Search Documents

By Shane Andrews, Gustavo Vasquez, S. K. Varma

"The effect of solutionizing time on the corrosive wear behavior of 2014 aluminum alloy has been studied using the impact and continuous mode of scratching techniques. The transient currents (TC) evolved during the scratching of the alloy shows a linear dependence between the TC and the solutionizing time. Higher TC values at longer solutionizing time may be associated with the changes in the concentration of quenched-in vacancies, grain sizes and dislocations generated during scratching. These factors can either create (a) anodic sites or (b) pitting corrosion resulting in the generation of transient currents. The results have been compared with the similar study carried out for 6061 aluminum alloys. This 6061 aluminum alloy shows similar behavior but the rate of TC generation per unit solutionizing time is much lower than 2014 aluminum alloy. The morphological changes in the impact scratches and the TEM investigation in the scratch have been presented in this paper.IntroductionThe technique of studying corrosive wear of composites of 6061 aluminum in the monolithic and reinforced forms has been reported in the literature [1]. Two modes of scratching, consisting of impact and continuous, in a corrosive environment indicate that the composites, containing 0.10 and 0.20 volume fractions of alumina particles (VFAP), have higher corrosive wear rates than the monolith. A graph between the transient current (TC) generated during the impact scratching as a function of solutionizing time at 540°C indicates linear relationship between them. A similar slopes for the composites were observed and the TC values were less for the composite containing lesser VFAP."

Jan 1, 1998

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By John L. Watson

The dewatering of steel industry waste sludges prior to discard or recycling often presents significant problems due to the fineness of the sludge particles, which may blind the filter medium and/or produce a cake with limited porosity, Several steel plant wastes, such as sludges from BOF and EAF gas cleaning operations exhibit not only a very fine particle size, but also some degree of magnetic character, A novel process has been developed to utilize the magnetic character of such sludges to enhance dewatering through a multi-force operation involving magnetic, chemical and vacuum forces, The process consists essentially of undertaking vacuum filtration of a flocculated sludge in a magnetic field, This is achieved by installing a permanent magnetic in a fixed position on the axis of a vacuum drum filter, thus effecting filtration of magnetic and non- magnetic particles, bound together in flocs, in a magnetic field, Previous tests using a modified laboratory vacuum drum filter treating artificial (magnetite) and industry waste (BF sludge) feeds have demonstrated that filtration capacity may be enhanced significantly with increases of up to 3000/0, An explanation of the mechanisms associated with the enhanced filtration was not obvious, and this research was undertaken to permit the cake formation in the magnetic field to be monitored to provide an insight into the manner in which particles agglomerate to form the cake. These tests revealed that the magnetic field caused magnetic particles to be aligned perpendicular to the filter surface and to form channels through which filtrate could freely pass thus increasing capacity, The effects of various magnetic fields and field strengths on the filtration process were also investigated. A simple computer model was constructed to demonstrate the proposed theory of multi-force dewatering, The model output graphically illustrated the suggested mechanism and confirmed the enhanced capacity of the novel dewatering process,

Jan 1, 1996

By K. Mansfield

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluorides along with traces of cyanide. In 1995, Portland Aluminium undertook the investment of AUD$26,400,000 to construct a Research and Development processing facility at Portland, Victoria, Australia, to treat SPL. Extensive research, development and design were carried out over 5 years prior to the investment decision. This study led Portland Aluminium to install an Ausmelt pyrometallurgical furnace to combust and melt the SPL producing a hydrogen fluoride (HF) laden gas, which was cooled and then converted to aluminium fluoride (AlF3). Both the cooling and AIF3 manufacture were processes developed by Portland Aluminium. Many commissioning, equipment reliability and process problems have been encountered that had not been experienced in the trials at Ausmelt or in the developmental process for the treatment of the furnace offgases to form AlF3. Designs based on anticipated process expectations have had to be re-engineered by the SPL team to ensure plant and operational success. In June 2001, the installation of the final major component - a slag granulation process - was completed. This has produced a vitrified (glassy) slag that is expected to have leachability qualities acceptable to the Victorian Environment Protection Authority (EPA) to allow commercial end uses of the slag material to be developed. Today (September 2001), the smelter has successfully used the fluoride product, namely 65- 70% AIF3, in aluminium production and the SPL plant has significantly increased throughput with expectations to be at annual design rates of 12,000 tonne of SPL in early 2002. "The Alcoa Portland SPL Process" has been technically developed and is a proven process for the treatment and recovery of valuable components from SPL materials.

