Search Documents

By W. Petruk

The behaviour of galena, chalcopyrite and tetrahedrite during floration of a fine-grained base metal ore from New Brunswick was investigated by image analysis study of the mill concentrates and tailings. The minerals were analyzed to determine the grades and recoveries as related to free and unliberated mineral grains and their size distributions. The results show that only 37 wt % of the galena was liberated but 88 wt % of the free galena was recovered, indicating good mill performance for the lead. The lead recovery was 65 wt %, with the main loss due to unliberated galena. Most of the unliberated galena lost to mill tailings is so fine-grained that galena liberation and Pb recovery would not improve significantly by re-grinding. Chalcopyrite liberation was 56 wt % but only 75 wt % of the free chalcopyrite was recovered. Copper recovery was 45 wt %, with the chalco-pyrite loss in the mill tailings being both as large free grains, and as small and large unliberated grains. It was calculated that copper recoveries could be improved about 8 to 10 wt % by changing the concentrator operations and by regrinding. Concentrator operations hive already been modified and copper recoveries have improved about 5 wt %. About 29 wt % of the silver was lost to tailings mainly as both free and unliberated, large and very small, Silver-bearing tetrahedrite grains. It was calculated that about 25 wt % of the silver in the tailings might be recovered by improved milling conditions and by regrinding.

Jan 1, 1981

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By A. Mezei

Samples of cobalt and bismuth concentrates produced from the NICO deposit in Northwest Territories were subjected to a comprehensive metallurgical testwork consisting of: pressure oxidation, ferric chloride leach and carbon in leach, to recover the cobalt, bismuth and gold, respectively. A specific testwork program was designed to allow for the optimization of process parameters under multiple restrictive criteria. The overall objective was to establish leaching sequences that could produce acceptable recoveries while generating environmentally disposable residues as well as solutions suitable for further processing. The recoveries for the leaching stage, under the optimum conditions, were 97% for cobalt and 95% for gold, in the case of the cobalt concentrate. The bismuth concentrate produced recoveries of 99% for bismuth, 99% for cobalt and 97% for gold, respectively

Jan 1, 1999

By H. Y. Sohn, S. PalDey

"A new chemical synthesis process for the preparation of intermetallic compounds has been developed. It involves the vapor-phase reduction of mixtures of constituent metal chlorides by magnesium vapor to produce intermetallic compounds in the form of fine powder. The advantages of the process include (a) the use of inexpensive raw materials, (b) low reaction temperatures, and (c) products in the form of fine particles. Titanium and nickel aluminides were prepared by this method. The effect of AlCl/TiCl3 partial pressure ratio on the formation of different titanium aluminides was studied. A two-phase mixture containing 80 mol % of TiAl and 20 mol % of TiA13 formed at an AlC13/TiC13 ratio of 10. The amount of TiA13 was maximized to 72 mol% at an AlC13/TiC13 ratio of 16. The maximum conversion of the limiting chloride TiCl3 was 94 % . In the case of nickel aluminides, NiAI, NiAl3, and Ni2Al3 were formed by reducing mixtures of NiC12 and A1Cl3 vapors. The effect of the partial pressure ratios AlCl3/NiC12 and Mg/NiC12 on the formation of nickel aluminides was studied. The maximum content of NiAl obtained was 98 mol % . At the AlC13/NiC12 ratio of 19, a two-phase mixture of 17 mol% of NiAl and 83 mol% of NiA13 was produced. The product particles were very fine in the size range of 0.05 to 0.2 µm.A. IntroductionIntermetallic compounds are attracting much attention [1]. Titanium and nickel aluminides have attracted a great deal of attention from the aerospace as well as automobile industries because of their potential for high-temperature application (e.g., low density, good oxidation resistance, and high-temperature strength retention [2, 3]). Gamma TiAl and two-phase (TiAl and Ti3Al) alloys [4] are used for gas turbine engine rotational components as well as automobile exhaust valves. TiAl3 is one of the most extensively investigated aluminum-rich intermetallics. Nickel aluminides are attractive because of their low densities, relatively high melting point and good high-temperature strength properties. For example, Ni3Al shows increasing rather than decreasing yield strength with increasing temperature [5]."

