Search Documents

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By R. L. Player

"The Copper Isasmelt process has been developed over the past 15 years by Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organisation (CSIRO). The first two commercial plants were commissioned in mid 1992.The results of four heat balances on the Mount Isa plant are presented. At a smelting rate of 98 t/hr of chalcopyrite concentrate plus 14 t/hr reverts, the total heat generated was -91MW. Approximately 39% of this energy came from coal, while 50% of the energy reported to the process waste gas. To a first approximation the furnace is near chemical equilibrium.The impurity distribution in the Mount Isa plant was presented. Approximately 91 % As, 85% Cd, 75% Bi, 68% Zn, 60% Sb and Tl, 45% Pb and 30% Te in concentrate was eliminated from the matte.The ""bubble"" frequency of the gas cavity below the foot of the lance was measured at -2. 1Hz. Side bands displaced by -l.lHz modulated the bubble frequency. This was consistent with radial gravity wave motion in the slag bath. The two processes, gas bubbling and wave motion appeared to be coupled together; the bubble frequency was twice the slop wave frequency. IntroductionCopper Isasmelt has been developed over the past 15 years by Mount Isa Mines Limited and the Commonwealth Scientific and Industrial Research Organisation. The process is based on the Sirosmelt lance, invented by researchers at the then Division of Mineral"" and ProcessEngineering ofCSIRO in 1973.The first two commercial scale copper furnaces were commissioned at Mount Isa and the Cyprus Miami Mining Corporation smelter at Miami, Arizona in August and June 1992 respectively.The process concept, the history of the development, and the Mount Isa plant have been described (1, 2, 3).This paper sununarises heat balances obtained on the furnace, the impurity distribution among the output streams and lance injection characteristics."

Jan 1, 1996

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By Gavin Lind

The Minerals Council of Australia (MCA), through its Minerals Tertiary Education Council (MTEC), builds capacity in higher education in the core disciplines of mining engineering, metallurgy and minerals geoscience. Over the past fourteen years, this all-of-industry approach in securing the long-term supply of these critical skills (which remain a chronic skills shortage for the Australian minerals industry) through nationally collaborative programs across sixteen Australian universities delivers spectacular and sustainable results for the industry. These unique, world-first programs are built on a healthy platform of dedicated industry funding and in-kind support and forms part of the MCA’s broader uninterrupted, sustainable education and training pathway to increase workforce participation, workforce diversity and workforce skills, regardless of the business cycle in the industry. This paper will highlight the origins, iterations and current successful programs of MTEC, including its future vision, and presents a mechanism for industry and academia to collaborate to address future professional skills needs in the minerals industry globally.

Jan 1, 2014

By Hu Long

In this, the first systematic study of the oxidation of orpiment (As2S3) in sulfuric acid solution under oxygen pressure at temperatures above 170°C, the effects of retention time, temperature, particle size, oxygen partial pressure, the concentration of sulfuric acid and pulp density were evaluated. The effects of cupric and ferric ions on the oxidation rate of As(III) to As(V) were also examined. The products of oxidation are As(III), As(V), SO42- and elemental sulfur. At temperatures ranging from 170 to 230°C, most of the arsenic was found to be in the trivalent state, and oxidation to As(V) with oxygen was very slow. This was confirmed by attempting to oxidize a synthetic arsenious solution. However, the rate of oxidation of As(III) to As(V) is rapid in the presence of ferric ion. Elemental sulfur was found at all temperatures investigated, which can be further oxidized to sulfate at high temperature.

Jan 1, 1999

By Faustino G. Prado

In the, quest for an economical and environmentally friendly reclamation of metallurgical dusts generated during pyrometallurgical operations, our goal has been the separation and recovery of most of the components, as well as the complete recycle of all the reagents. Effluents have been avoided, within acceptable economic parameters. This presentation, which can be applied to a large spectrum of dusts and other residual-materials-, has focused on the dusts generated by the operation of Secondary Copper Smelters. Those dusts show a wide range of components, including zinc, lead-, copper, cadmium, tin, chlorine and-alkalies. Our present work deals with the use of ammonium salts in the separation and recovery of-the above mentioned elements in a marketable form. Most of the chemistry and techniques involved have teen already confirmed in commercial scale operations. Others have gone through pilot scale tests or bench scale tests. The recycle of reagents has also been- confirmed at the same operating levels. A preliminary evaluation indicates that the chosen route, in addition to a viable economy, offers a complete and safe reclamation within the most strict environmental regulations.

