Search Documents

By N. Kumar Kittusamy

A field study was conducted to evaluate seat designs on shuttle cars. Eight operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers also measured the levels of vehicle jarring/jolting. Four basic seat designs were compared on low and mid-coal seam shuttle cars during production operations at two underground coal mines. Two seats were currently used on the shuttle cars and another two were NIOSH designs. Objective data were collected using accelerometers with pre-amplifiers and filters connected to a data recorder; whereas subjective data were gathered with a visual analog scale (VAS) and a questionnaire. Results from measured levels of jarring/jolting showed that the NIOSH Seat L2A smoothed out bumps better than any other seats. Using the VAS, mid-seam and low-seam shuttle car operators rated the levels of jarring/jolting and discomfort lower with the NIOSH seat than the other seats. Questionnaire responses indicated that operators rated NIOSH seat designs as more comfortable. This research will provide the industry with better seat designs for isolating jarring/jolting in vehicles. Furthermore, researchers plan to improve the NIOSH seats using information gathered in this study.

Jan 1, 2003

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By Randall M. Wheeler

The purpose of this workshop is to illustrate how computer software can be used to evaluate blast design timing and simulate probable vibration characteristics. The workshop will be presented in two parts. Part I will cover the COMPU-BLAST Blast Design and Timing Analysis Program. Part II will focus on the ALPHA-BUST Vibration Analysis and Waveform Simulation Program. The information presented in the workshop will show how these two programs can be used together to help plan blast designs and aid in the control of vibration effects.

Jan 1, 1991

By R. J. Durheim

Detailed investigations have been conducted into 21 rockbursts which caused damage to excavations in deep South African gold mines, in many instances resulting in the death or serious injury of workers. The objective of this study is to determine the principal factors controlling the severity and distribution of damage, so that strategies to reduce the hazard of rockbursts may be developed. It was found that the source mechanism is often controlled by the mine layout, and regional structures such as faults and dykes; while local rock conditions and support systems strongly influence the location and severity of damage. In the short term the most important lever for reducing the rockburst hazard is the effective implementation of existing rock engineering knowledge and technology.

Jan 1, 1998

By V. V. Nazimko, A. I. Hohotva, S. N. Alexandrov, V. P. Sazhnev, V. S. Zaharov

Ground behaviour in the vicinity of a roadway has been investigated using a physical model and in situ tests during a roof fall. It was discovered that behaviour of the ground is governed by irreversible displacements of adjacent rock clusters. The cluster is a short-living sector of a rock mass that moves as a solid body. For the lack of degree of freedom, the rock mass must be divided into clusters that are forced to move one after another in space and in time. These clusters permanently rearrange and reform during irreversible (inelastic) ground deformation. The crowded clusters have to yield to each other and alter their velocity and direction of movement to accommodate their motion into the excavation. Such behaviour involves uneven and irregular vertical deflection and the movement of adjacent rock blocks in the roof, sides and floor of an opening. Such movement destroys the symmetry of horizontal displacements with respect to the centre line of the opening. A set of indicators that a roof fall is imminent has been identified. Horizontal displacements and dilation must be controlled in order to maintain the stability of an underground opening. Such a state retains the self-supporting effect of the roof and contributes to rock bolts bearing capacity.

