Search Documents

By Ken Deter

My recent experience has been with wet tropical environments, which address a different set of concerns than Nevada, for example. Spraying rather than drips are required in most cases just to assist the water balance requirement, and my comments address those situations. Most tropical operations are faced with both extremely wet and very dry seasons, with some having multiple cycles during the year. A heap leach operation must address the rate of solution building up within the ponds and how long the volume must last until the next rainy season. It may be easier to construct sufficient pond volume to permit yearlong operation than by discharging excess solution now, and searching for water later. Pond capacity requirements can help with the following: Consider using the solution that could be locked up in the pads during leaching to assist water balance problems. Spray excess solution continuously onto spent ore that would not be normally be sprayed again to "soak up" the excess solution, and stop spraying when the water balance is low, allowing the solution in the spent ore to return back into the system-with or without cyanide added. In a multiple lift system, if intermediate HDPE liners are planned for solution grade control, have drips placed before the HPDE liner is in place. The drips can distribute excess precipitation throughout the lower lifts to control the water balance, while the most current lifts are being leached and sent directly for the preg pond. With only 2 million tonnes (2.2 million tons) of spent ore involved, up to 200,000 cubic meters (53 million gallons) of solution could be moved into or out of the water balance system, if proper methods are designed and installed. That is equivalent to one meter (40 inches) precipitation falling on a 200,000 square meter (2.2 million square feet) pad area. You may even get a little bit more gold recovered as the solution drains from the earlier pads, as well.

Jan 1, 1999

By J. E. Warm

Florida’s ancient beach ridge sand deposits, mined for construction aggregate, are highly variable. Rinker Materials utilizes a small reverse-circulation drill rig to prospect and profile unconsolidated fine aggregate deposits more effectively and inexpensively than other drilling methods. Sample data is stored in a spreadsheet that calculates yield and volume. Rinker also uses a Trimble ProXR backpack GPS to locate boreholes in the field, track mine progression on a monthly basis, and to map restrictive features such as wetlands. Autodesk Land software is used to create detailed deposit maps and mine plans. Rinker believes that these practices have led to improved awareness of deposit characteristics and deposit utilization.

Jan 1, 2004

By John E. Tilton

Looking back on the second half of the 20th century, future historians, I believe, will be fascinated by two major political upheavals. The first is the environmental revolution in the 1960s. It erupted in the United States and parts of Western Europe and then swept across the rest of the globe like a wild fire. The second event is the collapse of the Soviet Union. It was the last of the world's great imperial empires. With its demise went central planning as a viable economic system. History, I suspect, will see this second revolution as an offspring of the first. This is because economic and environmental issues were largely responsible for the unraveling of the Soviet Union.

Jan 1, 1994

By Larry Lynott

This paper summarizes the benefits ofusing an in-situ analyzer in a sampling and valuation program. The tests and studies cited quantify the problems associated with current conventional sampling techniques and contrast conventionally-obtained results with those obtained through in-situ analysis. Data are presented to show the improved precision in valuation resulting from the in-situ method. Greater precision in estimating the mineral content of unmined ground becomes increasingly important as mines strive for optimum exploitation of their deposits. As the following analysis shows, the variable distribution of minerals within a deposit, along with the difficulty and the cost of high density sampling limits the precision which is currently possible in practice. An inherent problem exists in the conventional method of sampling. The erratic values of ore grade necessitate the collection oflarge numbers of samples for statistically accurate valuation and ore reserve estimation. Owing to the cost of manpower, current sampling techniques do not allow for the collection of sufficiently large numbers of samples. The most common method of sampFng in current practice is chip sampling, although bulk sampling is sometimes used. The intent of sampling is to obtain an estimate of the value of blocks of ground prior to mining. This information is used to plan the rate and sequence of mining, yet the sampling intervals which are possible in practice cause these block estimations to be ubject to considerable uncertainty. This inevitably leads to mcorrect mining decisions which may be vy costly.

