Search Documents

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By Daniel Gauthier, Patrick Sharrock, Cedric Verwilghen, Gilles Flamant, Ange Nzihou, Jocelyn Ramaroson

Clean processes are needed to dispose of many wastes. The incineration of 1 ton of municipal solid waste generates 6000 Nm3 of combustion gases contaminated with heavy metals and other pollutants. Gas scrubbing processes are required to clean incineration fumes in order not to transfer pollution to the atmosphere. We are investigating the use of Hydroxylapatite (Ca-HA) particles for use as sorbent for the removal of volatile heavy metals. We have carried out the synthesis of Ca-HA by two precipitation methods from solution and obtained solids with specific surface areas reaching more than 100 m2/g. Preliminary adsorption experiments were conducted in a horizontal furnace by mixing Ca-HA with 5% by weight of cadmium chloride in solid state. The mixture was heated to 600°C under air atmosphere during 6 hours. Chemical analysis of the solids confirmed that 85 % of the cadmium was retained in the solid phase. Such laboratory results showed that Ca-HA is capable of adsorbing cadmium chloride vapors, and pilot scale studies confirmed cadmium abatement in an industrial context.

Jan 1, 2008

By Claudio Toro, Alex Moyano, Jonkion Font, Carlos Caballero, Pedro Morales

"Codelco-Chile in the last decade has carried out industrially-oriented research as an alternative to the traditional batch-type converting process. In a first stage carried out preliminary evaluations in a rearranged Peirce Smith (PS) converter, and then an exploratory test in a “Convertidor Teniente” (Teniente converter, TC) for the Codelco-Chile Continuous Converting Process. However, the validation test for this process in the TC was delayed up to the second quarter of 2007 where the validation studies were done satisfactorily.Thus, the objective of this paper is to present the results of the campaign tests validating the Codelco-Chile Continuous Converting Process in the TC1 of the Codelco Norte smelter.The results of charging the solid or liquid matte or high grade matte (“white metal”) by Garrgun, or by mouth of the 22 m x 5 m TC1 are presented. Some features of the industrially validated process are discussed, and the pilot test results of the matte injection are also presented."

Jan 1, 2009

By J. Dille

Metallic cobalt exist in two allotropic forms : the hexagonal compact a which is stable at low temperature ( ( 420') and the cubic form 0 stable at higher temperature. This latest form is the only one which is ductile. During the electrode position of Co, in moderate acidic conditions, we noticed a code position of both a and B forms. The influence of several parameters on the B/a ratio in the deposit was investigated. High acidity and the presence of Fe increased its ratio; on the opposite, high temperature promote the a phase. No significant influence on the material were noticed. The differentiation of a and B forms of Co is rather difficult and the method of J. Scoyer was improved quite successfully.

Jan 1, 1988

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By G. Van Weert

The pellet reactor was developed approximately 20 years ago in the Netherlands for softening drinking water. Since then, some 35 plants have been built, ranging in capacity up to 8500 m3/h. Applications now also include removal of phosphates and fluorides and the production of metal carbonates and sulphides from waste streams. The pellet reactor consists of a fluidized bed, wherein the process solution is thoroughly mixed with the precipitation reagent at special inlet nozzles to give over-saturation of the compound to be precipitated. In water softening applications, the compound is CaCO,. In the case of nickel or other metal waste streams, Na2CO3 solution is added in sufficient amounts to precipitate metal (hydroxy) carbonate on the fluid bed particles. These grow typically to dense spheroids, which are removed when they reach 0.8 to 1.0 mm diameter. These spheroids are easily dewatered, free flowing and low dusting. The latter property is becoming an attractive advantage in connection with new plant hygiene regulations. The operation of a 60 cm diameter pellet reactor on nickel containing plating waste is described and the properties of the produced nickel carbonate spheroids are discussed.

