policies that emphasize conservation and development of mineral deposits. The Mineral Land Classification program was initiated by the State Geologist in 1977 under authority of the California Surface Mining and Reclamation Act (SMARA). To date, about 33,000 square miles of land have been classified for mineral resource potential. Most of the mineral land mapping has been conducted in three principal areas: (1) metropolitan areas of the state where urban encroachment has greatly diminished available supplies of construction aggregate; (2) Sierra Nevada foothills, a region that is undergoing dramatic population increases; and (3) the Mojave Desert and Great Basin regions, where large Federal land withdrawals are pending that could preclude mining. Mineral land classification studies address the overall mineral potential of a region through the identification of local and regional geologic factors that control or influence the formation of mineral deposits. These studies are field-intensive surveys that enable project geologists to gain first-hand knowledge about the nature and distribution of mineral deposits in a given area and portray that information accurately in map form. This paper summarizes the progress made in the Mineral Land Classification program in the metropolitan, Sierra Nevada foothills, and the Mojave Desert/Great Basin regions of California. Selected projects from each area are discussed in detail.

Jan 1, 1995

By W. L. Oliveira, J. R. Sobrinho, V. M. Hamza, S. M. Eston

The Ipueira III chrome mine is located in the northeastern part of the state of Bahia, Brazil. Extraction is actually at depths less than 300 m, but below level 200 serious environmental problems have been encountered with respect to control of air quality, toxic gas, dust and thermal comfort. At the request of the mining company the University of São Paulo started a research program to investigate the origin and occurrence of the critical problems and to propose solutions. A ventilation survey was carried out first which revealed the existence of several air leakages and short circuits that contributed to substantial reductions in the air supply to some of the main producing levels. Computer simulation of the ventilation network showed that extending the intake air shaft to deeper levels was the most convenient and economic solution to improve the air quality. The ventilation survey was followed by a mapping of the toxic gas emissions and thermal comfort levels in several parts of the mine. The air quality conditions were evaluated as a function of gas emission and heat generation associated with production and development activities. The results show that environmental conditions are already critical in most of the working levels and neither an increase in production nor deepening of the mine can be taken up without substantial changes in the ventilation system. INTRODUCTION Environmental concern is growing in Brazil and several underground mines are starting environmental engineering programs. The LACASEMIN - Laboratory of Environmental Control and Mine Safety of the Mining Engineering Department of the University of São Paulo - was contacted by Mineração Vale do Jacurici to start a research program for investigating the origin and occurrence of environmental problems that existed in the Ipueira III chrome mine. This research program involved field measurements of air quantities with gas levels monitoring, evaluation of heat stress parameters, determination of adequate flow patterns through computer simulations and training of mine technical staff. This paper presents the results of the first 4 months of this research program. The Ipueira III mine is located in the northeastern part of the state of Bahia, near the city of Senhor do Bonfim at about 400 km inland from the state capital city of Salvador. Chromite mineralization is quite widespread in this area and often associated with mafic and ultramafic rocks which cut across regional gneisses and migmatites. ROM production in 1992 varied between 25,000 to 40,000 tons per month, 25% being of lump type (38% of Cr2O3) and 75% being of fines. Lump is manually separated and fines are concentrated in a nearby plant. All the production goes directly to the group processing steel plants near Salvador. The Ipueira III mine is currently under some adverse economic situation because of imports from South Africa and Russia, which have better grades and sometimes a lower content of phosphorous. Consequently there has been little progress in the development of new mines and even in those currently under operation the extraction is becoming more difficult due to the lack of investment in improving mining methods and ventilation systems. In spite of such difficulties the company has backed up studies for initiating an environmental engineering investigation of the Ipueira III mine. MINING METHODS AND VENTILATION SCHEMES The mining methods adopted have changed as a function of extraction depth, rock mass strength and ore body geometry. Initially the orebody was found to be fairly continuous and dipping at about 55 degrees from surface

Jan 1, 1993

By Malcolm Roberts

Extensive personal experience in the USA and Australia has shown that Australians working in suitable work environments are capable of world class performance. To build such work environments, mining leaders need to ditch two common management approaches that have not succeeded. Firstly, stop relying on traditional methods of trying to change people's behaviour simply by using communication alone to change attitudes and then change behaviour. Analysis of human behaviour explains why this approach fails in all industries. Secondly, stop trying to improve productivity by just running harder and increasing capital investment. Understanding work processes explains why this approach has limited success. These two approaches underlie problems commonly mentioned by many Australian mining executives: • negative or inadequate attitudes prevailing among Australian miners and managers including the lack of ownership of business goals among people at many levels • inadequate development of managers and accountability • lack of a competitive advantage in an industry in which labour costs are around 50% of mine site cash costs at many mines, and, • logical, emotional and physical barriers to change.

