Search Documents

By K. Kalgraf

The motion and stability of the metal/electrolyte interface is determined by Navier-Stokes equation. The equation may be decomposed into two independent equations by taking the divergence and curl of Navier-Stokes equation. The divergence determines the motion and stability of magneto-gravitational waves. The curl of Navier-Stokes equation gives an equation containing only velocity and magnetic field, and states that the magnetic field is driving a circulation pattern in the cell, and this magneto-flow has its own stability conditions. The waves are called Alfven waves, and their stability properties are related only to magnetic field and geometry.

Jan 1, 2001

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction. The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory- scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the detennination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the detennined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors detennining the time of reduction.

Jan 1, 2003

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothermic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperature rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (> I 0 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By Chu Yong Cheng

The solvent extraction (SX) processes of the three pressure acid leach (PAL) nickel plants in Western Australia have been reviewed. The use of intermediate precipitation, solids/liquid separation and re-leach in the three W A nickel plants make these processes complicated and costly in capital and ?operation. The research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy I CSIRO Minerals has led to the development of direct solvent extraction (DSX) processes to recover and purify nickel and cobalt from leach solutions. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new DSX processes over the reviewed processes. By using a new synergistic organic system in semi-continuous tests with a pilot plant leach solution (after iron precipitation) from BHP-BiIliton Stainless Steel Materials, the metal values (Ni and Co) together with zinc and copper were separated from the major impurities (Mn, Mg and Ca, together with Cl) in the first SX circuit. The co-extracted manganese, magnesium and' calcium were easily scrubbed out. After stripping, the metal values (Ni and Co) together with zinc and copper were concentrated, resulting in a much smaller second SX circuit and equipment in the down stream processes. The extraction and stripping kinetics of the metals with the new synergistic organic solution were very fast. The extraction and stripping almost reached steady state within 0.5 minutes. Semi-continuous test work with a synthetic leach solution, a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton Stainless Steel Materials showed that manganese, calcium, copper and zinc can be effectively and efficiently separated from nickel, cobalt and magnesium by extraction, scrubbing and stripping. This led to the development of another DSX process using D2EHPA to recover nickel and cobalt from leach solutions.

Jan 1, 2003

By Richard Elliott

Current methods for producing low-carbon manganese alloying materials for the steel industry are energy intensive and costly. To enable wider implementation of high Mn steel alloys, a novel solid-state Mn ore reduction strategy is therefore being investigated. This solid-state process, modelled on existing Direct Reduced Iron technology, employs a methane-containing atmosphere to reduce Mn ore pellets to a metal carbide. These pellets may then be smelted, yielding a Mn-rich master alloy. It is well established that CH4 is a suitable reductant for Mn ore powders; however, the reduction behaviour of industrially relevant Mn ore pellets by CH4 is poorly understood. The present work reports the results of an investigation undertaken to address this knowledge gap. The results of this study highlight the significantly different reduction behaviour exhibited by the Mn ore pellets relative to the ore powder under similar conditions and suggest that the diffusion of CH4 into the pellet interior is the limiting factor in achieving complete reduction.

By I. Gaballah

High and low grade concentrates of tantalum and niobium oxides were obtained by leaching a medium grade tin slag. Chlorination and carbochlorinalion of these concentrates were studied between 200 and 1000 "C. Chlorination or carbochlorination of the low grade concentrate led, at 1000 OC, to the extraction of about 95 % of the tantalum and niobium oxides. However, the tantalum and niobium chlorinated compounds were contaminated by iron and manganese chlorides. Complete extraction of the niobium and tantalum pentoxide was achieved during the carbochlorination of the high grade concentrate at 300 and 500 "C, respectively. While chlorination of this concentrate at 1000 "C, allowed to the volatilization of about 60 and 80 % of Ta205 and Nb205. In both cases, condensates were composed of almost pure tantalum and niobium chlorinated compounds. The results demonstrate the advantages of the lixivialion based on the "pseudo- structure" of the raw tin slag to obtain the high grade concentrate. The conclusions of this work suggest that the carbochlorination of the high grade concentrate is an efficient process for the extraction of refractory elements from tin slag.

Jan 1, 1993

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering materiaL Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to dcsign new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass speetrometer.

