Search Documents

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992

By Robert Semrad, J. Colin Anderson

INTRODUCTION Sulphur is a mineral which accounts for 0.05% of the earth's crust and may be found either in its elemental state or as a compound. References to sulphur production and consumption are found in early antiquity and international trade of sulphur from volcanic deposits in Sicily began in the 1880's. The supply of sulphur consists of two components: the first is production, and the second is inventory. HISTORICAL SUPPLY Production World sulphur production in 1984 was approximately 53.5 million metric tons, compared to the 1970 level of 42 million metric tons. Of this 11.5 million metric tons production increase, brimstone accounted for close to 90%. Production distribution in 1984 was 62% brimstone, 21% pyrites and 17% other forms, while in 1970 it was 55%, 28% and 17%, respectively. Brimstone Production is derived either from mining operations (Frasch, underground melting and native refined) or as a by-product from hydrocarbons. World production in 1984 exceeded 33 million metric tons, up approximately 10 million metric tons from the 1970 level. This increase was uniformly distributed throughout the world as shown in Table A.

Jan 1, 1986

By G. T. Adel

During the past decade, researchers at Virginia Polytechnic Institute and State University have worked to develop a novel flotation process for treating very fine particles. This process, which is now commonly known as [microbubble column flotation] (MCF), has been shown to be very effective in a number of applications related to fine coal processing. These applications include the retrofit of existing preparation plant circuits and the recovery of additional coal fines from refuse streams. In addition, work conducted under the sponsorship of the United States Department of Energy indicates that the MCF process is capable of producing superclean and ultraclean coals from many eastern U.S. coals. This paper describes some of the basic problems associated with fine particle flotation and the design and operational features of the MCF process used to minimize these problems. Also presented are the results of ongoing pilot- and field-testing programs.

Jan 1, 1989

By Martial P. Corriveau

The preparation of coal is essentially the same for export as it is for the domestic market. The big difference, I would say, is that, while coal for certain domestic uses (utilities, for instance) need not always be of the highest quality, as long as it is uniform, the buyer of coal for export invariably demands a well-prepared, top-quality product. And he is willing to pay for it, as long as he knows what he is buying. This is where quality control enters the picture. The day is long past since the export market was the dumping ground for coals which could not be sold on the domestic market. Today, the export buyer wants American coals not so much for a price but for the necessity of blending the American coals with foreign coals to achieve the desired chemical and/or physical characteristics, To blend intelligently, he must know in detail what are the qualities of the coals to be blended. Sampling and chemical analysis facilities at the piers provide the information on the coals exported, These facilities are maintained for the export buyer by independent laboratories; however, in one instance, the buyer operates his own laboratory. With very few exceptions, and Clinchfield?s Moss No. 3 mid-volatile coal is one, cargoes shipped overseas are loaded as blends of two or more coals. Up to now, foreign requirements have not been too clearly defined; therefore, shippers must be prepared to blend mixtures of the desired combination. Successful blending requires an accurate knowledge of the coals shipped. And this makes it necessary for the coal producer to maintain his own control laboratory.

Jan 1, 1959

By Michael J. Howes

The nature of business in a free enterprise system is to maximise the return on an investment i.e. to maximise the wealth of the shareholders. This is normally achieved within constraints dictated by many agencies, one of which is the health and welfare of the employees. In the mining industry considerable effort has been expended in improvements in this field, however, the major problem still confronting the practicing ventilation or environmental engineer is the determination of what standards he should design for, which satisfy both the economic and health requirement s. Normally the basic health requirements are satisfied by the minimum standards defined in regulations and codes of practice. These are, however, based on an acceptance of a certain risk or lower production potential. A prime function of the ventilation engineer is therefore to financially justify and implement improvements to both standards and systems. The main purpose of this paper is to examine the basis and techniques of providing this financial justification. Changes in existing methods to achieve the same standards but at lower costs are also covered.

Jan 1, 1980

By James A. Jones

The Doe Run Co. emerged from the depressed lead market of the mid-1980s as North America's leading lead producer. Doe Run was lean and mean but quickly recognized that technology had advanced while the company was held to the belt tightening slump. With the 1990s approaching, Doe Run moved quickly to update its technology and control equipment to ensure its position as an industry leader. Doe Run was formed in 1986 when Fluor Corp. and Homestake Mining Co. combined their lead-zinc-copper assets in Missouri to form a joint venture. Doe Run is now owned by Fluor Corp. A rich history of mining, milling and smelting started in Missouri in 1862 when the St. Joseph Lead Co. was founded. Subsequent acquisitions led to the formation of St. Joe Minerals, which was later purchased by Fluor Corp. Six mines, four concentrators and two smelters are presently being operated, and a secondary lead smelter was recently commissioned. The Viburnum, Buick and Fletcher operations are lead, zinc and copper flotation concentrators, while the Brushy Creek plant is set up to process high copper-low lead ores. This article looks primarily at the process control installation at the Fletcher concentrator.

