Search Documents

By J. P. Piguet, Y. Wileveau

ABSTRACT : An experimental programme for damage assessment was performed in the vicinity of the main shaft of Andra’s Underground Research Laboratory, currently under construction in the East of France, when the shaft is crossing the Kimmeridgian marls between 80 and 100 m depth. The mechanical behaviour was analysed by mean of convergence and displacement measurements. The disturbance into the wall was assessed using numerous methods such as measurement of sonic velocities, permeability measurement and VSP measurement in radial boreholes. The intensity of the damaged zone is low, and its extension does not exceed 0.5 time the radius of the shaft. It does not seem to depend on blasting patterns. ZUSAMMENFASSUNG : Ein Forschungs- und Versuchsprogramm wurde aufgestellt, um die beschädigte Zone im Bereich der Kimmeridgemergel zwischen 80 und 100 Meter Tiefe beim Zugangsschacht des im Bau befindlichen Andralabors im Osten Frankreichs zu berechnen. Das mechanische Verhalten der Formationen wird auf der Grundlage von Konvergenz- und Verschiebungsmessungen ermittelt. Verschiedene Messmethoden, wie z.B. mikroseismische Geschwindigkeite Messungen, Permeabilitäs- und Beschleunigungsbestimmungen in strahlenförmigen Bohranordnungen, erlaubten die Ermittlung des Beschädigungscharakters der Schachtwand. Die Intensität der beschädigten Zone ist niedrig, ihre Ausdehnung übersteigt nicht die Hälfte des Radius des Zugangsstollens und scheint unabhängig vom Schema der Sprengstoffanordnungen zu sein. RESUME : Un programme expérimental visant à évaluer la zone endommagée autour du puits d’accès du Laboratoire de Recherche Souterrain de l’Andra actuellement en construction dans l’Est de la France a été mis en œuvre lors de la traversée des marnes du Kimméridgien entre 80 et 100 m de profondeur. Le comportement mécanique des formations est évalué à partir de mesures de convergence et de déplacements. La mise en œuvre de nombreuses méthodes, telles que des mesures microsismiques, des mesures de perméabilité et d’accélérométrie en forages radiaux, a permis de caractériser l’endommagement en paroi du puits. L’intensité de la zone endommagée est faible et son extension ne dépasse pas 0,5 fois le rayon du puits. L’endommagement semble indépendant des schémas de tirs testés.

Jan 1, 2003

Permitting, engineering and evaluation, detailed design and construction aspects of the Golden Cross goldmining project in New Zealand are briefly reviewed. The extremely lengthy and complicated governmental approval process together with the delaying tactics of opponents of the project are outlined and comment is made on aspects of the draft legislation proposed as part of the overhaul of New Zealand's resource management laws.

Jan 1, 1990

By G S. Lane, G D. Richmond, J Dioses

This paper discusses the methods used in the design of flotation plants, including benchscale batch and locked cycle tests and pilot plant trials. Two case studies are presented, one for the Cadia Hill Gold Mine and the other for the Hellyer copper, zinc and lead plant. These case studies present different problems with widely different target grind sizes, liberation characteristics and HellyerÆs sequential flotation circuit versus CadiaÆs æsimpleÆ copper/gold flotation circuit. They have a common theme in that pyrite forms the principal floatable concentrate diluent. Hellyer ore contains finely disseminated chalcopyrite, sphalerite, galena, and tetrahedrite. The flotation plant design was based on extensive benchscale testwork (including locked cycle tests) on drill core and many months of operation of a 30 tonne per hour æpilot plantÆ, using the old Cleveland Tin Mine process plant suitably modified for the duty. The Cadia concentrator was designed on an extensive benchscale variability testwork program, approximately a dozen locked cycle tests conducted on drill core and two weeks of continuous pilot plant trials on three separate samples obtained from an adit into the orebody. The orebody is a monzonite porphyry with disseminated chalcopyrite/bornite/pyrite of very low grade (0.17 per cent Cu, 0.73 g/t Au). Methods used to establish the appropriate flotation circuits for the treatment of the Hellyer and Cadia ores, as well as the interpretation of the testwork data, are discussed in this paper. Plant performance is reviewed in the context of predicted versus operational performance.

Jan 1, 2002

By Claude Dufresne

The technical development of the niobium-bearing products is to a great extent influenced by the striving of the respective industries to maintain or strengthen their positions in all fields of application against competing materials. South East Asia, China, Eastern Europe and CIS are slowly becoming significant consumers of ferroniobium. As a result, the world niobium market has been stable despite the slowdown in steel production in 2001. This paper will describe present producers, capacities and the current market conditions.

May 1, 2003

By Boris Belenky, M M. Graevsky, R I. Semigin, A E. Frantov

"In the mining industry, most of stripping and rock fragmentation is performed by blasting. The academician N.V. Melnikov has projected that blasting methods would be used to crush 20% of soft rocks and 80435% of medium and hard rocks. Thus, the volume of blasting will continue to increase.This is especially true for electrical blasting, since this method has a number of well known advantages, and in some cases (e.g. for underground blasting in coal mines) it is the only acceptable method."