Jan 1, 2003

By M. Misra

The bacterium?Mvcobacterium Phlei has a demonstrated potential to be used for the flocculation of a variety of finely divided minerals. The microorganism possesses both hydrophobic surface and high negatively electrostatic charge. It can adhere to many mineral surfaces ?if the charge and hydrophobic interaction? between the microorganism and the minerals are favorable to adhesion. Experimental results showed that the dolomitic phosphate slime from Florida and fine hematite can be :readily flocculated from dilute suspension.. In the case of dolomitic phosphate slime, a consolidated sediment containing 24'-25 weight% :solids can be obtained from .a dilute slurry .in a short time. Sediments obtained from hematite flocculation are rather massive and more .consolidated than phosphate slime. Mycobacterium Phlei has a specificity for selective flocculation of hydrophobic fine coal particles from pyrite and ash containing minerals. Because of mutual hydrophobic interaction of coal and Mycobacterium Phlei, it was noticed that coal particles appear to be strongly held in the aggregate by adhesion or bridging of bacteria. However, Mycobacterium Phlei is not a good flocculant for either associated pyrite or ash present in coal.

Jan 1, 1991

By P. M. Swash

The determination of the heavy minerals in beach sand samples is highly dependent on the preparation technique used. In this paper a simple reproducible method for the quantification of "recoverable" ilmenite, zircon, rutile and leucoxene by magnetic separation, is described. The procedure recommended yields information relevant to the metallurgical processing of the ore rather than to the total heavy minerals present in the samples. Finally the determination of mineral reserve estimations and grade assessments is greatly facilitated when this "mineral assay" method is employed. An assortment of other mineralogical methods are described including SEM, EMPA, XRD, XRF, Image analysis, Mossbauer. clerici and perm roll separations. The methods are briefly examined and the practical information that can be gained by using such techniques are reviewed. Experience has shown that an understanding of the relationship between the physical and chemical properties of the heavy minerals can contribute to the prediction of mineral particle behaviour. Such information may ultimately help reduce the prospect evaluation period and minimise expenditure on metallurgical testwork.

Jan 1, 1991

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the process, to the subsequent cleaning of the gas. and to the use of the heat extracted from the gas. The method of reducing the effect of acidic sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms?are discussed. The development of indirect recuperators using air, water or steam cooling, made possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process? conditions".

Jan 1, 1992

By Entov Vladimir M., Gilmer R. Burgos, Andreas N. Alexandrou

"Processing of metal alloys in their mushy state represents a new trend in metal processing. As part of this process, known also as thixocasting, a specially prepared slurry at a temperature in the mushy region is injected into a die. Parts produced using this technology offer better mechanical properties than those produced by casting, and comparable to those of forged alloys.In thixocasting, semisolid slurries are highly concentrated suspensions of rounded rosette-like crystals in eutectic liquid. The mechanical behavior of the slurry is determined by the structure and properties of the skeleton formed by the alpha phase particles. The skeleton structure is almost never at equilibrium, and its evolution is, governed by a number of kinetic phenomena of different c11'aracteristic time-scales. Therefore, the skeleton structure depends on the mechanical and thermal history of the material. As a result of these kinetic processes, the rheological properties of the material, such as effective viscosity and yield stress, decrease with structure breakdown, and increase with its development. In the present investigation, the behavior of semisolid slurries during processing is modeled using the conservation equations, and a Herschel-Bulkley fluid model. The rheological parameters are assumed to be functions of the solid volume fraction, and of a structural parameter that changes with processing history. The evolution of the structural parameter is described by a first order kinetic differential equation that relates the rate of build-up and break-down of the solid"

Jan 1, 2000

By Andreas H. Vassiliou

Organic materials are major constituents of the ore in several uranium deposits. Some of these deposits have been described as "urano-organic" because, the organic materials are believed to have provided the dominant control for the accumulation and deposition of uranium and are directly and intimately intermingled with the uranium. The nature of these urano-organic deposits has been problematic in terms of (a) the origin of the associated organic materials and (b) the specific form of' occurrence of uranium. The organic materials in urano-organic deposits have been genetically related to both coal and petroleum or their progenitors or deriva-tives. Analytical data presented here (infrared, chemical. D.T.A.) suggest that coaliferous materials or related plant derivatives represent the main source of the organic fractions in practically all major urano-organic ores analyzed from the Colorado Plateau and other areas. Recognition of the specific form of occurrence of uranium in urano-organic deposits has been problematic mainly because the uranium is usually in an extremely fine-grained and disseminated state in the organic matrix. Electron microprobe and X-ray diffraction analyses presented here show that fine-grained uranium minerals, specifically uraninite or coffinite. are disseminated in the organic matrix as the predominant form of uranium in most major deposits; however. the presence of true organo-uranium compounds is also suggested for some deposits.

