Search Documents

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970's (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird's -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

REFERENCES AND FOOTNOTES 1. U.S. Department of the Interior, Office of Surface Mining. Surface Coal Mining Reclamation: 10 Years of Progress: 1977-1987. Washington, D.C. August 3, 1987.48 pp. (For sale by the Superintendent of Documents, U. S. Government Printing Office, Washington D.C. 20402.) 2. The Rural Abandoned Mine Program (RAMP), authorized by Section 406 of SMCRA, provides for the control and prevention o f erosion and sediment damages from unreclaimed abandoned mine lands. 3. The Small Operator Assistance Program (SOAP), authorized by Section 401(b)(1) and 507(c) of SMCRA authorizes up to 10 percent of the fees collected for the Abandoned Mine Reclamation Fund to be used for technical assistance to help qualified small mine operators obtain techincal data needed for permit applications. Operators who produce fewer than 300,000 tons of coal per year are eligible for assistance. 4. OSM regulations 30 CFR 816.42 and 817.42 require water from areas distrubed by mining activities be in compliance with all applicable state and federal water-quality laws and effluent limitations for coal mining established by the U.S. Environmental Protection Agency. 5. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 6. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 7. Source: OSM Field Office Annual Reports. 8. Johnson, W. and G.C. Miller, Abandoned Coal-Mine Lands: nature, extent, and cost of reclamation. U. S. Bureau of Mines, 1979,29 pp. PHOTOGRAPHIC CREDITS Front cover, pp. i, 1, 2 bottom, 7 right, 10 bottom left, l 1 top, l l bottom right, 12 top, 13 bottom, 14 bottom right, 15,16 bottom, 17 top, 17 bottom right, 18 bottom, 19, 20 bottom, 21 top, 22, 23, 24 bottom, 25 bottom, 26 bottom left, 26 bottom right, 27, 28, 29 top, 30 bottom, 32 bottom right, 33 top, 34 top, 35 top left, 35 bottom left, 35 bottom right, 36 top, 37, top right, 37 bottom, 38 bottom, 39, 41, 42 top, 43 bottom, 44 bottom left, 44 bottom right, 45, 46, 47, and 53: Chuck Meyers, OSM. Page 2 top and center: Tony Fuhs. Page 3: John Sharkowicz, OSM. Page 6 left: North American Coal Corp. Pages 6 right, 7 left, l l bottom left, 13 top left, 13 top right, 17 bottom left, 21 bottom, 25 top left, 25 top right, 29 bottom, 30 center, 32 top, 32 bottom left, and 38 top: Bob Welch, OSM. Page 10 top left: Donald Stump, OSM. Pages 10 right, 14 top right, 14 center right, 18 top, and 44 top: Ron Hill, EPA. Page 12 bottom: Texas Utilities Co. Pages 16 top, 20 top, 24 top: Tennessee Valley Authority. Page 26 top right and 26 center left: Richard Dick, U.S. Bureau of Mines. Pages 30 top, 33 bottom left, 33 bottom right, 35 top right, 36 bottom, 37 top left, 40 top, 40 bottom, 42 bottom, 43 top left, and 43 top right: Jim Boyer, OSM. Page 31 top left, and 31 top right: Bruce Wage, Western Energy Co. Page 31 bottom: Rex Wilson, OSM. Page 34 bottom: West Virginia Division of Abandoned Mine Lands. Page 35 center: William Weist, Jr., OSM.

Jan 1, 1992

TO THE. BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following committees: Membership, Admissions, Papers and Publications, Mining and Metallury (Magazine), and Library. In this review of the year by the Secretary reference frequently will be made to the "Paul" Committee and to the "hotter" Committee. The first is the special committee on Divisional Relationships and the second the special Committee on Ways and Means. These two important committees, appointed by President Harvey S. Mudd under authorization of the Board of Directors on March 21, 1945, were composed as follows:

Jan 1, 1946

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall. Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls, Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013

