Search Documents

By Baozhong Zhao

Experimental results have shown that fluxing with soda ash (Na:zC03) can remove As and Sb from molten copper at the rate of As>Sb, but is relatively ineffective in removing Hi. The rate of impurity removal is controlled by impurity mass transfer in the metal phase. In this paper, a mathematical model was developed to describe the impurity removal phenomena. The model incorporates the effects of molten bath mixing intensity, soda ash feeding rate, oxygen content in the molten copper and soda ash fluxing by surface addition and injection. The model predictions are in good agreement with experimental results and may be used in designing large scale tests.

Jan 1, 1996

By J. Fraser Forbes

"The meaning of the term ""process control"" has evolved significantly since its widespread use began in the manufacturing industries in the 1940s. Further, the scope of process control applications has drastically increased both in terms of the breadth of industries using process automation technologies and the vertical integration of these technologies within a single industry. This evolution and integration of process control technologies within the manufacturing industries has proceeded to such an extent that process automation is an integral part of modern business practices.This paper will examine the current status of process control technology from simple process regulation through process performance optimization to business planning. Each layer of the operations automation hierarchy will be discussed both in. terms of the current state-of-the-art and the directions in which these technologies are evolving. The key tools and tasks necessary for success at every level of the automation hierarchy will be introduced. Finally, the critical challenges that must be faced in accomplishing the goal of complete Computer Integrated Manufacturing (CIM) will be described.Finally, although this paper addresses issues of practical importance to any manufacturing company, the discussions will be framed in terms of the particular challenges facing and the opportunities available within the materials manufacturing industries."

Jan 1, 2000

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits ofthis approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the S02 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia, limonitic ore from New Caledonia and garnieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potential followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Tao Zeng, Jianchao Li, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"The densities of the selected quaternary Ca0-5%Mg0-Alz03-Si02 slag with low silica were measured by the Archimedean method in a wide temperature range from l 723K to 1823K. Slag compositions were chosen based on five different levels of Si02 content between 0.00 pct and 11.40 pct. The MgO content was equaled to 5.00 pct. The mass ratio of CaO/Alz03 was varied from 0.67 to 2.14. The effects of temperature, Ca0/Alz03 ratio and optical basicity were studied. It is shown that density decrease approximately linearly with an increase in temperature. With the same Si02 content, the density decreases with increasing of CaO/Alz03 ratio and optical basicity. Based on the experimental data as the boundary of the homogenous phase region predicated by F ACTSAGE software, the mass triangle model is used to calculate the density of selected limited homogenous phase region. The results showed that the mass triangle model is working well.IntroductionIt is of great importance to measure density of slag melt not only to the theory research for melt, which that is directly amenable to the structure correlations of molten slags, but also to the industrial application. Many metallurgy phenomena such as inclusion formation in molten melt and its removing, slag foaming, slag-metal reaction are closely related to the density of slag. Density is also required to estimate other fundamental properties, like surface tension, viscosity, and thermal conductivity from thermal diffusivity so that a relatively complete picture in regard to the behavior of high-temperature molten oxides could be made."

Jan 1, 2013

By Patrice Chartrand, Halvor Dalaker, Philippe Ouzilleau

A size-dependant thermodynamical model for the carbon-hydrogen previously developed by Ouzilleau et al. [1] has been expanded here to include chemisorption of methyl groups. Gibbsenergy minimalisation calculations using FACTSAGE software on this model indicates that hydrogen bonding through methyl groups is energetically favoured as an intermediate between bonding as monoatomic hydrogen to edge hexagons (which is more favourable) and as monoatomic hydrogen to corner hexagons (which is less favourable). The model has also been applied to methane decomposition and oxide reduction using natural gas. A C-H solid solution as a thermodynamic description of the solid carbon phase influences calculations of carbon activity in metastable methane, and gives different results than when using graphite.

Jan 1, 2015

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001

By Pekka Hanniala

The Outokumpu Flash Smelting process today is the most feasible method for copper matte smelting. The economic feasibility of the process has always been one of the main decision making criteria in smelter projects. Thus, today about 50 % of the world primary copper production utilizes Outokumpu Flash Smelting Technology. However, in the future, environmental criteria will have stronger and stronger impact on decision making. Flash Smelting technology offers the best pollution control features of any process. today. It is foreseen that, in the near future, the global trend will be that all the smelters must decrease their emissions at an accelerating rate, compelling the smelters to make increasingly larger investments on environmental protection. In most of smelters ?today, Peirce-Smith converting and transfer of the molten material in ladles are the number one pollution source. The key today for copper converting and minimizing emissions is the Kennecott-Outokumpu Flash Converting process, which has proven to be the most effective converting method in terms of pollution control and, production efficiency including capital and operational costs. Outokumpu Flash Smelting technology is applicable also for small to medium scale smelters but the most interesting area is the upper capacity limit for smelting in one line, which has not yet been reached. We predict that by the year 2000 to 2005, there will be at least one smelter which produces 500,000 tonnes of Cu per year based on one Flash Smelting and Flash. Converting unit. The current state-of-the-art of the Outokumpu Flash Smelting - Flash Converting process is presented in this paper as well as some new options for copper production to be utilized in the near future but which are available already today.