Jan 1, 1995

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By Paul Higley

Specialty Devices, Inc. and the CMRET/NIUST, University of Mississippi, have collaborated in the design and development of a new class of Robotic Underwater Vehicle (ROV) focusing on efficient, low cost, deepwater operations. The need for such a vehicle was driven by special requirements encountered in the establishment of the Gulf of Mexico Gas Hydrates Research Observatory at a depth of 850m in Mississippi Canyon Block 118 on a restricted budget. Requirements included deployment and recovery of tools and sensors and the connection of underwater-mateable electric and fiber optic connectors at depth. The standard complement of equipment required included; high-resolution video with lighting, scanning sonar, robotic arm, precision positionin and thrusters for limited transit and maneuvering. Conventional deep water ROVs are lowered in a large cage with a buoyant tether between the cage and the ROV. The tether is wound on a winch in the cage deployed as the ROV swims out from the cage. This cage is lowered on a large diameter umbilical cable with strength elements and communications elements and conductors for electric power. With increasing water depth the umbilical cable must become ever larger to accommodate increased power transmission loads and strength demands, with corresponding increase in deck handling equipment size and in turn, vessel size and overall cost. The surface ship must include a dynamic positioning (DP) system to control ship propulsion to maintain the position of the ROV cage at a position relative to the sea floor. DP ships with this capability and the ability to carry the large umbilical cable and winch are expensive.

Jan 1, 2008

By K. J. Stratford

The selection of a suitable mathematical function for the modelling of the partition curve for dense medium cyclones is discussed. Five alternative functional forms (based on three basic functions) are compared using data obtained in the course of an extensive experimental study of a 610mm dense medium cyclone. It is shown that, for adequately sampled tests, any of the functions may be used, although a function based on the Weibull distribution is shown to be most suitable. Where data are poor, all functional forms exhibit disadvantages, notably in terms of a reduction in precision of parameter estimation. This problem can be exacerbated by the complex numerical techniques required to estimate the parameters of a particular function. A set of ideal requirements for a performance function are presented.

Jan 1, 1986

By Qing Wang

Open pit mines require substantial capital investment at the beginning of the operation and replacement investment at later years. The objective of obtaining the highest possible return on investment in a mining project can only be achieved with an efficient long term production plan. This plan consists of optimally determining four principal elements: 1) the amount of ore and waste to be mined each year, 2) the specific blocks to be mined each year, 3) the optimum mine life, and 4) the ultimate pit limits, which delineate the total reserve to be mined. The existing methodologies only provide solutions to one or two elements, by assuming the others known. Furthermore, the cost of mining each block in the deposit is assumed to be known and independent of the production schedule. The four elements of production planning are interrelated and the cost of mining any block is a function of the production schedule. The ultimate goal of this study, ,whose first steps are&apos; discussed in this paper, is to develop a solution methodology that can simultaneously optimize all four elements of the production planning problem in open pit mines without making a priori assumption on any of the four elements.

Jan 1, 1992

By A. L. Muler

Since 1956, when Broadbent and Callcott 1 proposed to analyze breakage processes by matrix methods, several authors and their co-workers have proposed various models of grinding that, in principle, could lead to fully automated grinding circuits. In particular, Meloy and Gaudin2, Gardner and Austin3, Kelsall and Reid4, Neloy and Bergstrom5, Callcott and Lynch 6, and Draper and Lynch have, by either computer simulation or by experimental data, or by a combination of the two, verified that comminution is reasonably well described by at least two functions: a selection function and a breakage function. The stage concept proposed by Callcott and Lynch6 requires that a classification matrix be included to completely describe breakage in an open circuit rod mill. The purpose of this work, portions of which are herein described, is to accumulate sufficient information on the breakage characteristics of quartz and magnetite in an open circuit rod mill, so that several of the theoretical and experimental approaches proposed in the literature can be compared with each other. Data is being gathered to compare the experimental method used by Kelsall and paid against the stage approach of Callcott and Lynch.