Jan 1, 2002

By Michael A. Markowitz, Alok Singh

"Molecular self-assembly of phospholipids and other amphipathic molecules offers a versatile approach to form self-organized microstructures in various morphologies. Stabilization of microstructures in specific morphologies by polymerization renders them useful for practical applications in areas ranging from controlled release technology to template mediated synthesis of metals. Our efforts are focussed on the development of polymerizable biomembranes derived from phospholipids, their properties and utility e.g., as stable templates for studying chemistry at the lipid interface. Polymerized vesicles formed from mixtures of 1,2-bis(tricosa-1 O,12-diynoyl)-sn-glycero-3-phosphocholine, 1, with corresponding lipids having phosphohydroxyethanol,2, or -hydroxypropanol,3, headgroups have been used in electroless metal plating of vesicle surface with gold utilizing selective binding of Pd(NH3)4 2 + to 2 or 3. The surface bound palladium ion served as catalyst for metalization. Metalization of polymerized vesicles constructed from charge neutral diacetylenic phosphocholine,1, did not occur using this process. The headgroup structure of the negatively charged phospholipids and the degree of vesicle polymerization had an effect on the stability of the vesicles after metalization. Vesicles formed from a mixture of 1 with polymerizable diacetylenic phosphatidic acid, nonpolymerizable 1,2- dipalmitoyl phosphohydroxyethanol or 1,2-diacyl phosphohydroxyethanol (from soy lecithin) were not stable to metalization process. The metal coating of the vesicles was examined by electron diffraction and revealed that the gold metal on vesicles was polycrystalline and face centered cubic. The results demonstrate the utility of polymerized synthetic membranes as template for easy and efficient synthesis of nanoparticles. IntroductionPhospholipids, synthetic or natural, provide a simple and straight forward route to construct membranes in a variety of morphologies due to their inherent property of selforganization in the presence of water[1]. Vesicles are closed spherical structures comprised of concentric walls made from lipid bilayers. Vesicles are morphologically simple structures with enormous technological potential. Polymerizable phospholipids prepared by incorporating a polymerizable group in the molecules demonstrate physical properties comparable to their non-polymerizable counterparts and have the added virtue of providing enhanced physical and chemical stability to the membranes[2,3]. The size, shape and properties of the organized assemblies are dependent on the lipid structure and the nature of the aqueous environment[4,5]. The headgroup geometry, surface charge density, and spatial arrangement of the phospholipids are known to affect the surface behavior of the lipid membranes, which is evident through their interaction with other molecular (hormones, antigens, antibodies etc) or lomc species. Since phospholipid headgroup structure and charge can be modified either synthetically or by chemical perturbation of the aqueous medium (e.g., pH or ionic strength), phospholipid membrane surfaces offer a potential for developing novel strategies in those areas which involve the use of molecular reactive sites. One such strategy which could be envisioned explores the use of molecularly engineered phospholipid assemblies to design and prepare template structures to regulate formation of ordered materials [6]."

Jan 1, 1994

By Daniel K. Kim

The charge for the copper refinery is a mixture of anodes produced at San Manuel from BHP source concentrate and copper purchased from external sources. Control of unwanted impurities in the tankhouse - is very important and beneficial. Currently available removal/recovery technologies were reviewed for the control of bismuth and antimony levels in the electrolyte. Recent studies have focused on solvent extraction (SX) technology and generated successful results for the removal and subsequent recovery of bismuth and antimony. The SX system employs the reagent, ACORGA SBX-50, in conjunction with a patented high chloride stripping system. The latter enables recycle of the eluant, avoiding the high costs associated with conventional systems, such as regeneration of resin. Concerns over potential transfer of organics and chloride ion to the electrolyte were readily addressed, solved and demonstrated using conventional, established technology. This paper describes the benefits of electrolyte purification, the flexibility afforded by the SX system, the operational practices necessary for maintaining adequate control of bismuth and antimony impurities in the electrorefining environment and possibilities for future development /exploitation of the Zeneca SX system at the San Manuel refinery.

Jan 1, 1998

By Renato G. Bautista

"The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.IntroductionThe understanding and the elucidation of the mechanism of the rate phenomena for a specific chemical reaction system is of prime importance in the development of a successful chemical process. The development of successful emerging technologies for metals separation will depend on the accurate interpretation of the intrinsic chemical reaction kinetics and the rate of mass transfer of the desired metal species during its separation from the undesirable chemical species. This is the case whether the process application is for separation, concentration, and /or purification.The chemical processes that will be examined in this presentation will include leaching, solvent extraction, membrane separation, precipitation, and electrodeposition."

