Search Documents

By M. S. Klima

Proper analysis of washability data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Jan 1, 1997

By Jeffrey M. Listak, Gregory J. Chekan

The U.S. Bureau of Mines, in an effort to improve coal conservation and utilization is currently investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When longwalling coalbeds in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau's MULSIM/NL model was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), which is an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. The attributes of both the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam (MS) factor to estimate the stress on the lower mine gate road pillars when superpositioning is practiced. Numerical analysis shows that the MS factor is dependent upon the interburden thickness and pillar width and is presented in a series of graphs relating these two parameters. Several examples are included to illustrate the use of the MS factor for estimating lower mine pillar stress and resulting stability factors.

Jan 1, 1992

By Jerry M. Whiting, Landy A. Stinnett

The subject of this paper is broad and complex. Secondly, it is near and dear to the authors' hearts. Therefore, it doesn't seem possible to deal with every aspect of it in less space than a good size textbook. Also, if we dealt with all of the basics of feasibility studies and report preparation, we would cover a lot of material available in the literature, and would have to minimize our editorial comments. In view of these limiting realities, we have chosen to discuss selected facets of the subject, and to provide several comments which stem from our personal experiences during the past 20 years. "Think Ahead" hen someone is undergoing training to command a large ship, the following short phrase is engraved in his memory: "Think Ahead." The reason is simple enough. A battleship, aircraft carrier or oil tanker cannot change directions quickly, and if one waits to a what the other ship is going to do, there may be twisted metal and bodies scattered all over the ocean floor. The commanding officer has to use radar, forward rind aft lookouts, experience, common sense, intuition, weather forecasts, and everything else available to him to avoid trouble. Remember the USS Stark, and the fate of its captain? The fact the Stark was hit by a "friendly" missile didn't lessen the damage. How about running into a mine? Is it an excuse that no one thought about the possibility of a minefield ahead of the ship? The point is, relative to feasibility studies, that its prospective authors, and especially the commander of the efforts required to create it, must "think ahead" from the moment of their association with 4 mining activity. They must

Jan 1, 1987

By Flavio Moreira Ferreira

In mining industry, one of the simplest methods to smooth the standard deviation of a given ore controlled property is to build longitudinal blending piles. The effect of homogeneization is obtained due to the fact that an entire cross-section of the pile is reclaimed at each time. The variance of the pile output is the sum of the internal cross-section slice variance plus the reclaimed slice variance. While the first term is a tipical short-term parameter and is absorbed by the process, the second one may be or may not be absorbed. The goal of designing blending piles is to minimize the reclaimed slice variance. Conditional Simulation as described in this paper, is an alternative method to do it. It is devised to design longitudinal blending piles, taking into consideration economical, geometrical and statistical parameters of the ore to be blended, in order to estimate the resulting effect. It presents advantages in relation to other methods for its adaptability and flexibility in simulating pile performances.

Jan 1, 1992

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By K. P. Unrug, E. Thompson, S. Nandy

The method of coal pillar design involves primarily two aspects: the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. As of now, the presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most often composed of multiple layers of coal, partings, and bone in various configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple uniaxial compressive strength tests performed on coal samples from the Coalburg and Warfield seams from eastern Kentucky was undertaken. Analysis of the results led to the conclusion that for pillar dimension calculations, both the weighted mean of the seam strength and the strength of the weakest stratum should be considered, rather than the relatively vague aspect of coal strength. The design of pillar dimensions based on the aforemen¬tioned criteria should assure a more realistic design performance.

Jan 1, 1987

By Jay Parrish

Appalachian kimberlites appear to be spatially distributed along two structure parallel trends running from Tennessee to New York. It is hypothesized that the kimberlites were emplaced at the intersection of structure parallel basement faults and cross- structural lineaments. The latter are expressed in potential field and remotely sensed data. The western trend follows the Rome Trough from eastern Kentucky to south central New York. The eastern trend parallels the edge of the Ridge and Valley in Virginia and Maryland.

Jan 1, 1984

By N. K. Riddle

In many mines, it is typical to stockpile material for milling based either on analyses from exploration and blasthole drilling, or on the observation and judgment of experienced personnel. New analytical instruments make it possible to perform multiple, rapid analyses of as-mined samples at or near the mining face, so that sorting into stockpiles can be much more accurate. Using data and operating practices from a phosphate mine, a model was developed to simulate the function of analytical instruments in ore-grade control and ore stockpiling. With this model, it is possible to determine the recommended sampling points and sample frequency to obtain the desired confidence limits on the stockpile analyses.