By S. R. Zimmerley

[In the course of a flotation investi~ntion, a siliceous gold ore was ground ir, R 'ball mill to ~inils 300-mesh. It mas found that the small mount of zlus 300-~esh mnterial had a go12 assw approximately twice that of the oricinal ors, md thst this oversize ~roduct also contained much abra?.ed iron. >!oreover, the gold assay of the abraded iron, which was separated ma~etic-dl:;, wno ei::ht tiaes tkat of the ore. These facts sug,~estsd th~t sone r3laticnshin existed between the abnormally high .gold content and the preseace of abrade4 iron. It was ciecided, therefore, to investl~ate furtkor ths acsoclation of the ;old nith the iron abraded from the balls durir-g grincing. As a nrelininary ex?rr>hent, a samy?le of siliceous gold ore 786 grolznd for 1-1/2 hours i;l 3 ball mill and the nuln was divided into two products electri~mag-etically. The racult s follow: ]

Jan 1, 1937

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"In conventional flotation, fluoride ions selectively would react with the aluminum site on the microcline surface and produce negative charged sites for amine to be adsorbed (Smith, 1976). According to this view, aluminum site is considered as a key feature in feldspar flotation. Generally, fluoride ion has been widely used as a modifying agent in silicate flotation. Since O'Meara's patent appeared on HF -amine reagent system to selectively float feldspar from quartz in 1942, relatively few contributions have been devoted in this issue. The reason might be that the process works very well, and accordingly there is no initiative to investigate in this area. However, due to the awareness of international community to restrict using of hazardous reagents like HF, sound engineering practice to search for alternative methods, not utilizing HF, has been launched. Inspection of literature, one can find several works dealing with this issue.In this contribution, the effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases."

Jan 1, 2003

By Peter Cain

The Phalen Colliery in the Sydney Coalfield is extracting the 2.6 m thick Phalen Seam by the panel and pillar longwall retreat method. Abandoned workings occur in the Harbour Seam 140 m above and overlie the Phalen Colliery. Parts of these workings are flooded, and pose a number of questions relating to the safety of operations in the Phalen Colliery. In order to answer some of these questions, the Cape Breton Development Corporation re-entered an abandoned non-flooded roadway in the Harbour Seam directly above a retreat panel in the Phalen Seam to allow the deployment of instrumentation to monitor interaction effects. Fifteen monitoring sites, each 4.5 m apart, were installed in the 5 East Top Level after it had been re-entered and made safe. Each monitoring station included a vibrating wire strain gauge piezometer and a potentiometric extensometer. The piezometers were attached to rock bolts anchored into the floor and were connected by a flexible standpipe to a constant head apparatus. Variations in hydraulic head due to subsidence were monitored to determine subsidence. The extensometer units were mounted on rock bolts anchored into the floor of the roadway beneath the ribside and monitored ground strains. The instrumentation was capable of remote reading in the event that access to the site was restricted after installation. This paper describes the instrumentation, the installation programme, and some preliminary results.

Jan 1, 1993

By E. D. Gordner

Irrespira ble gutses issuing from the rock fofflb tions ere tJ source of expense ond danger in some metGLl mines. There is a great Variation in the compos i-· tion of such gdses and, os shown 'by recent sampling by the Bureau of ines, the gas rr;;,.y consi$t mostly ct carbon dioxide, (Rocle Strata Gtsses in the Mines of the East Tintic Mining District, by G. E. McElroy, Bu.retau of Mines Serial 2Z75) or f methone (Metruine in Ccalifornia C.old Mines, by B. 0. Picl-Q:lrd i:lnd !.. D. ("iordner, Bure, cf Mines Serial 2303), or nitrogen, sin the present instonce. A nl.liilber of unventilated rt:t.ises in some of the mine of l:l Neva&. district conuin «i'ccumulCltions of l;i hih-nitrogen gas the1t will not supi:ort life or combus­tion. The rdises ore in different geologiecil formations and in widely sep1:1rated. loecslities in the mining district. One ot" two ri::lises in the sme fc.rtr.ation may be full of the gos cand einother nec-r'by be t'ree ot· it. Lives have been lost t:lnd a number of men heave been overcome on enteing unvetilated rtsises in which their­respircable tss hcsd c1ccuni..1.l1::1ted between sldfts. Gener1:1lly, however, the gas see:ns to noozett from the .t'onrbtio:1 ond to ecc1: .. ,i.-1,;.1:.1te so slowly tMt its presence is not suspected t the tfr.1e, bu.t discovered. ed:'t&.c' the raise is t)band.oned. OcCE.isionelly 1 t issues from a ne•.,ly cut cre·tice or fissure under considerca ble pressure and in lar!?e enough '3.'16ntities to overcome or drive 011t men working in unventilated places.

