Search Documents

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By T. Payne

Underground heat issues are mainly focused on the detrimental effects to a workers health. However, working in hot, humid conditions has other negative effects. Studies have shown that safety, productivity, workforce morale and operating cost are also worsened in these conditions. The human body has several mechanisms for rejecting heat and remaining cool. However, once the air temperature exceeds about 34°C, the only effective mechanism is by evaporation of sweat from the skin. This is assisted by acclimatisation which is the human body?s enhanced ability to combat extended exposure to heat. The body has to remain well hydrated when working in heat as even small degrees of dehydration cause significant decreases in the ability to work in heat. There are two ways in which heat load can be reduced: Through use of refrigeration/vent/cooling to reduce thermal stress on workers; Reduce the contribution that heat sources have to underground heat load (e.g. reduce idle time, fleet size, etc). Some of the sources of underground heat have the potential to be more manageable than others. Geothermal heat and heat from autocompression will be found in all mining situations in varying degrees depending on geothermal gradient and surface temperature, however, the use of equipment and blasting may be streamlined to reduce the underground heat load. It is through a combination of the available options that most mines will successfully control their heat related problems. Mt Isa, which has been a focus for heat related study in Australia, has successfully implemented protocols for working in heat. Through combining these with the installation of a surface bulk air cooling plant, Mt Isa has consistently reduced the incidence of heat illness. This is likely to be the most cost effective method of reducing heat load for deep mines in Australia. Shallower mines which may only occasionally encounter hot conditions should consider more portable cooling options. This study will review the heat issues in underground Australian metalliferous mines.

Jan 1, 2009

By F F. Pitard

The optimization of metallurgical processes requires knowledge of the heterogeneity carried by constituents of interest. The common scenario, almost an industry standard, is to rely on the engineering firm who in turn relies on favorite manufacturers of sampling equipment to provide the appropriate sampling systems in the plant to perform accurate metallurgical accounting. This sequence is flawed from the beginning to the end because everything should be based on a careful understanding of the Theory of Sampling (TOS) by the company project team and their expert who invariably would suggest various approaches and different sampling systems.The necessary progressive and iterative approach should be that the company’s project team (mining or other industries) would do its home work to have a good understanding of the geometallurgy, mineralogy and texture of the ore in each geological unit so consultants and engineers would have the best information to start with. Then a reputable sampling expert would recommend which sampling systems are needed, so the company would require engineering firms to follow pre-established, non-negotiable requirements, and finally select the sampling equipment existing on the market today that is most likely to lead to accurate and precise enough metallurgical accounting.It is the author’s experience that when this necessary progressive and iterative approach is bypassed, sampling systems installed in the plant are likely to transgress the most elementary rules of sampling correctness. Invariably the argument is that the company cannot afford correct sampling systems for metallurgical accounting as suggested in the Theory of Sampling. There is nothing that is farther from the truth when later problems will develop and inevitable reconciliation difficulties with miners and geologists become daily routine with impossible answers; as a last resource the sampling expert may be called to perform a post-mortem analysis.The progressive and iterative approach suggested in this paper should be a due diligence requirement for any bank providing a loan for an important new mining project; anything less is most likely to generate unpleasant financial losses; historical, well-known examples are referred to.CITATION:Pitard, F F, 2015. A progressive, iterative approach leading to reliable metallurgical accounting sampling systems, in Proceedings MetPlant 2015, pp 78–91 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By S. Kahraman

The correlations between the modulus ratio and penetration rate of rotary and percussive drills were statistically investigated using the raw data obtained from the experimental works of different researchers. An inverse power law was found between the modulus ratio and the penetration rate of rotary and diamond drills. The penetration rate of rotary drills and diamond drills decrease with an increasing modulus ratio. The penetration rates of percussive drills increase with an increasing modulus ratio. There are significant linear correlations between the penetration rates of percussive drills and the modulus ratio. In one of the cases of percussive drilling, a strong correlation between the penetration rate and the modulus ratio was found for the rocks having a porosity value lower 1.23 %. It can be concluded that the modulus ratio might be a representative measure of rock drilling efficiency. However, further study is necessary to check the validity of the derived equations for other rock types. The effect of porosity on the correlations between the modulus ratio and penetration rate needs to be further investigated.

