Search Documents

By V. D. Tathavadkar

Natural chromite mineral is a solid solution of spinet end members namely: chromite (FeCr2O4), hercynite (FeA1204), magnetite (Fe3O4), magnesio-chromite (MgCr2O4), (MgA12O4), and magnesio-ferrite (MgFe2O4). A phase transformation in chromite minerals occurs in oxidising conditions during the soda-ash roasting reaction. This phase transformation plays an important role in improving the extraction efficiency of Cr3+ from mineral phase. The extraction efficiency of chromium (Cr3+) from chromite to a water¬soluble sodium chromate (Cr6+) salt depends upon the decomposition kinetics of the spinet phase. An investigation of the phase changes in chromite ores in the absence of sodium carbonate was carried out in air, argon, and in argon +5 % hydrogen gas mixture. The thermodynamics of phase transformation reaction in chromite solid solution phase is discussed using the solution model proposed by Sack and Ghiorso [1]. The microstructural changes and the changes in elemental compositions of different phases were examined by SEM and electron probe microanalysis (EPMA) respectively. The experimental results indicate that the solid solution spinet phase in chromite mineral undergoes spinodal decomposition under the influence of oxygen partial pressure and temperatures. The structure of phases formed and their morphologies suggest that the phase decomposition may be similar to those observed by Burkert et. a]. 121, although the scale of phase separation in chromite appears to be strongly dependent on oxygen partial pressure.

Jan 1, 2001

By C. A. Pickles

Microwave processing is a relatively new technology that has been successfully applied in a number of industries. However, in the field of metal extraction, there is a paucity of success, despite considerable hype in the early years. Increased reaction rates, lowered reaction temperatures and higher energy efficiencies were some of the advantages claimed. Even with over almost two decades of research and some pilot plant studies, microwave metal extraction remains essentially a laboratory technique. In this paper, the research performed over the last few decades will be reviewed and some reasons for the lack of success in developing microwave metal extraction processes will be discussed. Based on the knowledge gained from these experiences, a more informed view of microwave heating can lead to the realization that there is still some untapped potential for this heating technique in metal extraction processes.

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By I. B. Scorzelli

The aim of this paper is to make a detailed mineralogical characterization of a typical brazilian xenotime and zircon from the Pitinga Mine using SEMIEDS techniques, On the other hand, superficial pretreatments with HCI, HN03 and HF were done to evaluate the modifications on surface compositions and the morphology of the particles for flotation purposes, The studies showed that both xenotime and zircon present very small inclusions of thorite; zircon is strongly metamictizated given rise to malacon. The HF pretreatment deeply affected the morphology of the particles as well as the surface properties in relation to flotation.

Jan 1, 1996

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc, Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed,

Jan 1, 2003

By K. L. Money, R. R. Bleakney, R. H. Hanewald

The processing of EAF baghouse dusts, rolling mill scales, and belt grinding swarfs from the specialty steel industry will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions, filter cakes, spent nickel and chromium plating baths, super alloy wastes, and nickel-cadmium batteries. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery.

Jan 1, 2000

By Xu Weimin

The existing copper electrorefining tankhouse of Jinchuan Nonferrous Metals Complex (JNC) was commissioned in 1986 for refining blister copper anodes. Blister copper is produced by reverberating chalcocite separated from converter high grade nickel-copper matter by means of flotation. Special chemical analysis of the anodes shows, a composition of 93.02 - 95.72 % copper, 3.0 - 4.96 % nickel and 0.5 - 1.23 % sulfur. The wide range of composition makes the electrorefining process fairly different from others throughout the world. The initial nickel content of 20 ppm and sulfur 40 ppm or more in copper cathodes are reduced to 8.5 ppm and 11 ppm respectively. Since 1986 the tankhouse has undergone significant evolutionary modifications and implementations to ameliorate cathodes quality desirably. The important fact is that the N-additive was utilized through many studies and pilot and field trials successfully. While our primary purpose is to improve chemical quality of the cathodes, tankhouse capacity is increased considerably and the process is perfected satisfactorily. The tankhouse is described with special emphasis on JINCHUAN PROCESS. The upgrading of our product by the utilization of the N-additive is highlighted. The other aspects of the tankhouse including spent electrolyte treatment and by product nickel sulfate manufacturing are briefed as well. Key words: JINCHUAN PROCESS, anode, cathode, electrolyte, electrorefining, N-additive.

