Search Documents

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By Ying-Chu Hoh

The extraction of cerium(IV) by valence change with two-phase electrolysis was studied experimentally. The results show that the electro-oxidation extraction depends mainly on the distribution of the solute between the two phases, the reaction on the electrode surface and the diffusion of the reactant and product between the electrode and aqueous interphases. The effects of various parameters on cerium extraction were also studied. The selected parameters were background current, catholyte acidity, agitation speed, operation current and voltage and surfactant addition. The electro-oxidation extraction mechanism can be divided into eight steps. In addition, Wee the rate of extraction is quite fast, the percentage extraction Ce+4 can be taken as an index to show the conversion rate of Ce+3 J to Ce+4.

Jan 1, 1989

By Robert W. Bartlett

"Economic and other factors, mostly outside of metallurgy, that strongly influence applied research, development and especially successful commercial adoption of new processes for producing primary metals and other commodity materials are reviewed. These factors, which can be both positive and negative in their influence, are often too lightly regarded in the research planning stage. They include continuing imperatives that have long influenced new process development as well as more recent trends. Both are discussed. Nearly all new materials eventually become commodities--products made to standard specifications with no producer control over price. Success requires being a low cost producer on a world wide basis. Composites and other complex material assemblages are unlikely to escape this fate as they mature.INTRODUCTIONThe adoption of new processes, beginning with research and development, for primary metals and other commodity materials is particularly difficult because each new process must supplant an existing process that is already being used commercially. There are many requirements besides technical innovation and cost superiority that must be met by the new process. Consequently, few innovations make it all the way from the research laboratory to commercial success.This paper discusses some of the factors that influence success in developing new processes for primary metals and commodity materials, based on the authors experience as a research metallurgist and industrial research manager. It begins with some of the factors that are always present and constrain successful process research and development, and proceeds to current trends that are expected to continue long enough to influence processes in the year 2000. Many of these trends are contradictory in their effect on new process development, and the future remains uncertain.The prevailing importance of these trends will vary with the material, process concept and other factors intrinsic to each case. Nevertheless, an awareness of these influences can help to avoid some of the R&D pitfalls and dead ends. Such awareness is deemed to be a necessary condition to avoid failure when commercial adoption of a new process is the goal."

Jan 1, 1988

By Erwin Flender, Preben N. Hansen, Peter R. Sahm

"Until now FDM-Techniques have been widely used for Modeling Solidification Processes in Castings. Often a rigid, regular type of enmeshment (cubes, , --) have been used. This has the advantage of low CPU-costs, but the disadvantage of a zig-zag presentation of the interface between the casting and the mold. The last point is the reason why FEM-Techniques, giving the possibility of a true presentation of the shape in the enmeshment, are increasingly used. The disadvantage is the high CPU-costs. In this paper, a technique is presented, which uses the FDM-Mesh with the zig-zag presentation of shape and ADI-Algorithms to calculate temperatures and gradients. The new idea is that the calculated parameters are not presented related to the mesh in which they are calculated, but displayed using the true shape of the casting. Such an advantage of both low CPU-costs and shape correct presentation of the calculated results are achieved. IntroductionThe main reason for using a regular type of enmeshment is that it gives the possibility, via ADI-Algorithms, of obtaining a very fast FDM-Technique. The technique presented by P.R. Sahm and P. N. Hansen (1984), and also used by E. Flender (1985), is numerically so stable that average time steps, at least 200 times larger than the limit given by the explicit FDM-Technique, can be applied. To obtain reasonably good results, average time steps in the range of 20 to 50 times the explicit limit seems to be applicable. It should be pointed out,however, that FDM-Techniques can be used on arbitrary nets, the disadvantages being the same as for the FEM-Techniques. This has, among others, been discussed by P.R. Sahm and P.N. Hansen (1984)."

