Search Documents

By N. Menad

The formation of the dioxins can be dependent on the quantities of carbon, hydrogen, chlorine and oxygen present in a given system, as well as on parameters such as temperature and pressure. Inadequate supply of combustion air ( incomplete oxidation ), low combustion temperatures ( incomplete combustion ), and insufficient turbulence in the combustion are factors which can favour their formation. Dioxins were produced also calatytically from chlorinated phenol precursors, non-chlorinated compounds that were chemically, and reaction of phenol with inorganic chloride. In this paper different precursors such as combination of C, H, 0, Cl, rapid formation/combustion intermediates and routes to PCDFs are reviewed, and the influence of PVC amount on the formation of these isomers is discussed.

Jan 1, 2000

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By M. Y. Mohassab-Ahmed

In an effort to develop a novel flash ironmaking process, the chemistry of selected slags was investigated. In different ironmaking processes, the molten bath (iron-slag bath) is expected to be in contact with gas atmospheres of H2/H2O, CO/CO2/H2/H2O, and CO/CO2. The latter was investigated to allow comparison with the blast-furnace conditions. The slag composition was selected to resemble that of the blast furnace with CaO/SiO2 in the range 0.8 to 1.4. The temperature range was 1550 to 1650°C. The oxygen partial pressure was maintained in the range 10-10 to10-9 atm. The effect of water vapor on the chemistry of the slag as well as the equilibrium reactions involving the slag has been studied for the first time. H2O dramatically affects the chemistry of the slag and strongly affect the phase equilibria in the slag as well as the equilibrium distribution of elements between slag and molten metal.

Jan 1, 2014

By Edgar E. Vidal

The deposition of ceramic materials onto substrates is of special interest in the development of surface related technologies. Research interest has been placed on using thermal plasma as the deposition method, specifically inductively coupled plasmas. Many different modifications to the same basic principle of deposition have been performed through out the materials research community. Such a technique may have many advantages over more conventional techniques, such as high deposition rates, high surface area coverage, clean energy source, no contamination from electrodes and operation near atmospheric pressures. Materials deposited vary from simple oxide systems like TiO2 to more complex structures like ternary oxides and nitrides. This paper reviews recent developments relative to the inductively coupled plasma deposition of thin films.

Jan 1, 2003

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By Kuniaki Murase, Tetsuji Hirato, Koji Nitta, Yasuhiro Awakura

"The redox behavior of copper species in an ""ammonium imide"" room temperature molten salt was examined in order to clarify the applicability of the salt to the electroplating media of various metals. Trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)- amide (TMHA-Tf2N), having an electrochemical window of 5.6 V (50 °C), and corresponding copper(II) salt were synthesized. In TMHA-Tf2N media monovalent copper ion, Cu(I), was stable and Cu metal was oxidized, or corroded, in the presence of Cu(II) species. Cathodic electrodeposition of copper metal and anodic dissolution of it were, thus, one-electron reaction and their current efficiencies were almost 100%.IntroductionElectrodeposition of metals from aqueous solutions is an important soft process for manufacturing thin-film materials, surface finishing, and extractive metallurgy. However, the electrodeposition of base metals, such as zinc, chromium, and nickel, from aqueous media inevitably accompanies hydrogen evolution, which lowers the cathodic current efficiency of metal deposition. Since the electrodeposition of aluminium, titanium, and rare earths from aqueous media is actually impossible due to their largely negative redox potentials, nonaqueous media such as aprotic organic solvent and high-temperature molten salts have been employed for the electrodeposition of these metals. Room temperature molten salts (RTMS),1, 2) or room temperature ionic liquids, have also been developed as a promising electrolytes for the electrodeposition of base metals. In this field, chloroaluminates of alkylpyridinium or alkylimidazolium cation have been well investigated for aluminium3) or alluminium-alloy4-5) electroplating media. On the other hand, in order to avoid high hygroscopicity arising from the use of aluminium chloride, attempts have been made to combine the alkylimidazolium cations with fluorine-containing hydrophobic anions, e.g. BF4-,6) CF3SO3- (TfO-),7) (CF3SO2)2N- (Tf2N-),8) and H(HF)n-ions,9) and investigated for electrodeposition media.'°) Recently, a new series of RTMS consisting of tetraalkylammonium cations and Tf2N- anion, sometimes abbreviated as TFSI- anion, was found independently by MacFarlane et al.11, 12) and Matsumoto et al. 13) This type of RTMS, which is commonly named ""ammoniumimide"" salt, has a wide electrochemical window of ca. 5 V and, thus, the RTMS seems to be suited for practical application as a solvent for the electrodeposition process. In this paper, we report the electrochemical behavior of copper species in an ammoniumimide RTMS, trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)amide (TMHA-Tf2N)."

Jan 1, 2000

By Jim Sundal

Primary steel manufacturers using electric arc furnaces generate one of the largest hazardous waste streams nationwide. The waste stream, known as electric arc furnace dust, is a listed hazardous waste with the designation K061. Oregon Steel Mills, Inc., (OSM) of Portland, Oregon, has implemented a process known as Glassificationn, which uses KO61 as an ingredient in an onsite recycling process. Because OSM was able to demonstrate that the Glassificationm recycling process beneficially uses all toxic constituents in the electric arc furnace dust and that the recycling process produces marketable products, the process is not subject to Resource Conservation and Recovery Act (RCRA) permit requirements. The marketable products manufactured using Glassificationn include roofing granules, ceramic glazes and colorants, abrasive blasting media and, more recently, synthetic slag fluidizers. The purpose of this paper is to identify the regulatory issues for recycling hazardous waste and demonstrate that OSM glass frit is effective as a slag fluidizer in primary steel manufacturing.