Jan 1, 1993

By Xuemei Zheng, Aiyuan Ma, Chao Liu, Guojiang Li, Chenyu Sun, Jinhui Peng, Libo Zhang, Yongguang Luo

In this paper, the removal of fluorides and chlorides from blast furnace dusts by water vapor enhanced microwave roasting was investigated, combined with the advantages of microwave selective heating and based on a thermodynamic analysis of zinc and lead halides. According to proposed reactions in the process, detailed experiments were systematically conducted to study the effect of roasting temperature, holding time, air flow, water vapor flow rates, and stirring speed on the efficiency of the removal of F and Cl. The results show that 97.26% of F and 64.23% of Cl could be separated when the condition of the roasting temperature of 650°C, stirring speed of 80 rpm, holding time at 60 min, air flow of 350 L/h and water vapor flow rate of 8 mL/min was optimized.

Jan 1, 2016

By Alicia Esther Ares

This study was conducted to investigate the directional solidification of Zn-20%A1 and Zn20% A1-1O%Si-3o/oCu alloys under different conditions of heat transfer at the metal/mould interface. The type of structure obtained in both cases was analyzed and related to the solidification thermal parameters such as cooling rate, growth rate, thermal gradient and recalescence which were determined from the temperature versus time curves. These parameters were correlated with the structure-like length of columnar grains and size of equiaxed grains. The metallographic analyses were done performing quantitative metallography and composition analysis of the different alloying elements along the cast samples by SEM (Scanning Electron Microscopy) and EDXA (Energy Dispersive X-Ray Analysis). Correlations between properties, structures and thermal parameters were found.

Jan 1, 2008

By Anupam Madhukar

The essence of an atomistic unified kinetic model of strained thin film growth and defect initiation is presented along with a comparison of its consequences obtained from computer simulations with experiments. Within the competing kinetics of a strain dependent activated incorporation of atoms and an asymmetry between upwards and downwards inter-layer migration, the model provides a consistent description of 2D versus 3D morphology evolution accompanied by the appearance of surface vacancies and steps at no energy cost. The correlated migration of these precursor defects offers an atomistic mechanism for the emergence of surface half-loops from the growth front (thus accounting for configurational and thermal entropy) governed by activation energies closer to their correlated motion under the evolving strain fields and thus substantially less than those calculated with respect to the perfect crystal as the reference state. The essential mechano-chemical nature of the problem is compared and contrasted with the historical literature of such phenomenon as precipitation hardening and sintering in metallic and ceramic composites.

Jan 1, 1994

By E. Charles Abbey

Manganese in electrolyte has both beneficial and detrimental effects in Zn electrowinning. Mn oxidizes to form MnO2 on Pb–Ag anodes, cell walls and pipes. MnO2 reduces anode corrosion but also leads to short circuiting and maintenance issues. MnO2 is thought to interact with chloride ions and produce oxidized chlorine species. The interactions between Mn and Cl are not well understood. Therefore, two sets of 45+ day bench scale experiments were conducted to investigate the effects of the manganese to chloride ratio on anode corrosion rate and electrolyte chemistry using rolled Pb–Ag anodes. Daily manganese and chloride losses from the electrolyte appeared to be correlated. Increasing the average Mn/Cl− ratio from ∼7:1 to ∼11:1 reduced the anode corrosion rate. Increasing the ratio above 11 did not reduce the corrosion rate further. Anode scales produced with Mn/Cl− ratios at and above 11:1 contained some γ–MnO2 while scales formed with ratios less than 11:1 did not.

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

By C. S. Ek

As a continuation of previous work, further tests have been carried out to recover silver from the residues obtained in a zinc jarosite process. Selective flotation has been performed with different reagents, and ?cleaning steps have been introduced to upgrade the silver concentrate. Leaching of crude residues, as well as flotation tailings, has been carried out with cyanide and thiourea. Finally, the different beneficiation methods are compared, and the industrial aspects? of their application are reviewed.