Jan 1, 1998

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By N. Kanarin

A thermodynamic study is reported on the chlorination of Fe(1-x.)O, Fe2O3, Cr2O3, MgO, Mg2SiO4 with chlorine in the presence or the absence of reducing atmospheres. The reactivities of these compounds as well as that of Mg3Si2O5(OH)4 using Cl2+N2, Cl2+air, and Cl2+CO gas mixtures were studied by non isothermal thermogravimetric analysis between 20 and 1000 °C. The same solids were chlorinated in a horizontal experimental set, during two hours between 350 and 1000 °C, in reducing and oxidizing atmospheres: The chlorination products were examined by XRD and SEM, and possible reaction paths were examined. Results indicate that the carbochlorination of these solids was better than their chlorination; Furthermore, the carbochlorination was performed at lower temperatures than those of the chlorination. Finally, the reaction extent was higher in the case of carbo-chlorination of these compounds. Based on these results, a process was suggested for the selective recovery of chromium compounds from the chromite concentrate.

Jan 1, 1995

By T. Wang, R. G. Reddy, D. Mantha

"A new eutectic LiN03-NaN03-KN03-KN02 quaternary molten salt system was calculated using thermodynamic modeling. The eutectic temperature was predicted to be 100°C. The melting point and heat capacity of the salt eutectic composition were determined using DSC. The experimentally determined melting point is in excellent agreement with the predicted value. The melting point is more than 124°C lower than that of the KN03-NaN03 solar salt. The density of the molten salt was experimentally determined as function of temperature. Using the density, heat capacity and the melting point, thermal energy storage density and gravimetric storage density of the quaternary molten salt were calculated and compared with that of solar salt. The larger storage density value of this molten salt indicates that this salt has a better energy storage capacity for solar power generation systems.IntroductionMolten salts have been used as thermal energy storage media for solar energy applications. Nitrates are being used in the solar energy applications for their low melting point, low unit cost, high heat capacity, high thermal stability, negligible vapor pressure and high energy storage density [l]. Solar salt (NaN03/KN03: 60/40) is the most popular thermal energy storage medium which is currently being used with the freezing point of 221 ·c [2]; another ternary system HITEC® which contains NaN03, KN03 and NaN02 has freezing point of 141°C [3]. Newer nitrate salt mixtures are being studied and projected as potential candidates for thermal energy storage (TES) and heat transfer (HT) applications. Based on these favorable features, molten salt can work directly as the energy storage medium below 500°C [l]. Development and synthesis of newer molten salt mixtures with freezing point lower than those currently used for thermal energy storage applications is necessary for sustained utilization of solar energy. The approach to develop lower freezing point molten salt mixtures is by the prediction of new eutectic mixtures and also by the development of new nitrate compounds."

Jan 1, 2012

By V. Tsukerman, Ivanovam L.

"The potential of hydrocarbon resources in the Arctic oil and gas provinces is enormous. Oil, gas and condensate constitute the basis of mineral resource base of the shelf zone of the Russian Arctic; summary volume of hydrocarbons exceeds 100 billion tons of conventional fuel. Only in the Shtockman gas condensate field in the Barents Sea explored balance reserves equal to 3.2 trillion m3 of gas. It is necessary to establish a special regime of nature management in the Arctic. Environmentally oriented economic activities should be more actively stimulated. The Energy Strategy plans that starting from 2010 in the Barents and Pechora Seas up to 10 million tons of oil and 50 billion m3 of gas will be extracted, reaching the level of 30 million tons of oil and 130 billion m3 of gas in 2020. This task cannot be solved without intensification of geological exploration on the continental shelf. IntroductionThe elaborated strategy of mining enterprises should correspond to the modern paradigm of mining industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the Arctic zone of Russia which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents"

Jan 1, 2008

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By Guy Deschênes

Thiourea solutions can be used as leach liquors to treat gold ores or slimes. It is also efficient to elute resins or strip solvents that were loaded in cyanides solutions. The hydrogen pressure reduction is a practical step to recover gold and silver from leach solutions, and strips and eluates without any destruction of thiourea. It is a critical point because these processes have to consider the recycling of the liquors to be irore economical. The effect of temperature, pressure, acidity, compotation of the solution and the nature of catalysts on pressure reduction by hydrogen were investigated. An electranetallurgical study was? carried out to investigate the mechanism. The composition of the products was studied by different analytical methods. The process shows a good selectivity to precipitate gold and silver in a thiourea solution containing iron and copper. Gold and silver concentrations can be decreased to 0.2 ppm and 0.1 ppm at respectively 70 KPa H2 and 28°C. No decomposition of thiourea was evident during the tests. Metals such as nickel powder or platinum activate the reaction and improve the reduction.