Jan 1, 1986

By Mark Samonds

"Manufacturing processes which involve liquid to solid and solid state transformations in metals encompass a wide variety of physical phenomena. The past twenty years have seen a steady evolution in the complexity and scope of numerical models of these processes, beginning with thermal analyses without phase change. Recently, a few software packages have become available which have true multi-physics capabilities. This permits the treatment of thermal, fluids, stress, electromagnetic, chemical reaction and microstructure development aspects altogether in a fully coupled simulation. This paper will consider various aspects of these types of models.Coupled thermal and fluid flow analyses of continuous castings have been around for fifteen years. Coupled thermal and free surface fluid flow simulations of shape castings have been available for ten years, including view factor radiation models for investment castings. Only recently, however, have fully coupled thermal, fluid, and stress analyses become practical. This implies the reverse coupling of the mechanical deformations to the solution of the energy and momentum equations through modification to the interface heat transfer coefficients and the fluid domain geometry. This has been implemented with a combined eulerian-lagrangian finite element method. Appropriate mechanical constitutive models will also be discussed.Many types of defects need to be predicted in casting processes. Those related to stress include hot tearing, hot cracking, part distortion, and thermal fatigue in dies. Macroporosity, microporosity, and microsegregation are determined by the solidification behavior and microstructure development in a casting. In particular, microporosity is influenced by dissolved gases, the morphology of the mushy zone, the liquid to solid density change, and the local pressure conditions. Macrosegregation is caused by the partitioning of solutes during. solidification and subsequent thermo-solutal convection. An additional transport equation is required for each solute that is being tracked. Computational thermodynamics is being incorporated into these types of analyses to determine transformation temperatures, partition coefficients, densities, and enthalpies. In combination, the microstructure and microporosity models can frequently predict a variety of mechanical models, such as yield strength, tensile strength, and elongation."

Jan 1, 2001

By S. Kawamura, H. Inoue, Y. Maeda, H. Ohike

Kosaka smelter is a copper smelter located in Akita Prefecture in the northern part of Japan. It has treated complex sulfide concentrates for a long time. Recently, in addition to metal production from ores, the company has been working on the recycling of metals by using this metallurgical technology. Metals recovered are primarily gold, silver, palladium, copper and lead from copper scraps, electronic board scraps, silver oxide batteries, spent lead acid batteries, semiconductor chips, cellular phones, and automotive emissions catalyst. In particular, electronic board scraps and cellular phones can be valuable raw materials. These electronic scraps are fed into the flash smelting furnace after size reduction in a shredder that was introduced in 1999. Due to the growing demand for personal computers and cellular phones, the amount of electronic board scraps available for recycling increased. At present, these secondary materials are good raw materials for Kosaka smelter since the smelter is already used to dealing with complex raw materials. The recycled metals account for up between 5 and 20 percent of the total production at Kosaka Smelter. In particular, over 90 percent of the palladium in the secondary materials can be recovered.

Jan 1, 2000

By R. D. Prengaman

Lead usage in paint, anti-knock gasoline additives, pipes, seals, and solder has declined markedly over the past 30 years. Products utilizing the unique properties of lead and its ability to be recycled have survived and grown. These products include shielding, glass (particularly TV and computer screens), sheet for roofing, stabilizers for PVC, insoluble anodes for metal production, electronic solders and lead acid batteries. With the loss of markets many companies have decreased lead product development efforts. Much of the patent lead materials development is devoted to lead acid batteries. In the past 25 years, the automobile battery has been almost doubled in power and reduced in weight, leading to a nearly three-fold increase in performance. Corrosion-resistant lead alloys and improved battery designs have made battery lead usage more efficient. The same corrosion-resistant battery alloys are utilized to increase the life of electrowinning anodes. The challenge for lead product development is not only to maintain and improve the existing lead products, but also to develop the growing lead acid battery market for telecommunications, uninterruptive power sources, remote area power, hybrid and electric vehicles. Lead

Jan 1, 2000

By Michael Meyer

In the past shredder fluff was discarded in landfills, but shrinking landfill space and the partly hazardous content of the fluff as well as its caloric value, all resulted in efforts to turn this waste problem into a an energy resource. In order to produce a fuel, the inorganic compounds have to be removed. Extensive analyses and particle size measurements were made on fluff from various shredder. For optimal separation all particles are reduced to a uniform, relatively small size. In a subsequent combined - screening and air classification - process, successful separation into organic and inorganic fractions is achieved. The inorganic fraction is treated in a heavy media or an eddy-current separator to recover the valuable metals, while the organic fraction is now suitable for thermal processing, such as fluidized bed gasification and using the resulting carbon as a chemical reagent.