Jan 1, 2003

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By T Rohde, P Defferrard

In 2010 a store and release cover (the cover) was constructed on the south waste rock dump (SWRD) at Century mine. This also included aerial seeding of province native trees and shrub seeds. The purpose of the cover is to reduce percolation into the potentially acid-forming (PAF) waste rock by maintaining a compacted reduced permeability layer (RPL) at near-saturated conditions. This is achieved by overlaying the RPL with a 1.5 to 2 m thickness of soil-mulch. The soil-mulch has a hummocky final surface that captures rainfall, so it does not runoff, allowing it in part to infiltrate, with excess water removed by evaporation and transpiration. The RPL is the trafficked surface of the SWRD.The unsaturated behaviour of the cover is being monitored by instrumentation including volumetric water content and matric suction sensors and a weather station capable of estimating evapotranspiration. The instrumentation allows for direct measurement of infiltration into the cover, storage of rainfall, percolation through the base of the cover and in situ soil water characteristic curves (SWCC).The key functions used to describe the unsaturated behaviour of the cover materials is the SWCC and the unsaturated hydraulic conductivity function. The SWCC is a plot of soil water versus soil suction. It provides the loci of moisture states of a soil from the saturated to the dry state.The paper presents the results of five years of monitoring. It shows that total infiltration into the top of the SWRD was about 1.6 – 3.7% of cumulative rainfall over five years, with most of the infiltration going into storage within the cover. Runoff from the top of the dump is not allowed therefore, the remaining 95% of the total rainfall was lost to evaporation or as lateral flow when infiltration reached the RPL. The paper presents some simple analyses of the wetting by rainfall infiltration of the cover, leading to breakthrough at the base. Field data are used to support the analyses.Presentation of the SWRD water balance is also included in the paper using SVFLUX™GE which is a finite element model that simulates water transport through a saturated or unsaturated medium.CITATION:Defferrard, P and Rohde, T, 2018. Five years of cover performance monitoring and modelling for a store and release cover at Century Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 179–189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By J. R. G. Williamson

The Mining Division of Iscor, an integrated minerals and metals company, has recently completed a feasibility study for the establishment of a new heavy minerals mine and smelter in the Richards Bay area of KwaZulu-Natal, South Africa. The mine will produce a heavy mineral concentrate containing ilmenite, zircon, rutile and leucoxene which will be beneficiated at a central processing complex close to Empangeni. The ilmenite will be smelted to produce high-grade titania slag and pig iron for export. The ancient dune containing the mineral deposit is located some distance inland of the coastal dunes, and the sands contain a high proportion of extremely fine material which must be extracted ahead of the gravity separation process. Of the 56 million tonnes to be mined annually over the ten-year life of the mine approximately 23,4%?a total of 13,1 million tonnes of minus 45 micron residue fines?will have to be disposed of in a containment facility. The origin of the fine material is from the weathering of amphibole minerals. The remaining coarse sands will be returned to the mined area to re-create the original dune configuration. A number of options for the disposal of the residue fines have been examined and specialised laboratory tests undertaken to determine the deposition behaviour of the fines. The final solution involved the use of a ?sub-aerial? technique for deposition of fine material in a disposal facility. The resulting arrangement will adequately meet technical and environmental criteria. Upon closure after 10 years of operation, the surface of the disposal facility will be returned to sugar cane cultivation The paper refers to the various options considered and describes the problems associated with competent disposal of the residue fines and the development details of the final disposal facility.

Jan 1, 1997

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1991

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By E. D. Gardner

"Trolley lines used in connection with electric haulage in mines are a source of danger and many lives have been lost by men accidentally coming in contact with the wires. Usually the wires in metal mines are sufficiently guarded to prevent men from touching them with their person or by pieces of steel which they may be carrying or their shoulders, while walking along the level. However, it is difficult to guard effectively the wires at loading chutes along the haulage ways and in spite of safe guards, chute tappers have been electrocuted through loading bars accidentally touching the trolley line.To overcome this danger the Calumet & Arizona Mining Co., at Lowell, Arizona formely used a hinged V-shaped trough made of 1-inch by 6-inch lumber, that was dropped over the wire in front of the chute, when the cars were being loaded. This arrangement interfered with the easy operation of the chute, and a cut-out device for the trolley line was devised by W. R. Gibson, chief electrician for the company. This cut-out is efficient easily constructed and roes not interfere with the operations at the chutes or with the motors operating on the same level.When the cut-out is open the electric current is carried past the gap by an insulated wire on the opposite side of the drift. A hinged board drops down over the ends of the trolley guard when the slide is open and Prevents anything touching the live wires. About ninety of these cut-outs are now in use in the mine,The levels under the scopes are timbered with drift sets placed 5 feet apart, and the loading chutes take up the space between two sets. All trolley wires in. the company's mines are carried 6 feet above the rails and guarded by two 1/2 by 6-inch boards placed on either side of the wire."

May 1, 1921

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By A. Swanson

The Australian coal industry has been subdued in recent years and only a few new plants have been constructed, but the drive for greater efficiency has seen continued technological developments. The paper lists the new plants and major upgrades, plus summarizes technical developments in the areas of dense medium processing, fine coal treatment, froth flotation, dewatering and on-line analysers.

Jan 1, 2001