Jan 1, 1995

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By Y. Boissonnas

INTRODUCTION, The transalpine rail routes in Switzerland are well over one hundred years old. As the established routes no longer meet the demands of the continually increasing volumes of rail traffic between north and south, two new routes through the Alps were planed. The old Gotthard rail line is in fact a mountain railway. The northern and the southern access ramps?with a maximum speed of 80 km/h and a maximum slope of 2.2%?reach the old Gotthard rail tunnel at an elevation of approximately 1,100 m above sea level. This is approximately 900 m higher than the city of Milan. In 1992, the Swiss electorate people voted with an overwhelming majority in favor of the project to build the new base routes through the Alps. The Swiss voted again in 1998 in favor of the financing proposal for the new infrastructure. Swiss Federal Railways together with the BLS Lötschbergbahn were commissioned for the realization and management of the Gotthard and Lötschberg routes. AlpTransit Gotthard Ltd., founded by Swiss Federal Railways, was given the task of managing the design and realization of the Gotthard route until the start of regular service. In the meantime the shorter Lötschberg Base Tunnel was open to traffic in 2007

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

By A. D. Davis

Limestone-based technology for arsenic removal from water is an innovative and promising method. The technology offers the potential for low-cost disposal of a stable waste product after arsenic removal, either in an ordinary landfill or by encapsulation in concrete. Leaching research described in this paper shows that the limestone waste, after encapsulation in concrete, passes the Toxicity Characteristic Leaching Procedure (TCLP) test. Leaching was less than 0.05 mg/L, which is 1/100 of the U.S. EPA?s standard for disposal of arsenic in a landfill. Disposal of arsenic-enriched waste is critical for commercial viability of arsenic-removal technologies. Low-cost disposal gives the limestone-based method an advantage that could help communities meet the new maximum contaminant level of 10 parts per billion for arsenic in drinking water. The ability to recycle the waste material in concrete could add a significant economic benefit, further reducing overall costs.

Jan 1, 2009

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By Keith E. Meyers

Condition monitoring is a viable troubleshooting practice among many industries to extend equipment performance, minimize unplanned downtime, reduce maintenance and repair time and costs, and increase related aspects of plant safety. But obstacles abound for mining, mineral-processing and cement operations striving to implement the technologies. Harsh machine environments can muddy efforts. High vibration in machinery can interfere with wide-spread rollout. Staff expertise or skills may be lacking. And costs may be prohibitive. Fault detection has emerged as a practical and cost-effective solution to identify process and machinery faults before failure interrupts productivity or jeopardizes worker safety. Fault detection can be a stand-alone system or connected to plant automation.

Jan 1, 2005

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

By J. H. Schulman, M. H. Buckenham

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By Frank Cappuccitti, Stephen Chryssoulis, Stamen Dimov

Surface organic microanalysis of platinum (Pt) and palladium (Pd) minerals by TOF MS1 is an attractive complement and potential alternative to conventional collector screening methods. Its attractiveness lies on its ability to focus on individual Pt and Pd mineral particulates, therefore providing a more targeted approach. The only requirement is knowledge of the occurrence (mineral composition, grain size and association) of Pt/Pd in the feed sample. This newly developed technique can detect, and identify collectors and quantitate loadings on individual Pt/Pd mineral particulates at plant concentration levels. Using this technology, collector loadings were measured on Pt and Pd metal plates and on PtS2 and PdS particulates which had been exposed together to aqueous solutions of different collectors. Thus, data were obtained on collector selectivity, the effect of sulphur; and of depressants, the latter in combination with TOF-LIMS2 results. Staged rougher tests on North American and UG-2 ores linked Pt/Pd flotation kinetics with collector loadings and ultimately grade/recovery.

Jan 1, 2003

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By S. Achilleoudes

This paper describes the various factors that contribute to the maximum design pressures acting on box fronts and how these factors influence the mass and economy of box front steelwork. The influence of material density, rock size and moisture content on the incidence of hang ups and mud rushes in the rock pass is also highlighted. The loads acting on any box front are a function of several different parameters. These include natural, operational and excavational parameters. A case study analysis was carried out using UG2 ore and a typical box front structure to demonstrate the relationship between the mass of the box front and the material pressures resulting from variations in the above parameters. Based on the results of this case study, the required design mass of a side mounted box front for a rock pass containing platinumUG2 increases in (close to) linear proportion to % overbreak and is also linearly proportional to the pressure on the face of the box front beyond saturated conditions. The mass of the box front structure also doubles with a 100%increase in over-break which emphasises that a box hole excavation that is as neat as possible will yield a lighter and more econimical box front structure.

Jan 1, 2005

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007