Jan 1, 1990

By Tam Tran

Over the last decade, halide (chloride, bromide and iodide) systems have been evaluated as alternative lixiviants for the processing of gold to replace cyanidation which has been widely used in commercial practice. This paper first reviews the development of processes promoted by Kaljas Ltd / Lachlan Resources (Australia) and Great Lakes Corp (USA) using different bromide/bromine systems in the early 1990's. Several research groups subsequently evaluated the use of iodide/iodine and chloride/chlorine for gold extraction, showing similar characteristics of gold/silver dissolution and recovery. A critique is :given on the advantages and the ,shortfalls of halide systems as alternative lixiviants. The stability of gold? halide complexes is discussed, based on practical experience and thermodynamic modelling of their speciation, The iodide system provides the most stable gold / silver complex for easier handling. However, the cost of iodide inhibits its application for are processing. In this critique, emphasis is given on the cheapest system, which involves the use of chloride for leaching (in conjunction with an appropriate oxidant). However the chloride-base leachant has a major drawback which is related to the unstable nature of gold chloride in a reducing environment.

Jan 1, 1998

By Musa Karakus

The sedimentary iron ores of Alsace-Lorraine, France have very high phosphorous contents that average 0.7% and are as much as 2.19% P. Ores from the Tucquegnieux and Joeuf mines have been studied by cathodoluminescence microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe analysis in order to fully characterize the mineralogy, size, shape, and distribution of the deleterious phosphate grains. The phosphorous occurs as collophane, a carbonate fluorapatite, in ten morphological forms, most abundantly as microcoprolites, but also as intraclasts, concentric layers, and cortices in ooids, phosphate replaced ooids and bioclasts, phosphatiC shells, fossil infillings and internal molds, fish teeth, phosphatiC laminae, and cements between the goethite ooids. About 95% of the phosphate grains are sufficiently large that relatively fine grinding fol'lowed by reverse flotation would be expected to be effective in significantly diminishing the phosphorous content of the concentrates.

Jan 1, 1989

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By M. Omneya El-Hussaini, M. Galal Abdel Wahab, A. Mohamed Mahdy, M. Fathi El Shahat

"Um-Gheig Pb-Zn representative sample was collected from the main adite of Um-Gheig mine along Red Sea coast in Egypt. Its chemical analysis shows that, it contains 16% Zn, 2.3% Pb, 0.1% Cd and 0.1% B as elements of interest. After H2SO4 agitation leaching, the chemical composition of Um- Gheig Pb-Zn deposit ore residue assayed 2.26% Pb, 1.5% Zn, 0.085 % B and 0.01% Cd. This residue was leached with 20% HCl at S/L ratio 1/3 for 2 hours at 80o C. The chloride leach liquor was found to contain 18 g/l Pb, 13 g/l Zn, 0.1 g/l Cd and 0.75 g/l B with the corresponding leaching efficiencies 79%, 86%, 100% and 88% respectively. Lead was precipitated from the chloride leach liquor using concentrated H2SO4 to obtain PbSO4 with precipitation efficiency 96%. While boron was extracted by the selective resin Amberlite IRA743 with loading efficiency of 80%. On the other hand, Zn and Cd were precipitated using Na2S solution with 86.7% and 100% recovery efficiencies respectively.IntroductionLead-zinc ores occur in Egypt in a few localities distributed along the Red Sea coast between El Qusier and Ras Banas.. The reserve of the ore deposits has been estimated by Soviet and German Experts to be about 900,000 Ton, [1]. Onal et al., [2] recovered Pb from Pb–Zn sample containing 10.17 % Pb and 10.98 % Zn from Aladag in Turkey. El-Sherif, [3] used concentrated HCl to leach lead-zinc ore sample of Um-Sammuki area in Egypt. As had been published by Marchioretto et al. [4], the precipitation of heavy metals with lime, sulfide and caustic soda are the most commonly used economical methods for metal removal. Lead was completely removed from the anaerobically digested sludge by precipitation with NaOH and Na2S at waste water treatment plants. Mahdy et al., [5] had successfully extracted boron from the bittern solution of Qaron Lake by ion exchange resin (Amberlite IRA 743). The extraction of boron was mainly depending upon the pH value. They extracted 80% of boron at pH 5.5, while at pH 3.9 about 74% boron was extracted. Kabay et al. [6] used the column-mode to remove 1g/l of boron from geothermal waste water of the Kizildere-Geothermal Power Station by using Diaion CRB 02 Nglucamine- type chelating resins. In this regard, the removal of lead, cadmium and boron allow the residue to be reclassified as non hazardous material."

Jan 1, 2008

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010