Jan 1, 1991

By Harry Teicher

The subject of Specialty Silica Products could encompass a broad range of materials, some of which would be familiar to members of the Society of Mining Engineers. With the concurrence of your chairman, I have chosen to limit my remarks to synthetic materials, not including such siliceous materials as diatomaceous earth, asbestos, quartz and clays. For purposes of discussion, I have classified Specialty Silica Products into two groups -- powders and liquids -- which I will discuss in that order and which are categorized in Figure 1. The synthetic silica powders are amorphous to x-rays and are manufactured by various processes resulting in products of a wide range of physical and chemical properties, as well as functional performance and applications. Applications or functional properties are generally dependent upon such physical properties as micron-sized particles exhibiting large surface areas per unit weight and low apparent bulk density. Their presence in various systems modify surface properties. As summarized in Figure 2, they act as viscosity modifiers, flow conditioning agents, anti-slip agents, anti-blocking agents, flatting agents in surface coatings, reinforcing agents in polymers such as silicone rubber and numerous other applications. Although the various types of silicas exhibit various levels of functional performance in these end uses, they are not usually equally effective as direct replacements and I will briefly discuss the various types of materials.

Jan 1, 1974

By K. Biswas, S. J. Jung

Health and safety of workers in mineral industry in the U.S. is still a vey important issue as Mining along with Agriculture, Forestry and Fishing and Construction industries have contributed most of the fatal occupational injuries ill between 1980 - 1995 (Worker Health Chartbook, 2000). Health and safety issues, especially for the mining or related excavation industries, arise either from exposures of the human workers to the contaminants liberated or generated by mining operations that have adverse effects on human health (for example coal dust etc.) or from the exposures of the human workers to hazardous working environment that constitutes mining operations (for example blasting etc.). One of the biggest challenges is to understand the combinatorial effect of numerous work-condition (e.g. exposure to dust) and human-factor (e.g. smoking habit) variables on a health or safety-condition variable (e.g. incidence rate of a disease). This paper uses an example dataset on Coal miners' cough problem to illustrate the applicability of Generalized Linear Modeling (GLM) in understanding the relation between cough and other response variables, such as, age, height, smoking habits, time of underground exposure etc.

Jan 1, 2002

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By K. T. Mau

Hawaii is located approximately 2,500 miles from the mainland, but has basic needs for its thriving developing community. Cement is one of these needs Cement production in Hawaii is not without handicaps. The necessary raw materials are practically non-existent except for limestone. Even at that, the available limestone is marine in origin, coralline in nature and amorphous in characteristics - unlike calcite which is normally the calcium carbonate source for cement manufacture. There is no clay or shale for the argillaceous portion of cement raw mix. Hawaii being volcanic in origin is too young geologically for clays and shales to evolve and whatever there is, most likely is washed into the ocean.

Jan 1, 1982

By A. B. Seal, C. J. Bise

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during the mid-1970s and mid-1990s consistently show that hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When the U.S. Mine Safety and Health Administration's new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to reevaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Pennsylvania State University research project now being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2003

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992

By R. M. Carland, F. F. Aplan

The ion-exchange capabilities of natural zeolites from the western United States, representing the species chabazite, clinoptilolite, erionite and mordenite, have been studied because of their potential use in environmental remediation and in hydrometallurgical processes. These raw zeolite samples were found to contain Na+, K+, Ca+2 and Mg+2 as exchangeable cations, and all of these, with the exception of Na+, were found to seriously interfere with the exchange of Cu+2 from solution. Placing these zeolites in the Na+ form was found to increase their cation-exchange capacity, often massively. In addition, the elution of Cu+2 from the Na+ pre-exchanged zeolite is greatly facilitated when the deleterious K+, Ca+2 and Mg+2 have been largely expelled. The relative influence of these deleterious ions on the uptake and elution of Cu+2 was determined.

Jan 1, 1996

By R. B. Taylor

The Esmeralda mine is located about three miles west of the town of Parral, in the State of Chihuahua, Northern Mexico, and about 400 miles south of El Paso, Texas. The area is serviced by the Interamerican Highway and a branch line of the National Railways of Mexico. The Parral district is quite typical of the semidesert of Northern Mexico, lying near the western margin of the Chihuahua basin and range province known in Mexico as the ?Mesa Central? In the immediate mine area, low rounded hills and rolling plans slope toward the Parral River. Surface elevation at the mine is 5,800 feet. The Esmeralda vein outcrops strongly, but was too low grade to be of interest to the Spaniards, The first claims were staked in 1897 and limited exploration work to a depth of 550 feet was carried out prior to 1912, at which time work was suspended. The Eagle-Picher Company acquired the property in 1944 and by surface diamond drilling outlined an orebody to a depth of 800 feet, Minas de Iguala, S. A, de C.V., one of Eagle-Picher?s totally owned subsidiary companies in Mexico, then unwatered the old workings, developed the mine, installed a modern differential flotation plant and started production lage in 1948. To the present, more than two and ahalf million tons of ore have been mined and milled producing lead and zinc concentrates.