Jan 1, 1998

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would be reduced at the new smelter to about a half of the sum of those from previous two 1 smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive offgases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By M. C. Ruiz

In the present study, the size distribution, Fo(v), of organic drops produced in a continuous-mixing vessel has been determined experimentally for various conditions. The organic phase used was a 1: 1 mixture of a salicylaldoxime (LIX 860N-IC) and a ketoxime (LIX 64-IC) in an aliphatic diluent (Escaid 103). The aqueous phase was a copper sulfate solution. The results indicated that an increase in stirring speed, extractant concentration, and pH produced smaller drops. The effect of the stirring speed was the most significant, decreasing the average volume of drops by 57 % for a change from 300 to 400 rpm. On the contrary, an increase in the dispersed phase fraction, copper sulfate concentration, and retention time produced larger drops. Changes in temperature from 23 to 30°C did not affect significantly the drop sizes. In all cases, the experimental drop size distributions could be accurately represented by a lognormal distribution.

Jan 1, 2001

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from solutions containing copper complexes and thiocyanate. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide in the effluent. The copper precipitate assays over 50% copper and presents good dewatering characteristics. After settling it can be separated from the effluent by filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First, pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper and cyanide were obtained in laboratory tests using industrial solutions. With this procedure, cyanocidic gold/copper ores could be treated economically by heap leaching, since the cyanide consumed by the copper impurities could be regenerated at very low cost (most of the cost of cyanide regeneration would be compensated by the copper credits). In order to achieve this, a bleed of the barren solution could be treated by the proposed method, and then recycled to the leaching step. The volume of solution to be treated should be large enough to keep a cyanide/copper molar ratio higher than 3:1. This would assure that copper does not cause undue interferences in the leaching or the carbon adsorption stages. If the thiocyanate content is low, the oxidation stage can be avoided, and the solution can be recycled to the leaching stage directly after the solid-liquid separation stage.

Jan 1, 1997

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By Senlin Xie, Wanlin Wang, Lejun Zhou

"The innovative development of multiphase slag in hot-metal treatment has attracted considerable attention due to the reduction of CaO consumption and minimal environmental emission. In order to improve the efficiency of dephosphorization and to reutilize the waste-slag as an alternative source of phosphate ores, it is important to increase the distribution ratio of P2Os between the solid solution (2CaO· SiO2-3CaO· P2O 5) and liquid slag. An investigation was carried out to study the effects ofNa2O and B2O3 on the distribution ratio of P2Os, the results indicated that the increase ofNa2O would enhance the distribution ratio of P2Os with the formation of solid solution (2CaO·SiO2-Na2O·2CaO·P2Os), while B2O3 has the opposite function, and changes the morphology of solid solution. The study would provide an instructive way for the design of multiphase slag and re-utilization of waste-slag.IntroductionIn order to meet the increasing demand for high quality low-phosphorus steel, it requires a high efficient hot metal dephosphorization process. The current slag system for hot metal treatment contains large amount of solid CaO dispersed in liquid slag, which introduced a large amount of CaO consumption due to its low solubility, especially when CaF2 was restricted due to the environmental concerns. Therefore, new refming method to improve the utilization efficiency of CaO by using a solid/liquid coexisting multiphase slag was proposed, and the studies regarding to solid solution formation mechanism, mass transfer behavior of phosphorus and the phase relationship for multi-phase slag have been conducted. [1-6]Normally, hot metal dephosphorization slag consists of CaO--SiOz-FeO--P2O 5, and it has been approved that 2CaO·SiO2 forms a solid solution with 3CaO·P2Os at the hot metal treatment temperature over a wide range of compositions. [7] Kitamura et al [8] pointed out that the (2CaO·SiO2-3CaO·P2O 5) solid solution plays an important role in dephosphorization, and it has been regarded as an absorbents for phosphorus to lower the phosphorus content in liquid phase, which makes it more capable for future dephosphorization. l Besides, the multiphase slag has the potential to be recycled as a source of phosphorus, if the (2CaO· SiO2-3CaO· P2O 5) solid solution could contain high phosphorus content, and it can be separated from FeiO matrix 8hase due to the large difference of their magnetic properties under the strong magnetic field. [10, 11]"

Jan 1, 2014

By K. Fagerlund

Methods for simulation of settler reactions, matte-slag separation and matte settling in copper flash smelting have been examined. The reaction, separation and settling phenomena of slightly oxidized chalcopyrite samples and cuprous sulfide-magnetite mixtures in fayalite type slags were examined at about 1300°C under inert atmosphere. Two methods based on introduction of molten samples of oxidized chalcopyrite concentrates or synthetic matte-magnetite mixtures onto the surface of molten iron silicate slag were tested. In the first method the samples were water quenched and polished specimens were studied and analysed using light optical microscope, scanning electron microscope, energy dispersive spectrometer. In the second method processes taking place after the introduction of samples onto the slag are followed "in situ" using X-ray transmission image monitoring. Great differences were observed in separation and settling behaviour of low and high grade copper mattes produced as a results of interaction of initial samples and slag.