Jan 1, 1995

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999

By K. Rajani Kanth

Environmental problem is the major concern for any industry and there is a great need to that along green lines. Sangam Dairy being one of the most famous and wide spread Dairies in India, produces wide spectrum of milk products. The BOD levels of effluent water of this industry with MIF treatment were found to be around 100 ppm. Lot of research has been expended in the past to bring down the BOD levels to bare minimum. The main objective of the present study is to minimize the BOD level to the required level stipulated by environmental standards by employing various seeding materials. For this purpose microbes like Bacillus Subtiles, Pseudomonas, Aspergillas, Staphylococcus, and Pencilium have been employed and BOD levels were analyzed. Various Reagents, solutions with different dilution levels have been successfully prepared. Initial and final Dissolved Oxygen levels were determined before and after incubation. From the DO data, BOD was evaluated for all samples and comparison analysis of various seeding material was carried to suggest the efficient seeding material for the ETP plant. In the process, solutions of different dilutions have been prepared using difficult reagents. These samples are treated with above mentioned microbes and BOD levels are estimated. It has been observed that staphylococcus and Pseudomonas proved to be the best seeding materials. When there microbes have employed BOD levels fall to less than 10 and 20 ppm respectively

Jan 1, 2006

By A. R. G. Azevedo, G. C. Xavier

"This work has for objective to identify the soil of the neighborhood Codin located in a lacking area of the urban nucleus of the district of Campos dos Goytacazes - RJ, after the identification the best line was determined for the production of soil-cement blocks. In this area it happens habitational deficit and precarious constructions are also verified. The use of soil cement blocks is considered a cheaper constructive method than the conventional (ceramic block or of concrete), because one of the components of the raw material is abundant (the soil) and the constructions can be erect with certain easiness for collective effort regime. Samples of soil of this area were collected for they be characterized with relationship to the physical and chemical characteristics, with I aid of GPS the community's location it was registered. Identified the soil type, the work began the study of lines they to make possible your use in an economical and safe way. For that were made drained blocks in the format 19,5x10x5 cm, with lines containing the addition of 5% and 10% of cement in volume, and as parameter of quality the absorption of water and the resistance to the compression were measured, following the Norms of ABNT.IntroductionWe know that the use of the soil by the humanity come from the antiquity. And ifs confirmed by the archaeology places of the old civilizations of the word. The most remote constructions date from 10.000 years old in Jericoh, in the Jordan River Valley. This work became more intensive at 3.000 B.C. (Before Christ), by people who lived in those valleys with mood areas, a lot of clay and washed by the rivers.Almost all the sectors of engineering of soils choose the stability to use the local soil. Although, artificially treated, offers more economical advantages.The stability of a soil consist of endow it of the condition to resist the deformations and ruptures during the period that it is being used, because these characteristics are necessary in any construction.The application of the natural soil only is possible in places that they are of good quality and attend to the requirements of engineering to the type of previewed application. The granulemeter correction and the chemical stability include cases of inappropriate soils areas, turning the soil able to be used as construction material. Among the stability agents, usually added to the soil for stability ends, the cement is indicated."

Jan 1, 2013

By P. Stantke

In recent years the CollaMat process has been used successfully worldwide in a number of copper electrorefining tankhouses as an instrument for measuring the glue concentration and optimizing cathode quality. Owing to its measuring principles the CollaMat can be used not just for measuring the concentration of active glue but also the activity of other substances, which have an impact similar to glue on the copper deposition. In SX-EW plants guar is frequently used instead of glue as a levelling additive. In our laboratory the effect (activity) and the decomposition rate of guar in copper electrolyte was examined. As expected, the results show that guar has an effect similar to glue on the copper deposition. However, at the same temperature, a greater quantity of guar is required to achieve the same results. As with glue, the decomposition rate (due to hydrolysis) of guar is strongly dependent on the temperature. Therefore, in practice, its on-line monitoring is necessary to guarantee the same guar activity at any time.