Jan 1, 1989

By Songsong Wang

Recently, replacing Pierce-Smith converting process with the oxygen bottom-blowing continuous converting technology has become a new research focus. Based on the principle of Gibbs free energy minimization, the thermodynamic model of oxygen bottom-blowing continuous converting multiphase equilibrium system has been established. The elements distribution behavior is calculated at the same burden composition and operation parameters as the industrial production. The results show that the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in crude copper are 0.06, 0.0030, 0.070, 0.38, 0.39, 0.020, 0.017, 0.034, 0.010, respectively, and the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in slag are 0.53, 0.81, 0.020, 0.23, 2.5, 0.0048, 0.0010, 0.0030, 1.49, respectively. The calculated results agree well with the actual industrial production data, indicating that the model can be well applied in the oxygen bottom-blowing continuous converting practice.

By Guy L. Fredrickson

A modified transpiration reactor was used to measure the composition of the equilibrium gas phase formed above compounds in the Hg-O-S system at high temperatures (600 to 900K). A thermodynamic database {(AGo°f AH°t. AS°t)} for-HgO, HgS, HgSO4, Hg2SO4, HgSO4?HgO, and HgSO4?2HgO was developed based on the experimental results. Prior to this study, only estimated data were available in the literature for the sulfates and oxysulfates at temperatures above 298K. A series of vapor pressure' stability diagrams were constructed from 473 to 973K with isobars of Hg(g), HgO(g), S2(g), and SO3(g). These diagrams were found to be significantly different than those available previously and do provide insight to the phase relations of importance during the thermal processing of Hg-containing wastes. The thermodynamic results were used to conduct a series of Gibbs energy minimization calculations for a thermal processor' afterburner system for the treatment of HgS-containing wastes. The retention of Hg in the discharge calcine was examined as a function of temperature and excess air. Hg was found to report to the calcine as HgSO4, Hg2SO4, or HgSO4 HgO depending on the process conditions, and Hg retention occurs at temperatures as high as 930K. The precipitation of Hg-containing phases from cooled afterburner discharge gas starts at approximately 900K and the cooling of the gas an additional 30K (to 870K) results in over 50% of the Hg being preCipitated as HgS04?HgO. It was also determined that for small amounts of Hg present in sulfide concentrates during roasting, the Hg will be retained as HgSO4 or HgSO4?HgO at temperatures as high as 870K.

Jan 1, 1996

By Hidekazu Nakagawa

We investigated the anodic dissolution behavior of titanium in TMHA-Tf2N molten salt, which has a wide electrochemical window of about 5 V, in order to develop an electrodeposition method for titanium. By etching a titanium electrode in HF?HNO3?H3PO4 solution, the titanium electrode became electrochemically active, and a redox reaction was observed at around -0.15 V vs. I-/I3- in (TMHA-Tf2N)?HTf2N solution. We identified the redox reaction consists of the reduction of the proton and the oxidation of hydrogen. The diffusion coefficient of the proton in TMHA-Tf2N was calculated to be 6.9 10-8 cm2 s-1 at 50 °C from the cathodic peak current in the cyclic voltammogram. Anodic decomposition of the molten salt was not observed up to 6.0 V vs. I-/I3- on titanium electrode, while it was observed at around 2.0 V vs. I-/I3- on platinum and glassy carbon electrodes. Cathodic decomposition of the molten salt was observed at around -3.0 V on the titanium electrode, as well as on the platinum and glassy carbon electrode.

Jan 1, 2006

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

There are mainly three commercial nickel laterites in Turkey: Gordes, Caldag and Sivrihisar. The first two appear in Western Anatolia. The third one, Sivrihisar (Yunusemre) laterites have been found in the first decade of the millennium, in the Central Anatolia region of Turkey. Since then, mining facilities have been continued in Yunusemre. Calcination, prereduction and smelting of Sivrihisar laterites have been extensively studied and published. In the current work, some results of the studies related to characterization of Sivrihisar laterites will be presented.