Jan 1, 1993

By E. Salinas-Rodriguez, J. Hernández-Ávila, E. O. Ávila-Dávila, A. Romero-Serrano, M. Perez-Labra, G. Juárez-López

"Single phase rubidium jarosite was synthesized by precipitation from aqueous solution. X-ray diffraction and SEM-EDS analyses showed that the synthetic rubidium jarosite formed in subspherical particles with an average particle size of about 35 µm. The chemical analysis showed an approximate composition of Rbo9432Fe3(SO4)2 1245(OH)6. The decomposition behaviour of the jarosite in terms of solution pH was thermodynamically modeled using FACTSage by constructing the potential-pH diagram at 298.15 K. The E-pH diagram showed that the decomposition of jarosite leads to goethite (FeOOH) together with Rb+ and SO42- ions. The experimental decomposition of the Rb-jarosite was carried out in alkaline solutions with five different Ca(OH)2 concentrations. The decomposition process showed an ""induction period"" followed y a progressive conversion period where the Rb+ and SO42- ions formed in the aqueous solution. In contrast, calcium was incorporated in the solid residue and iron was transformed into amorphous ferrihydrite. The kinetic analysis showed that this process can be represented by the unreacted-core chemically controlled model. The reaction order with respect to Ca(OH)2 is 0.4342 and the calculated activation energy is 98.70 kJ mol-1. IntroductionJarosite type compounds are hydrous sulfate minerals containing alkalis and ferric ions, MFe3(SO4)2(OH)6, where M can be H3O+· Na+, K+, Rb+, Ag+, NH4 +, Tl+, ½ Pb2+ or ½ Hg2+. Jarosite-type compounds were formed by the natural ""in situ"" oxidation of pyritic ores leading to the replacement of the original iron sulfides and iron oxides (Dutrizac and Kaiman) [1]. The great interest in jarosites is due to its ability to eliminate or diminish the iron concentration of the acid leach solutions produced in the hydrometallurgical zinc process, with relatively low losses of divalent metals such as Zn2+, Cd2+, Cu2+ or Co . However, the losses of the metal values demand a careful study of the conditions under which the jarosite compounds are formed together with their chemical properties."

Jan 1, 2012

By B. Thompson

"1. AbstractMagnesium alloys have been successfully recycled for decades and have won acceptance for use by die casters and most of the automotive industry. As the supply chain for magnesium and magnesium alloys continues to change, due to the consolidation of producers, it is essential that quality control methods be closely examined with each new supplier added. An examination of the various process steps that are needed to assure quality in the final product will be discussed thus giving a basis for the auditing of new magnesium suppliers.2. IntroductionMagnesium recycling in the past has been somewhat limited due to its use more as an alloying agent for aluminum based alloys and as a desulfurization agent in iron and steel than in more readily recycled structural products. Recycling efforts continue to improve as more production is finding its way into automotive structural components, hand tools, and a variety of computer and cellular telephone applications.With the closure of several large North American primary magnesium production facilities over the past decade we have only recently witnessed a tightness in supply that is driving magnesium prices significantly higher, nearly doubling the price in the last year alone. The rapid escalation in pricing will provide additional economic incentives to fully utilize recycling for the recovery of an even greater percentage of both old and new sources of magnesium scrap. Political pressure continues to intensify towards the secondary recovery of any and all recoverable resources of which magnesium recycling readily applies.Economics will also likely drive the development of new sources of magnesium production, both from primary and secondary production. As new sources of magnesium are offered to the marketplace the potential for product quality issues may increase. When considering any new raw material supplier a decision must be made as to the impact of defective material on the intermediate or finished product. Quality defects in magnesium ingot can result in a variety of appearance, corrosion, and even adverse structural effects in the finished product. The potential severity of the impact of defective raw materials on the finished product will determine and often justify a close look at any new supplier. An on-site audit of a new supplier of a critical raw material is often justified to ensure that an adequate quality assurance system is in place. We will now look at a number of key production points that should be examined during an on-site audit that have can have an impact on the overall quality of the finished product."