Dec 1, 1922

By Mike Ounpuu

"Locked cycle testing has become more common practice in the last 10 years. Reasons vary from a desire to avoid pilot plant testing, demand for more variability testing within deposits, and perhaps most importantly, a request from the financial institutions who invariably finance many of the projects. Surprisingly, many people don’t understand locked cycle testing, analysis and balancing. This paper provides a brief overview of locked cycle testing, and then progresses into a more detailed discussion on the analysis and balancing of locked cycle test data. The paper endeavors to educate CMP personnel on how to determine if the test was good and if a reasonable metallurgical projection was made. The paper uses case studies to illustrate the key points.INTRODUCTIONA locked cycle test is a repetitive batch used to simulate a continuous circuit. The basic procedure has a complete batch test performed in the first cycle which is then followed by similar batch tests which have “intermediate” material from the previous cycle added to the appropriate location in the current cycle. These batch tests, or cycles, are continued in this iterative manner for an arbitrary number of cycles. The final products from each cycle, i.e. final concentrate and final tailings, are filtered and thus removed from further processing. At the end of the test, all the products, final and intermediate, are dried, weighed and subjected to chemical analysis. The test is balanced and a metallurgical projection is made.This description can be found in many of our classical textbooks for the mineral engineer 1, 2, 3,4. Unfortunately, none of these textbooks provide any discussion beyond the basic procedure. Often, they provide comments such as in Taggart’ where he states; “It is questionable whether in any case it approximates mill results any more closely than the standard batch test”. It is truly surprising that our classic textbooks promote that locked cycle tests are more art than science, and suggest that they can be of dubious value. None of the textbooks provide meaningful insight or discussion in how to assess:"

Jan 1, 2001

By Paul Zinner

Efforts to win an enriched manganiferous product from the Missouri Valley deposits of South Dakota have included an application of most known ore-dressing devices and have been largely unsuccessful. At least two methods showed some promise of success and were the subjects of detailed Investigation by the Bureau of Mines during the period from July 1945 to August 1947. A series of mining and beneficiation tests were undertaken to determine conditions under which the most feasible concentration methods could be employed and to define the limits of such applications in terms of the character of the final beneficiated product. In the absence of a significant current market for any conceivable product of beneficiation, the extent to which applied methods might be considered successful was measured in terms of ratios of recoveries to grade, regardless of the adaptability of such beneficiated products to further metallurgical or direct usage. The results of all investigations show that production of a shale-free, concretionary, manganese-bearing product by any known method requires great sacrifices in manganese recovery. Products of beneficiation, with specifications permitting some inclusion of shale, can probably be most effectively produced by methods employing specialized jigging equipment as the principal functional unit of a process.

Jan 1, 1949

By McLennan T, Howells E, Zastawny H, Watt J. S

Nuclear techniques have been used to determine the solids weight fraction (W) and ash content of (fine) coal in slurries independent of voidage variations. The method is based on the correlation between W and the hydrogen concentration Hsl (wt/wt) of the slurry. Hsl is determined by combining measurements of neutron moderation and ?-ray transmission. Both Wand ash content are determined by combining the above measurements with the ash-sensitive measurement of X-ray backscatter compensated by a measurement of iron K X-ray intensity.The nuclear analysis system, called the SIRO coal slurry gauge, has been proved in a six-week plant trial at the BHP Steelworks washery at Newcastle, NSW. Several probes, each containing a radioisotope source and scintillation detector, were immersed directly into the coal slurry in the feed box upstream from the bank of flotation cells. For 140 samples W, ash and voidage varied in the ranges of 0 to 13 wt percent, 26 to 41 wt per cent and 0 to 4 vol. per cent, respectively. The r.m.s. difference in solids weight fraction, determined by probe measurements and conventional assay, was 0·52 wt per cent. Ash was determined with an r.m.s. difference of 2·0 wt percent in the coal. Better sampling techniques were used in the last half of the plant trial, and r.m.s. differences were 0.35 wt per cent solids and 1·5 wt per cent ash.