Jan 1, 2003

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for the removal of copper from heap-leach solutions without mobile organic phases are a current mining industry need. To satisfy this need, a selective, high-capacity, durable solid material is required. The Idaho National Engineering and Environmental Laboratory (INEEL) developed a set of materials based on current solvent-extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, the author's strategy anchors the chelators to a nonpolymeric solid substrate through the use of a custom-designed linker molecule. The fundamental synthetic routes to these materials have already been established, and attachment to the solid surfaces have been achieved in an efficient manner. The author's continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper-capturing capabilities.

Jan 1, 2003

The Mine Safety and Health Administration (MSHA) has conducted studies to evaluate dust control technologies on deep cut continuous mining sections. These surveys have been conducted in different mines using various mining methods, face ventilation systems and dust control systems. The surveys typically consist of respirable dust sampling combined with a time study of mining activities. Measurements of dust control and operational parameters are also made. Critical elements identified for controlling respirable dust in deep cut mining systems include controlling intake dust, dust collector capacity, face ventilation quantities and velocities, positioning of workers, work practices and selection of equipment. This paper discusses how the dust surveys are conducted in deep cut mining sections and how these surveys are used to identify specific dust generating sources.

Jan 1, 1999

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By Brian H. Zelenko, Patricia M. Perry

INTRODUCTION The environmental requirements of the next section of Washington, D.C. METRO subway tunnels present unique challenges to the Contractor. The 14th Street Tunnels contract includes twin 975 m (3200 linear ft) soft ground tunnels. A stringent environmental soil and groundwater monitoring and free product recovery program was specified by the owner. A project-wide dewatering program hinges on satisfactory completion of the environmental requirements. Implementation of the Contractor's environmental program is discussed, including the pros and cons of the program, as they relate to progress of the project. Environmental issues on tunneling projects have become an important part of the urban tunnel construction process. Delays associated with environmental issues can have a major cost impact on tunneling projects. This paper will discuss the first of five Washington Metropolitan Area Transit Authority (WMATA) tunnel and station contracts awarded in 1994. These contracts are part of WMATA's Fast Track Plan to complete the original 166 km (103 mile) system by 2001. As such, stringent environmental requirements have been specified as a part of these contracts to limit delays associated with local regulators in order that the tunnels may be constructed on schedule.

Jan 1, 1995

By Kim Lapakko

As part of a project funded by the US EPA, through the Western Governors' Association, the recent literature on the prediction of acid drainage from metal mine wastes was reviewed. Static tests such as Acid Base Accounting, Modified Acid Base Accounting, B. C. Research Initial Test, and APP:S Test attempt to quantify the total capacities for a mine waste to produce and consume acid. In kinetic tests (e.g. humidity cells, soxhlet extraction, elevated temperature oxidation, column tests, batch reactor tests, B. C. Research Confirmation Test) mine waste samples are subjected to oxidation and the resultant drainage pH is assumed to reflect that of mine wastes dissolving in the field. This paper summarizes information presented in the recent literature on static tests.