Jan 1, 2008

By Du Sichen, S. Seetharaman, Wei Liu

"The viscosities of two-phase mixtures are of great importance in the modelling of the fluid flow in metallurgical processes. For example, in steel making and refining, the intimate mixing of metal droplets in the slag phase requires a consideration of the effective viscosities for the mixture. The present work was aimed at an understanding the phenomena underlying the viscous flow in a two-phase mixture with widely differing viscosities.Emulsions of silicone oils of known viscosities (345mPa.S and 1010mPa.S at 293K) with small amounts of water evenly distributed in the same were prepared by subjecting the mixture to uniform stirring using a magnetic stirrer. The viscosities of these emulsions were measured at constant temperature by rotating cylinder method using Brookfield Digital Rheometer. The uniformity of the preparation of the emulsions was confirmed by the reproducibility of the results. Th7 measured viscosities were generally found to be independent of the torque under the experimental conditions so that the two-phase mixture could be considered as a Newtonian liquid. The variation of viscosities with temperature and the effect of addition of a surface-active substance were also studied in this work.The measured viscosities were found to be· higher than those of both pure water and silicone oil. The experimental viscosities were found to increase with increasing concentration of water. The influence of surface tension on the viscosities was examined by adding surfaceactive agent to the mixtures. The result is discussed and compared with theoretical models developed by Einstein, Taylor and Oldroyd."

Jan 1, 2000

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By Jitka Jandová

In this study, hydrometallurgical processing of waste ZnO flue dust arising during zinc removal from galvanized low-alloy steel sheets was investigated on a laboratory-scale to obtain electrolytic zinc. The flue dust was separated from flue gases, generated during heating waste galvanized steel sheets in an electric furnace under air atmosphere at temperatures of about 1000oC. The dust, comprising tetragonal ZnO and insignificant amounts of SiO2, was contaminated by Fe, Mn, Pb, Al, Mg, Pb, Cu and Ca. The dust was leached in 0.5 and 1.0M H2SO4 and/or in 20 and 30% NaOH at different temperatures and different liquid-to-solid ratios to determine the optimum conditions leading to the highest possible selectivity of leaching and efficiency of Zn extraction in minimum time. The subsequent electrowinning process was performed with refined zinc sulphate leach liquors and/or with untreated zinc caustic solutions. Zinc sulphate leach liquors were purified using a combination of a hydrolytic pH-controlled precipitation, cementation and carbon refining. Effects of operational variables on Zn electrowinning have been studied for both sulphate and caustic electrolytes. The conventional plate-plate electrowinning cell has been explored in this study. Comparison of results obtained for both zinc electrowinning from acid sulphate and alkaline solutions is presented contribution.

Jan 1, 2003

By Ephraim Jeya Kumari

The demand for the titanium dioxide pigments and the shortage of higher-grade titaniferous ores with low radioactivity and zircon sands worldwide has encouraged the development of new techniques for the beneficiation of lesser grade titaniferous ores. The inferior quality ores are invariably richer in radio-active and lanthanide oxides, which severely interfere with the fluidized bed chlorination reaction (FBCR), in which ultra-high purity titanium tetrachloride is distilled off for pigment manufacture. However the present beneficiation techniques require high quality ilmenite ores and are not suitable for upgrading lower grade ilmenite ores which do posses trace metals in the form of lanthanides and actinides as Al-phosphates and zirconium silicates, respectively. The presence of mineral hosts, zircon sand and monazite in ilmenite and anatase also increase in chlorine gas consumption in the FBCR and contribute to a larger volume of hazardous waste production, which must be neutralised at a significant cost before being disposed off safely. In view of the problems described for lanthanide (Ce, Nd etc) and actinide (Th, U) trace impurities in titaniferous ores, an alternative route, which is flexible and more accommodating for processing difficult ores, is discussed. In the new process, which may be used for richer grades of ores too, the ore is roasted in air with sodium carbonate below 950°C to promote the formation of water-soluble sodium ferrite and insoluble sodium titanate phases. In this investigation, the high-temperature roasting process and the ensuing hydrometallurgical leaching steps have been analysed in the context of selective separation of lanthanide and actinide minerals from the main titaniferous mineral structures. Evidences for the selective separation are presented based on the chemical (XRD, XRF, AA) and microstructural analysis (SEM, EDX, EPMA) of roasted mass and the leached product. The efficiency of selective separation is also reported based on the chemicals analysis and the particle size of the materials derived after leaching. The paper highlights the various thermodynamic aspects of reaction equilibrium in the Fe-Ti-O-Na system, and the effect of Eh-pH diagram in the determination of pH required for the better control of the removal of iron and sodium. Two different types of Ti ores, namely ilmenite and anatase, their crystal structure and the phase transformation will also be explained on the basis of wet chemical analysis, XRF, XRD, EPMA and SEM-EDX studies. The method developed examines the technological feasibility of the selective separation process.