Jan 1, 1996

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Jian Yang, Hinmi Zheng

"The mode of occurrence of sulfur and mercury in 57 Chinese bituminous coals have been examined using X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), and Zeeman atomic absorption mercury spectrometer. Mercury levels in coal are related to the geographic location of the coals and types of the coals. A synthesis of result indicated that most likely occurrence modes of mercury in high-sulfur and high-mercury coals are in solid solution in pyrite. Our study from 57 coal samples showed that most values of mercury concentration in coal varied from 100 to 1000 ng/g with an average of approximately 500ng/g, and mathematical model about correlation between mercury and sulfur was gained by mathematical statistics. This is apparent that mercury and sulfur vary concomitantly from coal data (table 3) , the high correlation between them in all coals at confidence of 95% ( a=0.05 ) .1. INTRODUCTIONThere contained about one trillion ton abundant coal resources in China. As a leading level of proven coal reserves in the world, the coals mainly distributed in north China and northwest China, especially in Shanxi, Guizhou, Shanxi provinces and Inner-Mongolia autonomous region. At the same time, China has the largest production and consumption of coal, and has the output of coal nearly accounted for 37 percent of the world's production. Coal-fired power plants are the major source of energy generation in China, and the proportion of coal combustion is up to 75 percent in the total energy configuration. Therefore, the mercury pollution caused by coal-fired has become a topic of wide-spread discussions since 1990. The contamination of mercury of human activities accounted for 10 to 30 percent [1], and the mercury emissions of coal-fired flue gas has made the greatest contribution to the pollution of atmosphere[2] In the past 30 years, the global increasing concentration of mercury pollutant in atmosphere maybe result from coal combustion[2]. The mercury emissions caused by coal-burning has become the main reason of China's mercury pollution, and the characteristics of mercury pollution is closely related to China's energy configuration, additionally, the features of mercury pollution have changed from the point pollution in 1970's to diffused pollution today[3]. Mercury can be found in various types of coals, and it is evaporated into gas phase during the combustion process."

Jan 1, 2011

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By Thomas P. Battle

Titanium is the ninth most common element in the Earth's crust, yet only in this century has titanium come into use as an engineering material, particularly in aircraft structures, as the metal, and in pigments, as the dioxide. In this presentation, the metallurgical aspects of processing titanium-containing raw materials will be reviewed. Particular emphasis will be given to the ores and beneficiation techniques which lead to the production of titanium dioxide pigment, which accounts for over 90% of world titanium production.

Jan 1, 1993

By Gordon D. Jarvinen

Polymer Filtration (PF) Is an innovative, selecthle metal removal technology. Chelating, water-soluble polymers are used to selectively bind the desired metal ions and ultrafiltration is used to concentrate the polymer-metal complex producing a permeate with low levels of the targeted metal ion. When applied to the treatment of, Industrial metal-bearing aqueous process streams, the permeate water can often be reused within the process and the metal ions reclaimed. This technology is applicable to many types of industrial aqueous streams with widely varying chemistries. Application of PF to 'aqueous streams from nuclear materials processing and electroplating operations will be described.

Jan 1, 1999

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008

By A. V. Tarasov, V. M. Paretsky

"The knowledge of the true phase composition of the liquid slag is a very important problem, mastering of which grants the possibilities for the scientifically founded choosing of the decoppering method of the autogenous smelting slags. The investigation using different methods of the phase composition of the flash quenched autogenous copper melt's slags has shown, that the most effective method of the slags' decoppering during smelting with the white matte production is the flotation of the recrystallized slags. In this work the authors posed the problem to realize the slags quenching with the rates similar to those, which are used in the modem investigations devoted to the flash quenching of the ironcontaining alloys, with the subsequent study of the quenched samples using the Mossbauer spectroscopy methods in order to establish the connection between the liquid slag's structure and the metals losses with the slag."

Jan 1, 2000

By T. T. Chen

Raw anode slimes consisting primarily of PbSO4, AgCuSe, Cu3Se2, Cu2-x Se, Cu2O, CuSO4.5H2O, Sn arsenate and Sb-Bi-As oxide are batch-leached with electrolyte-O2 to dissolve Cu. During this process, Cu2O and CuSO4.5H2O are solubilized and the Cu in the selenides is leached with the formation of Ag2Se and Se. A small amount of Cu remains in the Ag2Se, Sn arsenate and Sb-Bi-As oxide. The decopperized slimes are repulped in Na2CO3 solution to convert most of the PbSO4 to NaPb2(CO3)2(OH). The Sn arsenate and Sb-Bi-As oxide partly react, but the Ag2Se is not significantly affected by the Na2CO3 solution. The NaPb2(CO3)2(OH) intermediate phase is dissolved in acetic acid to leave a final product consisting of Ag2Se, Se, Sn arsenate and Sb-Bi-As oxide, together with small amounts of PbSO4, NaPb2(CO3)2(OH) and various gangue constituents.

Jan 1, 1993

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades. EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized.

Jan 1, 2003