Jan 1, 1981

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By Itavahn Alves da Silva, Jose Dimas de Arruda, Amanda Aparecida Fátima Arruda, da Silva de Souza, Carlos Antonio da Silva, Varadarajan Seshadri, Samuel

The knowledge of the flow field inside a continuous casting mold is essential to improve operational efficiency of the process and also to achieve better inclusion control. Physical modeling, PIV technique and CFD have been employed to assess the velocity distribution in the metal- slag interface region in a slab mold. The analysis of results shows how higher casting velocity and lower immersion depth of submerged nozzle can lead to higher turbulence in the slag-metal interface. The effects of density difference between slag and metal and interfacial tension between the phases have been highlighted.

Jan 1, 2016

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By Hsin H. Huang

Equilibrium calculational software programs can be effectively utilized to model the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation on extraction and recovery processes. Illustrative examples using the calculational program ST ABCAL for the creation of diagrams such as EwpH, activity or concentration-pH, and activity or concentration-EH are presented to demonstrate the fundamental characteristics of real hydrometallurgical mercury dissolution and recovery processes. An industrial application will include leaching of mercury from K 106 mercury sulfide waste and solution purification by iron cementation.

Jan 1, 2003

By Yang Hong-ying, Yu Juan

Electrochemical behavior of natural chalcopyrite in electrolyte solution at pH value of 6.97 was studied by cyclic voltammetry, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The results showed that the electrochemical processes occurred on electrode surface were controlled mainly by the growth of sulfur species at lower applied potentials (<0.35Vvs.SHE), and the oxidative dissolution of sulfur species and the hydroxylation of iron at higher applied potential (>0.45V). The EIS spectra of oxide product layers could be illustrated by the equivalent circuit of Re(QdlRct(QfRf)), and the degree of hydrophilicity for chalcopyrite was higher when the value of charge transfer resistance Rct. was greater. The optimum potential range for the floatation of chalcopyrite in collectorless solution at pH value of 6.97 was between OCP (0.165V) and 0.35V.`

Jan 1, 2015

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothcrmic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperarure rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (>10 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By Oszkar Bíró, Peter Mittag, Bernhard Aigner, Stefan Pirkeri, Philipp Glttleri

"This paper considers CFD modeling of processing and melting of small metallic particles by means of electrical heating. The particles fall continuously onto a liquid metal bath which is heated by an electric arc. After melting of the particles liquid metal is tapped.The charging behavior of the particles in the supply unit as well as in the reactor freeboard is studied by means of Euler-Euler granular simulations. The flow situation in the metal bath due to gas injection and magnetic fields is calculated by combining Navier-Stokes and Maxwell solvers. The macroscopic melting process occurring during the continuous charging of the particles is studied by kinetic laws for melting reactions. The temperature field is evaluated by balancing heat sources due to Joule's heating and heat losses due to latent heat of melting as well as convection and radiation.As a result of these simulations the fully three-dimensional flow fields of particles and gas in the atmosphere is obtained. Furthermore the flow field as well as the magnetic field in the metal bath can be studied. As a main result the three-dimensional concentration field of the still unsolved particles in the liquid metal can be evaluated.IntroductionIn this paper a metallurgical process for melting small iron particles is investigated by means of CFD-simulations. In a first process step the preheated and already mostly reduced iron particles fall continuously into the reactor through a vertical tube mounted at the lid of the furnace. In a second step the particles are melted in the liquid metal bath. Meanwhile the melt is heated by electric arcs to provide the heat needed for melting the incoming particles.In Figure I a sketch of the geometry setup considered in this paper is provided. The particles fall from a height of approximately 12 meters onto the bath surface in the center of the furnace. The melt is heated by electric arcs that are placed symmetrically around the center axis."

Jan 1, 2001