Jan 1, 2016

By George Oprea, Tom Troczynski, Joe A. Rigby, Waiman Lo

The refractory lining of the tuyere line in Peirce Smith converters have usually much shorter life in service than the rest of the lining, above or below it. There are already recognized chemical, thermal and mechanical factors which contribute to the wear of the lining. Our study presents the experimental results on microstructural changes occurring on these tuyere line bricks in a nickelcopper converter. The experimental bricks, after use at the tuyere line, were investigated using SEM/EDS and XRD techniques, to identify the mineralogical changes due to interactions with the nickel-copper matte or fayalite type slag at the process temperatures. The microstructural changes were correlated with physical and mechanical properties of the brick before and after use and a wear mechanism was suggested. Although the matte does not theoretically react with the mineralogical components of the brick, a partial oxidation of the Ni-Cu sulphides was identified using a line analysis by SEM/EDS in the densified layer at the hot face, which allows for mineralogical changes at the matte-refractory interfaces, with a high probability of microcrack formation due to the thermal cycling during use. These microcracks were also identified to open through inter-granular fractures parallel to the hot face, which appeared to be the main cause of lost lining during use. The reactions between the fayalite slag and refractory brick could eventually play a role in chemical dissolution of the brick only in the superficial layer at the hot face, as no slag components were identified deep into the brick.

Jan 1, 2009

By Richard A. Shulkosky

The American Iron and Steel Institute (AlSO, in conjunction with the U.S. Department of Energy (DOE) jointly funded the development of a mechanical properties model for Hot Strip Mills. INTEG process group, inc. validated an enhanced version of the model under a project funded by the AlSI/DOE Technology Roadmap Program (fRP). The Hot Strip Mill Model (HSMM) version 6.0 allows users to easily set-up their mill configuration, simulate a rolling mill schedule and calibrate the model for a variety of grades of steel. Starting from reheat furnace drop out, the model simulates roughing mill stands (reversing and continuous), heat retention equipment (coil box and covers), finishing mill stands (tandem and Steckel mills), the run out table and the mill exit area. The HSMM uses a series of physical models to calculate both the thermo-mechanical and the microstructure evolution of steel being processed in a hot mill to predict its final mechanical properties. The enhanced HSMM was validated using a multitude of samples from several steel companies. Excellent agreement was obtained for tensile strength. The supporting steel companies have utilized the model for a variety of practical applications. Keywords: Process Modeling, Microstructure Evolution, Mechanical Properties

Jan 1, 2003

By Mari Naess, Jan Erik Olsen, Gabriella Tranell

"Fume, also known as dust, is produced during metal refining. Exposure to fume is damaging to the health of plant operators. A mathematical model has been developed to study the different factors governing the fuming mechanism. It is shown that natural convection is the main driving force of the phenomenon, and that the fuming rate is highly sensitive to the area of the exposed metal surface. A new feature introduced in the modeling concept is the ability to include a gas flux of unconsumed process gas flowing up through the metal surface. This reduces the fuming rate, and should normally not be neglected.IntroductionFormation of fume from the ladle in which metal is refined into its final specifications is an environmental issue of importance for the working environment in the production plant. In layman-term fume is often known as dust. It is formed when metal reacts with oxygen. As an example of a fuming process, we will focus on ladle refining of silicon. Note that many of the principles and conclusions will apply to other metal refining processes. For silicon production, silica fume (S1O2) is produced when silicon metal (Si) reacts with oxygen (O2).Silicon is produced in a submerged arc furnace. The metal is tapped from the furnace into a ladle for refining. The refining is conducted by injecting a mixture of air and pure oxygen at the bottom of the ladle. The oxygen reacts with the metal and the impurities, and the amount of impurities is reduced according to product specification. At the ladle surface, metal also reacts with oxygen present in the air surrounding the ladle. This reaction produces silica fume as illustrated in Figure 1."