Jan 1, 1998

By Guangming Zhao, Nianjie Ma, Demao Guo, Denghong Chen, Yingming Li

Based on the mechanical essence that large-scale plastic failure zone appears in all or part of surrounding rock in soft rock roadway, the numerical simulation method is used to study the rectangular roadway in layered rock strata. It is clarified necessary conditions must be met for soft rock: firstly, the strength condition is that the maximum confining pressure is greater than the uniaxial compressive strength of rock strata. Secondly, the stress environment condition is that the ratio of maximum confining pressure to minimum confining pressure is greater than 3. Thirdly, the angle condition is that The direction of principal stress action enables the plastic zone of weak rock layers to fully develop. At the same time, the quantitative description method of soft rock is given, and the soft rock roadway is redefined. Soft rock roadway refers to the roadway that meets the strength conditions, stress environment conditions, and rock structure angle conditions under certain surrounding rock conditions and in-situ stress environment conditions. After the excavation of the roadway, a large-scale plastic failure can be formed, that is, a butterfly-shaped plastic zone is formed, and the conventional support cannot be adapted. It is difficult to support in engineering. It provides a theoretical basis and engineering analysis method for the identification of soft rock roadway, and the research results have engineering value Soft rock tunnel engineering in coal mines constitutes a vital aspect of soft rock engineering. This field broadly encompasses rock engi- neering concerning large plastic deformations, e.g., soft rock slope engineering and soft rock tunnel engineering. The intricate geological conditions encountered in soft rock tunnel engineering present a significant challenge to support, which has harmed coal production in China. China leads global raw coal production with the annual output of 4.6 billion tons. Annual tunnel excavation supporting this production spans approximately 11,000 km, with over 10% of these tunnels classified as soft rock formations. Soft rock is commonly associated with soft rock tunnels due to their prevalence in engineering projects. However, reaching a consensus on the definition of soft rock has long been an enduring challenge for scholars and engineers. Numerous definitions have been proposed, includ- ing descriptive, index, and engineering definitions. For instance, the International Society for Rock Mechanics defines soft rock based on its uniaxial compressive strength σ ranging from 0.5 to 25 MPa. China's Engineering Rock Body Standards, established in 1994 (GB 50218-94), take a qualitative and quantitative approach to classifying rocks. Rocks are categorized as hard or soft based on criteria such as hammering sound, fragmentation, water immersion effects, and weath- ering degree. Additionally, the integrity of rock bodies is assessed across five categories intact, relatively intact, soft fractured, fractured, and extremely fractured. This classification considers factors like the number and spacing of structural planes, their combination, and the types of structures. Descriptive and index-based definitions fall under the category of geological soft rocks, providing a comprehensive geological perspective on the surface features or strength characteristics. However, these definitions have limitations in engineering practice, which leads to contradic- tions. For instance, rocks with uniaxial compressive strength less than 25 MPa may not exhibit soft rock characteristics if the tunnel is shal- low with low horizontal stress levels. Conversely, rocks with compressive strength exceeding 25 MPa at sufficient depth and high horizontal stress may exhibit soft rock characteristics. Definitions originating from engineering practice have emerged after realizing the inadequacy of discussing soft rocks without considering engineering. For instance, Dong's loose circle theory defines soft rocks as rocks with a loose circle thickness exceeding 1.5 m, which chal- lenges conventional supports. This intuitive definition, widely accepted by engineering professionals, emphasizes the difficulty in supporting tunnels due to extensive damage. However, various tunnel damage poses a challenge in relying solely on the loose circle thickness of tunnels for determining soft rocks. He introduced the concept of engineering soft rocks, which are defined as rock formations exhibiting significant plastic deformations under applied engineering force. Two fundamental mechanical properties of soft rocks are identified the critical softening load and critical soft- ening depth. Rocks below the critical softening load threshold are categorized as hard rocks, while those exceeding it exhibit substantial

Jun 25, 2024

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By G. Le Bel

Discussion by G. Le Bel The paper proposes three methods to determine optimum lifetime of a mining project 1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: •It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. •The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate. Discount rate selection The opportunity cost of capital represents the rate of return that would be obtained if the capital was instead invested in other opportunities considered to exist. Such opportunities must be bypassed if the available capital is invested in the project studied 2. If these other opportunities carry risk similar to the project under analysis (for example, if they are other mining projects), there is no need to add incremental [ ] risk factors. On the other hand, if these opportunities are represented by the acquisition of government bonds yielding 7%, a risk premium factor must be included. The types of risks associated with a mining venture are shown in Table 1. Together they represent the "business risk" of being a mining company. The individual project risk is important to investors if it differs substantially from the business risk of the company and that of the other investments in mining ventures that we must pass up to invest in this particular project. A risk premium or discount would then be required. This can be illustrated by the following example. Consider that a company has two investment alternatives: one is the Cavender hypothetical project located in Nevada, and the other is the same project located in a civil war zone of central Europe. The second project requires a risk premium factor on the discount rate. Conversely, a project showing highly uncertain returns that are negatively correlated with the returns of the firm's other assets may decrease the company's corporate risk. Deterministic character of NPV calculation The cash flows used in NPV calculations are obtained from a set of variables. These variables are estimated using one parameter obtained from the engineering studies. Each parameter is thus a single value that is often termed a "realistic" or "best estimate" as opposed to "optimistic" or "pessimistic." However, considering that each variable can assume a range of values between the