Jan 1, 1997

By Masatsugu Morimitsu, Tian Zhang

"This paper presents a novel anode for oxygen evolution in acidic aqueous solutions to produce non-ferrous metals by electrowinning. The method to prepare the anode was thermal decomposition of a precursor solution, and the obtained anode consisted of Ru02-based oxide catalytic layers formed on a titanium substrate, in which the catalytic layer contains nano-oxide particles as the active component. The oxygen evolution potential was lower than amorphous lr02-Ta20s coated titanium anodes so that the cell voltage of electrowinning was further reduced with the amorphous Ru02-based electrode.IntroductionElectrowinning (EW) is used to produce high purity of non-ferrous metals, and the primary metal production of copper, zinc, nickel, and cobalt by EW consumes huge electric energy worldwide, which tends to increase with increasing demand of such metals. The reduction of electric energy consumption is a significant issue for electrowinning industry, which means that the cell voltage reduction is needed to realize more energy-efficient EW processes. Another issue is also indicated from environmental perspectives; i.e., an improvement in EW plant environment by eliminating hazardous byproducts and wastes. Such byproducts and wastes include lead oxide, manganese oxide, and acid mist.We have been developing the anodes for energy-efficient and environmentally friendly electrowinning processes [ 1-11]. The development has been successfully done with the invention of the smart anode, MSA TM (Morimitsu Smart Anode) [ 1-5], which has low polarization for the main reaction and high polarization for the side reaction, in which the main reaction is oxygen or chlorine evolution, while the side reaction is the anodic deposition of each or both of lead oxide, manganese oxide, and cobalt oxide. The anode consists of a valve metal substrate coated with amorphous or less crystalline oxide catalytic layers. One of the typical examples of such oxides is amorphous lr02-Ta20s, and the substrate is normally titanium plate or mesh. The most important point of the oxide is that the amorphization or less crystallinity induce the increase in the active surface area only to the main reaction, not to the side reaction, thereby the polarization of the main reaction being reduced.In this paper, we present the smart anode consisting of RuO2-based catalyst formed on titanium substrates for oxygen evolution in electrowinning. The preparation, characterization, and polarization behaviors of the anodes are shown, and the cell voltage data for zinc or copper electrowinning using the anodes are also presented."

Jan 1, 2012

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998

By J. Y. Hwang

Microwave heating is an attractive alternative to conventional heating methods because heat is generated directly within the microwave absorbing materials. It has potential to be utilized for selective heating and removal of specified components from a materials mixture. This investigation was undertaken to explore the potential of selective heating and burning of binders for foundry sand reclamation. Selected raw materials and binders used in foundry operations were tested to determine their receptivity to microwave heating. Time needed to reach 600°C and/or the maximum temperature achieved for samples irradiated by microwaves for twenty minutes under 800 W microwave power are reported. The microwave heating characteristics of the selected materials are summarized and discussed. The interactions between microwaves and the raw materials used in a foundry. such as silica sand. chromite sand and bentonite (clay) binder were studied. The results showed that chromite sand coupled well with microwave energy at ambient temperature while silica sand did not. This was expected because the major component of chromite sand. iron chromite (FeCr2O4). is a good microwave absorber. while quartz, which is the major component of silica sand, is a microwave transparent material at ambient temperature. Bentonite absorbs microwaves well because it contains a hydroxyl functional group and water molecules in its structure. It was found that the structure of bentonite was changed through microwave irradiation. Microwave heating characteristics of silica sand mixed with different amounts of bentonite binders were investigated. The presence of bentonite in the mixture improved the microwave heating of silica sand significantly. and bentonite was deactivated by the microwave processing.

Jan 1, 1995

By R. Y. Wan

Low grade sulfidic-carbonaceous refractory ore from Newmont Gold Company's Carlin deposit was microbially pretreated. The biological pretreatment process gave partial oxidation of the sulfidic components of the refractory ore but the preg-robbing carbon continued to be active resulting in approximately zero cyanide gold extraction. A 495 ton pilot plant test heap was conducted using acidic thiourea leach following biooxidation. Activated carbon and cation exchange resin adsorption were tested for gold recovery from the thiourea pregnant solution. The results obtained from the test heap were not satisfactory. Gold extraction was low due to slow reaction kinetics which was caused by relatively large particles and very low winter temperatures. Problems existed in the thiourea-test heap and are discussed in this paper. An alternative heap leach process using thiosulfate has been successfUl at the pilot scale for gold extraction following biooxidation pretreatment of refractory sulfidic-carbonaceous ores.

Jan 1, 1995

By John A. Herbst, William T. Pate

"Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen, and the coordination of all unit operations in pursuit of the highest performance level. However, several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of unit operations to account for critical interactions within and between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significaritly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated with the models and can be effectively optimized. Financial goals seems to be the objectives of choice.This paper discusses recent progress in overcoming the challenges and illustrates a promising approach which is being pursued at Mexicana de Cobre's La Caridad copper ore concentrator. At M de C, advanced control strategies have been installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, increased from 76,000 tpd to 90,000 tpd. Plantwide integration is expected to gain an additional 3% improvement in profitability."

Jan 1, 1996