Jan 1, 2006

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By Qian Xu, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Shuhua Geng, Hongwei Cheng

Herein we report an electrochemical route from oxides (SiO2, TiO2)/sulfide (MoS2)/carbon mixture precursors to Mo-Si-Ti-C composites in molten salt. The electrochemical process was carried out in molten CaCl2 at 800 °C with a potential of 3.1 V, and a graphite-based anode was used in the electroreduction process. The reaction mechanism and the influences of the stoichiometry of the initial mixture precursor on the morphology and phase composition of the final products were investigated. It has been found that Mo5Si3/MoSi2/Mo3Si/Mo, Mo5Si3/MoSi2/Mo2C/SiC, and Mo5Si3/Mo2C/Ti3SiC2/TiC/Mo composites can be electrosynthesized directly from their oxides/sulfide/carbon mixture. The preliminary experimental results suggest that the electroreduction process can be used for the controllable electrolytic production of alloys/carbide-containing composites from oxides/sulfides/carbon precursors.

Jan 1, 2016

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Wander. L. Vasconcelos, Virgínia. S. T. Ciminelli, Angela. M. F. Guimarães

"The present work was aimed at synthesizing nanostructured hybrid materials derived from the functionalization of smectite clays with ligands containing thiol (-SH) groups for application in cadmium adsorption processes. An in nature Brazilian bentonite was investigated. The modification route was based on the grafting reaction between hydroxyl groups present on clay surface and the hydrolyzable alkoxy group of the (3-mercaptopropyl)trimethoxysilane in dry toluene under reflux. The present work showed that the proposed modification route was effective for the grafting of the thiol groups in the clay structure. The thiol-functionalized bentonite samples showed average binding capacities 160% higher with respect to Cd2+ to those obtained with the ungrafted material. These results support a mechanism of adsorption involving primarily ion complexation by the thiol groups (specific) instead of cation exchange (unspecific). The proposed modification processes are suggested for the preparation of novel adsorbent materials with controlled selectivity and specificity and therefore with good potential for separation and pre-concentration purposes.IntroductionMany efforts have recently been devoted to the design and preparation of inorganic-organic nanomaterials because of their potential application in novel functional materials. The intercalation of organic species within the spaces between interlayers of inorganic layered crystals provides nanostructures consisting of alternating layers of inorganic and organic compound. The intercalation reactions occur by insertion of mobile guest species (neutral, molecules, or ions) into the accessible crystallographic-defined vacant sites located between the layers (interlayer spacing) of the layered host structure [1}.Silane coupling agents, used widely for the modification of silica surfaces, have also been employed more recently for modification of layered silicates [2,3,4,5]. Modification with organosilane involves grafting reactions by establishing covalent bonds between the reactive groups of the layer, normally hydroxyl groups, and silane molecules. These reactions can be restricted to the external surface (the basal spacing remains unchanged) or to the interlayer surface, in which case an interlayer expansion occurs. The resulting material can be defined as a hybrid material or, more specifically, functionalized inorganic layered material [1]."

Jan 1, 2008

By Ryuhei Masuda, Kenji Oosumi, Yasuhiko Watanabe, Yutaka Nagakura, Tomoya Ohzono

"In order to promote recycling of aluminum scrap, it is required to remove inclusions that have a remarkable influence upon the product quality. An internal filtration technology using a new filter, which is made by coating an adhesive on the surface of the conventional filter, has been developed as a new removing technology for inclusions.The technology has made it possible to remove inclusions as small as 10-20µm in the molten metal, which have been impossible to be removed by the surface filtration technology using conventional filter, An inclusion removal rate of up to 90% has been attained.The technology will contribute not only to recycling of aluminum products but also to the improvement in the quality of current products."

Jan 1, 2000