Jan 1, 2012

By R. W. McCallum, B. Jensen, K. W. Dennis

"There are substantial challenges in the exploration of magnetic materials in the R-TM-X system (R =rare earth, TM= transition metal, X =stabilizing element) where Xis an element which has high vapor pressure, high reactivity, toxicity, or a refractory nature. This research focuses on discovering new phases with high anisotropy and high magnetization through closed diffusion couples inside high purity Fe crucibles. Either vapor-solid reactions or powder metallurgy techniques are then employed to isolate a stoichiometric sample based on a potentially magnetic phase found in the diffusion couple. For this research, X = F, Ca, Sr, Se, Zn, Bi or Cd, TM= Fe, and R = Nd. New ternary phases have been discovered with WDS and EDS, and magnetic transition temperatures have been measured with a SQUID magnetometer and VSM.IntroductionSince the discovery of the RCo5 compounds in the 1960s, rare earth- transition metal (R-TM) magnets have been the main focus of permanent magnetic research over the last five decades. Iron-based magnetic materials were studied next in attempts to avoid the unstable price of cobalt as well as the high price of Sm, the top performer in the RCos and RzC011 series. This hunt eventually led to the discovery of Nd2Fe14B with a theoretical BHmax of 64 MGOe, nearly double that of the previous samarium based magnets. The next few decades were devoted to enhancing the magnetic properties ofNd2Fe14B by the improvement of processing techniques and the additions of alloying elements. The only complete elemental substitution discovered in this system was R1Fe14C, which did not improve magnetic properties. It is probably safe to say that most ternary R-TM-X systems, where Xis any element that may stabilize a ternary phase, have been investigated if they may be prepared by conventional processes such as arc or induction melting. The present study offers a systematic approach to developing a novel diffusion couple technique in which the volatile, reactive or toxic alloying elements are laser welded inside a high purity Fe crucible. This experimental setup will prevent the oxidation of the rare earth element, as well as contain the volatile X element. As the goal of the research was to find new rare earth permanent magnets, only phases which contained greater than 60 wt% Fe were investigated. 247"

Jan 1, 2012

By William Petruk, J. H. Gilles Laflamme, Jean Robitaille, Louis J. Cabri

"A quantitative mineralogical study using ore microscopy, electron microscopy, proton-microprobe, image analysis, and material balances was done on samples from the circuit of a concentrator in Quebec, with particular emphasis on the Cu concentrate. The ore contains many different minerals, of which the principal ones, in decreasing order of abundance, are pyrite, sphalerite, chalcopyrite, bornite, galena, tennantite, and pyrrhotite. Minor to trace amounts of covellite, chalcocite, stannoidite, mawsonite, colusite, wittichenite, miharaite, hessite, petzite, electrum, and an unidentified Cu-Pb-Bi-sulfide also occur.Liberation of pyrite is very high in all size fractions for all samples (ranging from 80-91 %). Liberation of chalcopyrite, bomite, sphalerite, and tennantite is relatively high, on average, in the head .sample and Cu concentrate (55-78% and 66-88%, respectively). Most of the chalcopyrite in the flotation tails is not liberated, whereas about one half of the tennantite and sphalerite are liberated in both the flotation and :final tails. Recoveries calculated for the Cu concentrate (on the basis of assays, mineralogy, and image analysis) are chalcopyrite 72. 5%, bornite 73. 7%, sphalerite 41.0%, tennantite 70.9 %, and galena (together with some trace minerals) 34.2%. It was also calculated that the Cu concentrate contains 10.0 % of the pyrrhotite and i.4 % of the pyrite.Materials balance calculations were done on the five major sulfide minerals to determine the mineralogical distribution of 13 major, minor, and trace elements (as determined by protonmicroprobe analyses). It was determined that tennantite is the principal carrier of Bi (67%), As (90%), and Te (86%) in the Cu concentrate. Therefore, removal oftennantite, which is mostly liberated in the Cu concentrate would significantly reduce these three contaminant elements, but at a loss of9% of the Cu, 2.0% of the Zn, and 0.7% of the Ag. The precious metals (Au, Ag) occur as discrete minerals (electrum, petzite, hessite). Some of the Ag also occurs in solid solution in bornite (23.1% of Ag in Cu concentrate), tennantite, and sphalerite. Four of the major sulfides (chalcopyrite, bomite, sphalerite, tennantite) in the ore also contain measurable concentrations of the following trace elements: Se, Cd, In, Sn, and Sb, occurring mostly as solid solutions. Some of these elements are also concentrated (up to about 18%) in minor and trace minerals such as colusite, stannoidite, and mawsonite."

Jan 1, 1999