Jan 1, 1992

By M. Plesha, A. Zubelewicz, K. Connor, T. B. Belytschko, O&apos

INTRODUCTION The Northwestern University Rigid Block Model (NURBM) has been extended to explicitly model dilatant behavior of rock joints. By incorporating dilatancy, the resistance to shear displacement and slip, which previously was limited to simple Coulomb friction, along edge-to- edge contacts is now provided by contact roughness as well as frictional resistance. The explicit formulation is based on concepts presented by Plesha (1985) in which a plasticity-based phenomenological approach was used to model dilatant joint behavior. This approach has been modified to allow for joint closure upon reversal of shear deformation. After presenting a brief description of the new joint constitutive relationship, model behavior will be illustrated with two examples. The first involves a simple two-block model to simulate a cyclic direct shear test of a single joint. The second example involves simulation of a large cavern in a moderately jointed rock mass subjected to cyclic excitation. It will be shown that in- creasing joint roughness increases cavern stability by interlocking of adjacent blocks. JOINT CONSTITUTIVE RELATIONSHIP Within NURBM adjacent two-dimensional rigid blocks interact along their common edge-to-edge contact with contact forces transmitted at the contact midpoint. The contact constitutive relationship was originally restricted to a Coulomb friction yield criterion with no tensile stresses permitted along the smooth contact surfaces. The local coordinate system for any contact is described as shown in Figure 1 with the elastic stresses and displacements related by the linear- elastic constitutive law: [ ] The contact microstructure has been modeled as Patton-type saw-tooth surfaces such as shown in Figure 2. Sliding can be active along the right asperity with angle aR and length lR or along the left asperity with angle a and length lL. In general, aR and aL will difkr as will lR and lL but for purposes of this paper it has been assumed that these angles and lengths are identical. By a simple transformation, the microscopic asperity stresses can be expressed in terms of the macroscopic contact stresses [ ] If Coulomb friction is assumed along the asperity surfaces, the plastic slip condition will be [ ] where µ is the friction coefficient with the convention that compressive stress is negative. When F is negative, the behavior is elastic and when F is zero, slip can ensure. When plastic slipping does occur, it is assumed that the relative tangential and normal displacements between the two contacting rigid blocks are additively composed of recoverable elastic parts and nonrecoverale plastic parts, [ ]

Jan 1, 1986

By L. Spiers

Motorized Conveyor Pulleys contain all the traditional conveyor belt drive components inside the pulley. Light duty airport check in, grocery stores and food processing conveyors; requiring compactness, elimination of guarding and component containment have been using them for years. Portable Aggregate Processing Equipment require these features but with higher belt pulls and severe duty beyond the capacity of traditional components in a limited space. New materials, design technologies and automation; converging with safety issues, higher energy and operating costs; have created a pressing need. The challenge is to integrate new technologies and traditional components into a reliable, compact, conveyor belt drive system.

Jan 1, 2003

By M. Karmis

"The process of coal mining, as indeed of the mining of any stratified mineral, is inevitably followed by some degree of sinking of the superjacent strata and consequently of the surface." Royal Commission on Mining Subsidence, Second and Final Report, London, 1927. INTRODUCTION The above statement was used to describe mining subsidence in the classic report of the "Royal Commission on Mining Subsidence," published in 1927. In fact, this phenomenon has been recognized in Britain since the early fifteenth century, as revealed from court records of disputes and litigations related to property damage above mine workings (Shadbolt, 1978). The first attempts to investigate and analyze the mechanisms associated with mining subsidence, however, date back to the 1800's and were pursued by Belgian Engineers. This research effort was initiated as a result of the widespread movements and subsequent structural damage suffered by the City of Liege in the 1820's. The most notable achievement of the Belgian school of that era was he publication of Gonot's treatise "Loie de la Normal" in 1871 (Gongt, 1871).

Jan 1, 1982

It doesn't take any special acumen to note that US engineering and construction firms are busier than ever with mining projects in this mineral conscious world. This special issue of Mining Engineering takes a look at E&C companies-their expanding role, their special capabilities, and their challenges and problems. ME sent a questionnaire to a representative sample of E&C firms. Information was sought about officers, ownership, and amount of business. ME also asked about types of projects and commodities dealt in as well as market distribution and forms of payment. The accomnanying charts show how the 17 responding E&C firms answered these and other questions. Other ME survey questions, and a review of company literature, yielded information about financing techniques and special challenges for E&C firms. Insights were gained concerning government impacts, customer-generated problems, and promising areas for development-including synfuels-in the minerals industry. These areas are discussed later in this article. Accompanying articles in the special issue discuss the E&C company's role in mining projects, research and development in E&C firms, one approach to contract work used by an E&C firm, and an E&C project case study.

Jan 10, 1980

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996

By F. F. Aplan

Rather than reiterate what is well known about the flotation of the non-sulfide minerals, emphasis has been placed on those separations which are not so effective. These difficult separations are largely connected with problems of selectivity in the flotation of the base metal oxides, the other slightly soluble minerals, the insoluble oxides and the naturally floatable minerals. The paper discusses possible methods of improving selectivity between similar species and of improving selectivity against the gangue minerals.

Jan 1, 1994

By H. Reginald Hardy, Maochen Ge

Data analysis is one of the most important steps required for the successful application of the acoustic emission/ microseismic (AE/MS) technique. A dedicated computer software package to analyze acoustic emission/ microseismic data associated with field applications in the geotechnical area has been developed recently at Penn State University. This paper addresses the major features and applications of this computer software package.

Jan 1, 1986