Jan 1, 1994

By Ian Mitchell, Peter Faganl, Paul Haddad, Rob Dunne

During the gold cyanidation process, cyanide can be lost from the leachate by various chemical routes. The products of these cyanide losses include base metal cyanide complexes, thio­cyanate and cyanate. These losses are particularly important when treating pyritic or cupriferous ores since the two most sig­nificant cyanic ides, in order of importance, are sulfides and cop­per bearing minerals (I). Cyanidation of pyritic minerals results in the formation of thiocyanate. The problems caused by cyanide soluble copper minerals are well known to the gold processing industry and have been reviewed by several authors (e.g. 2, 3). An important consider­ation, especially with a number of more recent leaching tech­nologies, is the effect of the CN :Cu mole ratio, R, on the gold leaching kinetics. In order to efficiently leach cupriferous ores, it is important that R is maintained at a level that allows suffi­ciently rapid leaching without excessive use of cyanide. The optimum value for R in a fixed leaching system would appear to lie between 3 and 4. This is based on the early observations that the leaching rate is very slow when R is below 3, with a rapid increase in the leaching rate above 3 (2, 3,4). The leaching rate increases gradually when R is greater than 4 (4). The major Cu(I)-cyanide complex in this range of R values is the [Cu(CN)J]2· species. It has been postulated that leaching occurs due to either uncomplexed cyanide or the fourth ligand in [Cu(CN)4]3·, since the stepwise formation constant for this complex is very small (2, 3). An additional consideration when leaching cupriferous ores is the oxidation of cyanide by Cu(II) minerals, resulting in the formation of cyanate. It has also been reported that both sulfide minerals (5) and activated carbon (6, 7) catalyse the oxidation of cyanide to cyanate. From the above discussion, it is important for the leaching con­ditions to be carefully controlled when treating pyritic and cuprifer­ous ores in order to achieve efficient and economically viable leach­ing. For example, large concentrations of thiocyanate in the leachate would reveal large cyanide losses and thus indicate the need for a pretreatment step to oxidize the sulfides. Alternatively, a low R value would indicate slow leaching kinetics and consequent low gold recoveries, indicating the need for increased cyanide dosage.

Jan 1, 1996

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material's flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By William N. Poundstone

Consolidation Coal Company, through the mining research division of Continental Oil Company, is now undertaking the installation of a full-scale hydraulic transportation system to carry coarse coal from the mine face to the preparation plant. The facility will include all elements of a fully integrated haulage system including face haulage for both longwall and continuous miner sections, multiple slurry feeds, hydraulic hoisting and 2.4 miles of overland slurry transport. This undertaking is a result of more than six years of extensive research and testing, some of which has been previously releasted to the literature. To provide a reference framework for system description, a brief history of recent coal mining technological developments will be discussed. Following World War II, mechanization resulted in mining machines that were bigger, faster, more powerful, and more reliable. These changes were essentially refinements in an established mining system. They made mining more efficient than before, but they did not change the system itself. By about the mid-1960's, it was apparent that further improvements in the extraction machinery would have a declining payoff, simply because .the worst bottlenecks were in other components of the mining system. A modern continuous miner cannot be run continuously because other operations underground cannot keep pace. In fact, most continuous miners today run at less than 20% of capacity. Consequently, in 1969 Consol and its parent company, Continental Oil, undertook a long-range R&D program to try to change the basic haulage system for the better. Most coal at present is removed from the mine by a hand-off system in which the coal is transferred from the continuous miner to a shuttle car, often with the aid of a separate loader; then from the shuttle car to a system of conveyor belts; and finally from the conveyors to rail cars. The system involves a large amount of moving equipment underground, many transfer points, and the everpresent chance of operational delays and safety hazards. By removing the haulage bottleneck, we believe we can speed up underground operations substantially; and perhaps more important, we could make it feasible to develop a whole new generation of mining equipment that is inherently safer. What we wanted was a truly flexible, continuous haulage system with inherent safety advantages. Ideally the system had to meet three major requirements: First, the coal had to enter the transport system at the face, and remain in that same system all the way to the preparation plant. Second, the system had to be flexible and extensible so that it could- follow the mining machine as it advances and retracts. And, third, the system must be inherently safer than current haulage technology.