Jan 1, 1968

By Sukumar Bandopadhyay

In recent years, research in the field of artificial intelligence (AI) has had many important successes. Among the most significant of these has been the development of powerful new computer software known as the "expert systems". Expert system programs designed to provide expert-level consultative advice in mineral exploration (Duda et al, 1981), scientific (Feigenbaum, Buchanan and Lederburg, 1971) and medical (Shortliffe, 1976) problem solving are generally acknowledged to be among the forerunners of this research. As the decision makers virtually in all fields face a more complex and involved world within which to operate, the need for some decision support is also becoming urgent. Thus applications of expert systems continue to spread out reaching problems that, because of their dimensions or particular aspects, set more demand on the decision methodologies. To meet these new requirements, many activities which were performed in the past by the domain expert or engineer must become automated. Furthermore, previous research (Dawes and Corrigan, 1974; Dawes, 1979) has shown that automating an expert&apos;s decision rules often provide better decision than the expert does. For large systems it would be very useful (or even necessary) to have formal tools, allowing one for example, to automatically discover inconsistencies, contradictions or redundancies, or to identify the possibilities of wrong lines of reasoning in the decision process.

Jan 1, 1990

By Christopher J. Hall

It has been known for a long time that summing pressure drops and rises due to friction, shock, fans and natural ventilation is incorrect. In fact, lost works and works should be summed. In spite of this, the traditional method of finding a fan/system operating position has been the H/Q Curve. This paper presents (lost) work/m curves, progressing from a single fan moved around the system to include natural ventilation work, and fans in a series, parallel and series/parallel. The solutions obtained graphically are substantiated by dry air thermodynamic solutions, and the traditional solutions are shown to be in error. This method of solving problems is particularly useful when moving fans around the system, and essential in series/parallel and series situations with substantially different fan densities. The dry air analysis is employed because of its simplicity. Real air, with evaporation and condensation, will react somewhat differently, and one should use real densities (i.e.[l + w +w]/va ) when using this method. One source of error when applying this method to real air, although probably not major, will be investigated in a subsequent paper. Friction and shock losses are proportional to the square of the mass rate of flow, leading to the typical parabolic system curve. However, the unbalanced water stuff potential energy term, on a unit mass basis, is substantially independent of the mass rate of flow. It is possible that this could be handled as a negative natural ventilation work.

Jan 1, 1987

By Campbell J. McKenzie

Following on from the successful completion of three exploration programs and the discovery of two new inactive Seafloor Massive Sulphide (SMS) deposits within New Zealand?s Exclusive Economic Zone (EEZ), Neptune is now poised to take the next step from explorer to developer. Neptune considers that commercialization of SMS deposits represents the future of the mining industry, providing a new source of metals to the world economy, and enabling host countries to benefit from this new industry. Neptune recognizes that marine biodiversity is among the greatest treasures of New Zealand. The geological isolation, range and complexity of habitats, and a number of major ocean currents that influence New Zealand have created diverse marine communities. Neptune, recognizing both the environmental importance of marine biodiversity and the value it provides to all New Zealanders has made commitments to ensure sustainable development. There are many unanswered questions regarding how the marine environment may be affected by SMS development, however best practice environmental management is a key aspect of the Company?s approach to our activities and the code for ?Environmental Management of Marine Mining? prepared by the IMMS has played a part in this approach. Neptune has close relationships with the scientific community to ensure that appropriate environmental strategies and plans are developed in order to minimize the effects of our activities on the environment.

Jan 1, 2008

By Victor F. Hollister

This section on case histories of discoveries of volcanic-associated and volcanogenic massive sulfide deposits is divided into a preliminary discussion of models and then into three parts: Kuroko- type, Anyox-type, and shale-hosted. The separation is made to accommodate the use of exploration models, and these may not coincide with genetic models discussed in the literature. The exploration models grew as knowledge was gained concerning ore guides and ore controls in the volcanic-related deposits. The evolution of the genesis of massive sulfide deposits in volcanic terranes from a replacement to a syngenetic hypothesis in the 1950s and 1960s necessitated changes in exploration approaches in ore search. The acceptance of a syngenetic origin for conformable or concordant sulfide masses led to more widespread adoption of stratigraphic ore guides. &apos;The occurrence of epigenetic stringer ore with and stratigraphically below many conformable massive sulfide deposits did not diminish the importance of stratigraphic ore controls. Proximal conformable sulfide masses were formed near their seafloor hot spring source and normally are underlain by epigenetic sulfides: whereas. distal conformable sulfide masses were deposited away from the hot spring and may have no associated feede; zone. Industry groups that early recognized the syngenetic nature of volcanogenic massive sulfides were responsible for discovery of some of the large and economically significant deposits. Ultimately, the rest of the geological profession accepted the leadership of the early iconoclasts.

Jan 1, 1991