Jan 1, 1995

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By Zuhair A. Munir

"The use of self-propagating combustion reactions to synthesize metallic, ceramic, and composite materials is described. The limitation of this process because of the porous nature of its products is discussed. The formation of dense bodies through the simultaneous application of pressure is shown for a metal-matrix composite. The effect of an external electric field on the synthesis of ceramic and composites is described. The nature of the effect of the field on the mechanism of synthesis is analyzed theoretically and experimentally. The use of the self-propagating combustion to synthesize intermetallic thin films is presented for the Ni-Al and Ti-Al cases. The formation of functionally gradient materials (FGM) by centrifugally-assisted self-propagating high-temperature synthesis is described.IntroductionThe use of self-propagating combustion reactions for the synthesis of a large number of simple and complex materials has been described in numerous publications. These have been amply discussed in several review articles [1-4]. The many benefits of this method of materials synthesis are commonly examined in light of its most significant limitation: the porous nature of its products. The porosity in the products of self-propagating high-temperature synthesis (SHS) is an intrinsic characteristic of the process and its elimination has been the focus of numerous attempts. Various experimental methods have been used to accomplish this goal."

Jan 1, 1994

By Makoto Ohlsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SME). The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force. The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films. The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a Ni50Mn25Ga25 or Ni52Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace. The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains. After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature. The martensitic transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated. After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found. The constraint-aged films also showed the two-way 3ME by thermal cycling.

Jan 1, 2003

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By Shuqiang Guo, Xionggang Lu, Yuyang Bian, Weizhong Ding, Lan Jiang, Kai Tang, Changyuan Lu

For recovery of rare earth elements from the NdFeB based permanent magnet scraps, a high temperature process was used. Permanent magnets scraps were firstly oxidized in air. The optimal oxidation conditions under air are at temperature of 700oC holding for 30min. After the oxidation process, the oxides were reduced by graphite crucible at 1500oC under Ar atmosphere. By this way, the rare earth elements were recovered in the form of oxides, and Fe was separated to the metal phase. Boron distributed in both the rare earth oxides (REO) containing slag and the metal phase. In order to reduce the boron contents in the rare earth oxides, the carbon saturated iron bath and NdFeB added carbon saturated iron bath were used to refine the slag. By this process, the rare earth oxides with a comparatively high purity of 98.2% were gotten.

Jan 1, 2015

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company's Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By Reuben John Mathew

"Oxygen evolution is the main anode reaction in industrial copper electrowinning. The oxygen bubbles do not conduct electricity, thus increasing the electrolyte resistance. The oxygen bubbles formed at the anode rise to the surface, occupying a larger volume of the electrolyte at the top of the cell than at the bottom. This oxygen bubble concentration gradient contributes to a gradient in electrolyte resistance and consequently a tendency toward uneven current distribution. This phenomenon increases the chance for uneven growth on the cathode and/or short-circuits, particularly on the lower portions of the cathode. This issue may be ameliorated by increasing the charge transfer resistance for oxygen evolution down the height of the anode. This concept was studied by solving the current distribution for a 2-D model of a copper electrowinning cell using COMSOL.IntroductionA copper electrowinning tankhouse aims to operate at the highest current density that will deposit on the cathode a layer of copper metal possessing the desired physical and chemical characteristics. The operating current density is directly related to the physical nature of the copper deposit on the cathode (Figure 1), limiting a copper electrowinning tankhouse to some operating current density that produces acceptable copper deposits.[!] The ratio of the operating current density to the limiting current density is typically around 0.3.[2] If the limiting current density for a cell could be raised, the operating current density could also be raised and thus result in savings in capital cost for a tankhouse. [3]The average operating current density in a copper electrowinning plant is 270A·m- 2 .[4] The value for average current density, however, obscures the fact that the face of a cathode does not experience this value equally. Indeed, the current density varies along the height of an electrode and is independent of the height of the electrode.[5] This phenomenon partly explains why the lower portions of a cathode tend to display a rougher copper deposit.In order to utilize a higher operating current density but still remain at 30% of the limiting current density, the limiting current density must be raised, but it is affected by the mass transfer regime at the electrodes. The mass transfer regime is currently poorest at the lower portions of the cathode and this is part of the reason for the tendency for poor cathode deposits to occur at the lower portion of the cathode.[6]"

Jan 1, 2012

By Xiaorong Liu

Interfacial emulsion generated in copper solvent extraction is an inhomogeneous O/W emulsion that consists of organic phase, aqueous phase and solid particles. In order to determine what kind of components in organic phase promotes the emulsion, the organic phase separated from the interfacial crud provided by Dexing Copper Mine in Jiangxi, China was analyzed for its components by combined gas chromatography-mass spectroscopy. It was found that many kinds of emphiphiles containing such hydrophilic groups as carbonyl, carboxyl, or acylamine existed in organic phase, most of which were originated from the reagent degradation. Conclusively, Lix984N would degrade gradually during a long-term contact with the acidic aqueous feed and strip reagents. Lix84 and nonylphenol, as effective components of Lix984N, degraded almost completely after long-term recycling. As a result, the effective components of Lix984N were far lower in concentration than the dense-aromatic impurities derived from the diluent and the degradation products in total. The degradation of Lix984N would deteriorate solvent extraction, disengagement performance and result in more serious interfacial emulsion.

Jan 1, 2006

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992