Jan 1, 1977

By L. Alan Weakly

The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement - fly ash mortar. Although the fully bonded bolt concept is not new as exemplified .by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1)(2) the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation's Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since December of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the grout-rebar system.

Jan 1, 1976

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant. able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). [ ] The most recent development, however, is the use of H2O2 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). [ ] Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: Hydrogen peroxide must be diluted before it is added to the pulp. The dosage of H2O, must be properly regulated based on the oxygen level of the pulp. An important part of the continuous O, control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1990

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By Timothy J. Matthews, Ted Klemetti, Timothy J. Batchler, Daniel J. McElhinney

Unplanned tailgate collapses and difficult mining conditions in U.S. longwalls have necessitated the use of innovative tailgate support systems. Severe ground movement induced by longwall loading has caused operators to utilize secondary support systems that can match yield and strength requirements with expected ground reactions. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. A full understanding of the impact of these performance characteristics is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. Optimization of roof support applications helps to ensure the protection of mine workers by preventing roof falls due to inadequate support design. The load capacity and stiffness characteristics of a 27-in.-diameter pumpable support system was evaluated using the National Institute of Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS). Previously, tests to evaluate the performance characteristics were performed on a single pumpable support. The goal of this new research is to evaluate the performance characteristic effects of the pumpable support system and compare it to an individual pumpable test examination. This research of a pumpable support system configuration simulates the current installation practices in U.S. coal mines.

Jul 1, 2023

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By Jess W. Smith

The carbonaceous Monkemeyer sandstone member of the Creede Formation on Bachelor Mountain hosts alteration and mineralization which contrasts with other silver deposits of the Amethyst system. More than 20 million ounces of silver are contained in disseminated mineralization in the volcaniclastic conglomerates and sandstones. Hydrothermal fluids entered the Creede Formation directly from the Amethyst fault system and mixed with flowing meteoric ground waters trapped beneath the Monkemeyer sandstone. Portions of the basal rocks of the Creede Formation were argillically altered by more dense acidic fluids generated by boiling. The carbonaceous base of the Monkemeyer and much of the conglomerates below were mineralized and well silicified. Deposition of the mineralization resulted from two processes: (1) reduction by carbon in the Monkemeyer, and (2) fluid mixing in the conglomerates. Monkemeyer mineralization is confined to the carbonaceous basal material and silver content is relatively consistent. Silver is contained in acanthite which is commonly associated with traces of galena, chalcocite, covellite and sphalerite. Fluid mixing and mineral deposition in the poorly sorted conglomerates was controlled by the highly variable porosity and permeability. Anomalous silver contents are dispersed throughout a large volume of conglomerates but zones of higher silver content reflect the crude layering of the conglomerates. Acanthite is finely disseminated in pore spaces and partly replaces some detrital magnetite. other metallic minerals are rare in the main zone of mineralization.

Jan 1, 2013

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

By H. Sevim

A new method of designing haulage systems, consisting of belt conveyors and hoists for underground mines is discussed in this paper. Efficient and economic design of such systems will prevent operational bottlenecks and provide savings. The developed model uses a heuristic algorithm to optimize the design parameters and to select the proper equipment specifications. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate belt conveyor networks of any configuration and hoisting systems that can be either drum or friction hoists for single or multiple-level operations. The model also has the option to internally determine the required capacities of the bunker(s) and shaft- bottom bin. The objective of the optimization process is to minimize the "expected cost per ton of ore hauled" from the working faces to the surface. A numerical example is included to illustrate the capabilities of the model.

Jan 1, 1987

By Ching Wu, David A. Sutter, Peter Frobenius

The MUNI Metro Turnback (MMT) Project includes a 256 m (840 ft) twin tunnel section, which connects to the Embarcadero Station, and runs under Market Street in San Francisco. The tunnels go through a mixed face condition of fill at top and Bay Mud at bottom, and a significant number of buried timber piles. This paper presents the selection of tunneling equipment, excavation methods, excavation support and chemical grouting; specification of timber pile cutting methods; and steel lining analysis and design. This paper also reports on the initial phase of the tunnel construction.

Jan 1, 1995