Jan 1, 1958

By Alfred F. Savage

The Oglebay Norton Company has traditionally been a supplier of metallurgical grade fluorspar gravel to the American steel industry and, in the early sixties, fluorspar pellets were entered into the market. The gravel has been imported from Mexico, the pellets were produced by the Minerva Company in southern Illinois. While the acceptance of the pellets by the industry was satisfactory, overall marketing considerations caused the Minerva Company to discontinue the pelletizing operations. Thus it was that Oglebay Norton came to the decision to revive earlier plans to produce fluorspar agglomerates. A survey of the market and related factors led into two basic conclusions: 1) Because of steel plant safety considerations, flat, pillow- shaped briquets were preferable to easily rolling, marble-like pellets. 2) Briquets competitive with gravel could be produced by cutting imported, low-duty, acid grade spar to metallurgical grade by limestone and binders. A plant was built in Brownsville, Texas, and started operations in early 1970.

Jan 1, 1975

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970

By Chas. F. Jackson

INTRODUCTION This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the US Bureau of Mines (USBM) and made possible through the cooperation of many mining companies in the US and foreign countries. The data presented have been obtained from papers previously published by the Bureau dealing with indi¬vidual mines, from the technical press, and from infor¬mation furnished by the mining companies. DEFINITIONS Top Slicing The term top slicing is commonly applied to that method of mining in which the ore is extracted by a series of timbered slices, beginning at the capping; the slice is caved, bringing down the capping to the floor of the slice; the succeeding lower slices are mined up to the overlying mat or gob, consisting of an accumulation of timber from the upper slices and broken capping, which follows the mining progressively downward (Fig. 1). The term has also come to be applied to the mining of ore bodies only one slice thick, by a series of tim¬bered slices one beside the other. The timbers are blasted out, bringing the capping down to the floor, suc¬ceeding slices being driven alongside those already caved (Fig. 2). In USBM classifications of mining methods, top slic¬ing has been placed under the heading caved stopes. The method differs fundamentally, however, from the cav¬ing methods of mining in which the breaking of the ore itself is accomplished by caving action induced by undercutting. In top slicing the ore is broken by the ordinary methods of drilling and blasting, and only the capping is broken up by caving. Main Levels or Haulage Levels Main or haulage levels are the main extraction levels on which the ore is hauled to the shaft. These levels and the shaft constitute the preliminary development of the mine.

Jan 1, 1982

By B. J. Arnold

A coal's size distribution clay content and moisture content can affect its handling behavior. But the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.'s (formerly EPRI's) Coal Quality Development Center (CQDC) and at Iowa State University (ISU) will answer these questions as part of a four year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of carious coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that while moisture content is the most important variable, the amount of -44 µm (-325 mesh) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1992

By K. Hanumantha Rao, K. S. E. Forssberg, A. Vidyadhar

Using pure albite and quartz minerals, the separation of albite from quartz using mixed cationic/anionic reagent schemes is assessed through Hallimond flotation, zeta potential and diffuse reflectance FTIR studies. The reagent schemes are tested in bench-scale flotation for the separation of albite from Greek Stefania feldspar ore. The single mineral flotation tests showed the feasibility of selective albite flotation from quartz at around pH 2 using a mixture of cationic diamine and anionic sulfonate collectors or a combined cationic-anionic collector of diamine-dioleate. In contrast to the selective flotation response of albite at pH 2, where albite is slightly negatively charged and quartz possess zero charge, the zeta potential and FTIR studies elucidate similar adsorption behavior of mixed collectors on both of the minerals. The infrared spectra not only showed the co-adsorption of anionic sulfonate or oleate with diamine on the surface but also showed that the diamine adsorption increases with the presence of anionic collector. The intrusion of anionic collector in between adjacent surface alkyl ammonium ions decreases electrostatic head-head repulsion, thereby increasing the diamine adsorption by increasing the hydrophobic tail-tail bonds. The discrepancy in the flotation and adsorption results at pH 2 is attributed to the coarse and fine size particles employed in these studies, respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding besides electrostatic interactions. The bench-scale flotation results indeed showed that selective albite flotation takes place only after desliming the feed material. An albite concentrate exceeding 10% (by weight) Na20 is produced from a material containing about 6.5% (by weight) Na20, where an albite product of more than 9% (by weight) Na20 is considered to be valuable. Key words: Flotation, Adsorption, Zeta-potential, FTIR

Jan 1, 2003