Jan 1, 1994

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By Autumn Fjeld

The filling and solidification of an industrial scale composite casting has been simulated to investigate the re-melting of the outer shell material during casting. Production of a composite requires a two-step casting process which includes centrifugal casting of a hard outer shell material and subsequent conventional ingot casting of a tough core material into the shell-mold assembly. During casting of the core, a thin layer of the shell material re-melts and mixes with the core material producing a bonding layer of intermediate composition. The present numerical model employs the volume of fluid method and an enthalpy-porosity technique to couple the filling of the core material and re-melting of the shell material. The interface between the two materials is tracked and can be used as a guide to examine the extent of melting and, to some degree, mixing of the two fluids and species diffusion.

Jan 1, 2008

By Emilia Visileanu, Eftalea Carpus

"Ecological economic policy shall be understood as the sum of political, economical and environmental measurements aimed at the entire economy dematerialization and the dematerialization shall be ""imposed"" since the designing stage of goods and services"". European textile and clothing industry with a long leading tradition in terms of innovation, fashion and creativity, continues to be one of Europe's major industrial sectors. Textile industry affects the environment by high consumption of water, energy and chemicals, as well as by the large amount of waste it generates as a result of using a large number of chemicals and technological processes.Textile waste prevention, reduction and ecological exploitation require the implementation of new management and education tools.Introduction“Europe must learn from the experience of global economic and financial crisis ""- this was the conclusion of the European Commission that has elaborated a ten-year strategy designed to reinvigorate the economy and make possible a growth which is ""intelligent, sustainable and favorable to inclusion"", by a better coordination of national and European policies.Adapting infrastructure and logistics that encourage the marketing of ""sustainable"", ""fair traded"" and ""green"" products as well as other special „green” products will facilitate the movement towards dematerialization and eco-efficiency among producers."

Jan 1, 2012

By S. G. Kumar

The performance of nickel based high temperature materials is directly related to their microstructure, which is controlled by the various processing steps. Nickel base alloys are melted and refined by a variety of processes that include Vacuum Induction Melting (VIM), Vacuum Arc Remelting (VAR) and Electroslag Remelting (ESR). The limitation of VIM is that the metallrefractory reactions lead to the disintegration of the crucible and hence contamination of the product due to macrosegregation. This macrosegregation is alleviated to some extent by controlling the solidification in VAR. The main attraction of ESR is its ability to produce a clean product by controlling the deleterious inclusions. In recent years Electron Beam Melting (EBM) is emerging as an alternative to the VIM, VAR and ESR. This paper reviews the current status of these processes and outlines the scope for further improvements in the processing technology.

Jan 1, 1993

By Mansoor Barati

The present paper is based on a term project for final year undergraduate students, requiring them to evaluate a process for producing silicon from rice husk. The traditional method for production of silicon involves carbothermal reduction of quartz in electric arc furnaces at temperatures exceeding 2000 °C. The technology consumes a considerable amount of electrical energy as well as fossil fuels, resulting in significant CO2 emissions. A flowsheet for production of silicon metal from rice husk is laid out in this paper. The technology will consist of combustors, which will generate steam using the rice husk biomass, power generator, and electric furnace for reduction of the rice husk. Materials and energy balance calculations presented here indicate that such process can be operated independent of external electricity.

Jan 1, 2014

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,&apos;) by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By H. Y. Sohn, S. PalDey

"Fine particles of nickel aluminides and Ni4Mo were synthesized by reducing mixtures of, respectively, A1Cl3 + NiC12 and NiC12 + MoC12 vapors with hydrogen. Though thermodynamically favorable, the coreduction of NiC12 and A1Cl3 by H2 to form Ni3Al did not readily happen experimentally. The addition of a small amount of aluminum vapor was needed to initiate the coreduction reaction. The product particles as observed by TEM were very fine but usually agglomerated. The electron diffraction pattern of particles identified NiAl and NiA13 along with Ni3Al and metallic Ni. The content of Ni3Al was maximized at 52 mol% at 1050°C under the partial pressures ofH2, A1Cl3, and NiC12 at 57, 1.4, and 0.5 kPa, respectively. When a mixture of NiC12 + MoC15 was reduced by hydrogen, Ni4Mo particles with some Ni or Mo particles were obtained, the maximum content of Ni4Mo obtained being 93 mol % . The particle size was in the range of 100 to 200 nm. An Ni4Mo coating of 700 nm thickness on an Ni substrate was also prepared.IntroductionThe search for new high-temperature structural materials has stimulated much research on intermetallic compounds. Nickel aluminides have low densities, relatively high melting points, and good high-temperature strength properties. They show an increase, rather than a decrease, in yield strength with increasing temperature (1). Ni4Mo is also of interest as a high-temperature structural material. The major shortcomings of these intermetallics are their inherent brittleness at room temperature when they are in polycrystalline form. For much the same reason, the conventional casting of intermetallics is difficult. Ingot metallurgy and powder metallurgy are two other processing techniques. The first technique is quite energy consuming. In powder metallurgy, the powders of metals and alloys are consolidated in near net shape and then subjected to secondary processing. It would, therefore, be advantageous if intermetallic compounds can be produced in fine powder form from inexpensive raw materials, using less energy."

Jan 1, 1998