Jan 1, 1986

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal-conductivity method because of the relatively small amounts of this inert as present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to Continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which Vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method, and a continuums analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of lanes. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation. Production is checked against the helium removed from the gas, which before the installation of the thermal-conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By David A. Monaghan

On January 14, 1974 a fire occurred in the 3 East mains of the Joanne Mine of Eastern Associated Coal Corp. in Rachel, West Virginia. The mine was evacuated without injury and sealed completely at the surface within 24 hours. It was decided by the coal company along with the U, S, Bureau of Mines, the West Virginia Bureau of Mints and MESA that remote sealing of the fire zone would be attempted. This report summarizes the remote sealing effort and those activities directly related to the remote sealing effort. This chapter provides a brief history of previous remote sealing attempts, a description of the recently developed remote sealing system and a description of the Joanne Mine operation as it related to and affected the remote sealing effort.

Jan 1, 1975

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By B Lumsden, B Lacouture

"Red Dog is one of the largest zinc mines in the world both in terms of reserves and annual production. In 2013, Red Dog produced 551,300 mt of contained zinc and 96,700 mt of contained lead. The mine, which is located in Northwest Alaska, is a partnership between Teck Alaska Incorporated, the operator of the mine and NANA Regional Corporation Inc, the local land owner. The Aqqaluk deposit, which is the current source of ore, has an average grade of 15.8% Zn, 4.1% Pb and 73 g/t Ag with the main minerals being sphalerite, galena, pyrite, barite and quartz. Surveys of the zinc flotation circuit at Red Dog identified that a substantial amount of fully liberated, sub 20 micron sphalerite particles were being lost to final tailings. As a means of improving fine sphalerite recovery, a four month plant trial of magnetic conditioning was conducted in the zinc retreat circuit. Magnetic conditioning technology has already been commissioned in several concentrators around the world to agglomerate fine paramagnetic minerals, increasing their probability of bubble collision and recovery in a flotation cell. The results of the four month plant trial at Red Dog showed that at a high level of confidence, a 1% increase in zinc recovery or zinc recovery and zinc concentrate grade combined was achieved with magnetic conditioning. The resulting economic benefit, which is also at a high level of confidence, is significant to Red Dog and therefore, magnetic conditioning has been permanently incorporated into the Red Dog zinc flotation circuit.IntroductionRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine."

Jan 1, 2016

By J Webster-Brown

The Tui Mine is an abandoned Pb-Zn mine giving rise to water quality problems in the Te Aroha region of Coromandel, New Zealand. When sampled in September 2002, for example, both the Tui and Tunakohoia Streams draining the mine site exceeded ANZECC (2000) water quality guidelines for aquatic life protection (Cu, Cd and Zn) and recreational quality (Cd). Based on trace metal mass flux (kg/yr) from parts of the mine site, the principal pathways by which Cu, Zn and Cd contamination reach these streams have been identified as:the tailings dam leachate,the diverted stream water from above the dam,the drainage from Adit 5 (which accounts for 95 % of Zn and Cd contamination in Tunakohoia Stream), andto a lesser extent, run-off from waste rock piles below Adit 4 level. Of the various remediation options, which have been proposed for the site, the following are identified as providing the best protection for the Tui and Tunakohoia streams:stabilising the tailings dam embankment and capping the embankment and tailings,constructing and/or cleaning out engineered diversion drains around the perimeter of the tailings dam to divert surface water away from the tailings dam, andinstalling bulkheads within Adit 5. A formal postal survey of the people of Te Aroha (66 respondents from 230 surveys) indicated that their priority was that the site be made safe for the public to visit, and used for recreation. As soil samples in potential recreational areas of the mine site, significantly exceeded guideline values for Cu, Pb, Zn, Cd and As, soil removal or capping clearly also needs to be part of a remediation plan. Development of the site as a historical/ecotourism area was viewed favourably, as this may encourage more visitors to the Te Aroha area as well as educate local residents.

Jan 1, 2003