Jan 1, 1999

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF's. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By Henry Freiser

For the last several years, a systematic investigation of the equilibrium extraction behavior of selective tervalent lanthanides with representative chelating extractions of a variety of chelating agent families has been undertaken for the purpose of learning how to obtain chelating extractants of improved selectivity for separating individual lanthanide ions. The equilibrium extraction data (expressed as log Kex) for each reagent system are linearly related to the reciprocal ionic radius of the tervalent lanthanide ions. The role of adduct formation, steric hindrance, as well as the nature of the bonding atom in the chelate ring, represent some of the factors affecting selectivity arising out of our database of over 200 individual extraction systems, which will be discussed.

Jan 1, 1989

By R. Chiarizia

Third phase formation, i.e., the splitting of the organic phase in two layers, is a common feature observed, under conditions of high loading, for many solvent extraction systems of both analytical and industrial interest. Although this phenomenon has been investigated in a large number of works, a structural and physico-chemical description is still lacking. In this work, small-angle neutron scattering (SANS) data for the tri-n-butylphosphate (TBP)-n-octane,Th(NO3)4-HNO3 solvent extraction system have been interpreted using the Baxter model for hard-spheres with surface adhesion. The increase in scattering intensity in the low Q range, observed when increasing amounts of HNO3 and/or Th(NO3)4 are introduced into the organic phase, has been interpreted as arising from interactions between small reverse micelles containing three TBP molecules plus solutes in their polar core. This intermicellar attraction, under appropriate conditions, leads to third phase formation.

Jan 1, 2003

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By Jong-Shin Chang

The Onsan smelter has tried to do various activities to decrease operation costs. With several expansion projects, the Onsan smelter has aimed at not only a quantitative growth but also qualitative growth through efforts improving operations equipment and processes. Activities to reduce operation costs have been one of those efforts. In particular, the energy cost of operation has been a main target for reduction. The activities to save energy have been carried out in two ways. One is to recover and utilize waste heat as much as possible and another is to replace existing equipment and processes with more energy-efficient ones. This paper reviews recent improvements and future plans for energy saving activities at the Onsan smelter.

Jan 1, 2006

By David B. George

In spite of the many well-known problems inherent in Pierce-Smith converting, it remains the dominant copper converting process. Continuous copper converting and direct concentrate to blister smelting have been commercially available for over 25 years and now produce approximately 15% of copper smelter production. The two fully commercialized continuous converting processes, Mitsubishi MI Process and Kennecott-Outokumpu Flash Converting, and several emerging converting processes are reviewed with view of their potential, limitations, and environmental performance. Some myths regarding these technologies and Peirce-Smith converting are also challenged.

Jan 1, 2002

By F. M. Doyle, K. Sreenivasarao

Copper and cadmium metal has been recovered from dilute (3 X 10-4 mol/dm3 ) chloride solutions by ion flotation with dodecysulfate, followed by electrolysis. This approach should facilitate treatment of effluents too dilute for effective direct electrolysis. . The adsorption density of metal dodecylsulfate complexes on bubble surfaces was estimated from surface, tension data, and compared well with experimentally-observed metal removal kinetics, and ultimate recoveries. Copper and cadmium were recovered by electrolyzing the foamate, using steel wool cathodes and a graphite anode. The stability constants of the copper and cadmium dodecysulfate complexes are estimated, and used to analyze the thermodynamics of electrolysis. Dodecysulfate was unaffected by the electrolysis process, and hence could be recycled to ion flotation. A conceptual flowsheet for an overall effluent-treatment process is presented.

Jan 1, 1997

By Gustavo A. Munoz

Activated carbons owe their adsorption capacities to their extensively developed pore network structure. As a result, these adsorbents generally exhibit high specific surface areas. Currently, granular activated carbons produced from coconut shells are traditionally used for gold recovery by adsorption from cyanide leaching solutions. Magnetic activated carbons (MACs) for gold recovery from cyanide solutions produced from sources other than coconut shells have been developed at the University of Utah by mixing a magnetic precursor with a carbon source, and treating the mixture under controlled conditions of temperature and gas phase composition. The pore size distribution of the activated carbons is dependent on the degree of activation, among other factors. The significance of the MAC pore size distribution on gold adsorption kinetics and gold adsorption capacity is presented.

Jan 1, 2003