Jan 1, 2003

By P. J. D. Lloyd

At first I read this paper with interest, which grew to fascination, and ended up with horror. Such reactions to a supposedly scientific contribution are rare, and I believe the coal mining community must be warned in the strongest possible terms against the recommendations that this paper makes. The paper purports to have assessed statistically two sets of data on methane concentrations recorded in the return air from Turkish longwalls. The first set of data, from their Table I, is reproduced in Table I below. The data have been rearranged in classes to indicate the underlying distribution. While there is only limited data (N=33), the distribution looks as if it could be the sum of two normal distributions with means around 0.5 and 0.8, or possibly a log-normal distribution. What is quite clear is that it is nota single normal distribution.

Jan 1, 2004

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By J. K. Lemley

The human element in large measure dictates success in contracting relationships. Because of our professional backgrounds, we view contracts primarily as either engineers, contractors or owners. A beneficial contractual environment--one in which decisions, risks and benefits are shared--demands equal consideration of all three points of view. Most of the older cities in the United States, for example, suffer from bad contracts--generalized, patched-together documents that represent an accumulation of modifications originally written to compensate for specific situations that have occurred over the years. Because such documents lack coherence, they often present conflicting instructions which lead to defensive, ultimately destructive attitudes among the parties involved in the day-to-day administration of the project. Good contract development begins with a strong central philosophy to which the details of the contract can be related. First, the owner should establish a comprehensive philosophy in which risks between the parties are identified. Following this, a specific contract document can be written to satisfy this established philosophy. The contrast between two opposed contractual situations, NYC Water Tunnel Number Three and the Seabrook Nuclear Power Plant Cooling Water Tunnels, illustrates how comprehensive, well-written contracts--contracts which share both risks and benefits--provide the basis for achieving quality construction that will reward engineer, contractor and owner.

Jan 1, 1983

By Mario Morin

The application of underground pre-concentration technology to narrow vein mining has the potential to change the entire economics of bulk mining methods when used in narrow vein situations. The rejection of waste at or near the face means that a higher-grade ore can be sent to surface. The waste rock can be reused directly as backfill. Swelling of the muck through blasting means that only 60 to 65% can be used as fill. Planning and scheduling of the fill usage is key to the success of this method. Through the use of simulation and system analysis, this paper examines the planning and scheduling implications of underground pre-concentration when applied to traditional narrow vein mining methods (cut-and-fill /drift-and-fill, longhole, AVOCA). It considers the logistical factors that represent potential system bottlenecks that are key to understanding the correct implementation and control strategies.

Oct 1, 2004

A major problem in open pit mine planning is to determine the optimum pit limit of the mine. The optimum pit limit is the one with maximum discounted net profit and satisfies technical conditions. A number of optimisation techniques have been proposed for determination of pit limits. Among these techniques, those based on graph theory are suitable to solve the three-dimensional (3D) problem. In this paper, two maximum flow methods named, Dinic's algorithm and Push-Relabel algorithm have been used to find the optimum pit limit of an iron ore mine. This method has been implemented in Gol-e-Gohar iron mine in south east of Iran in order to find the final pit limit. Issues, like properties of the mine and orebody, are studied. These properties include wall slope, sulfur and phosphor grade restrictions. The result shows that these properties have significant effect on the determined pit limit.

Dec 6, 2010

Old Copper Flotation Tailings Waste Reprocessing

Sep 13, 2010

By M. Ounpuu

"Gold, because of low head grade and recovery, is usually of minor importance in the economics of base metal flotation mills. Because of the above little metallurgical attention is usually provided to gold in these mills. But collectively, the gold losses can be significant. For instance, Noranda presently has interest in 13 base metal flotation mills with a collective gold recovery of only 50%. Gold losses are in the order of 150.000 oz per year!The Noranda Technology Centre, in cooperation with Noranda's milling operations, has been investigating the potential of gravity concentration of gold from base metal flotation mills. This paper outlines the pilot and plant testing conducted at three operations with distinctly different ore types; porphyry copper, complex massive sulphide and polymetallic semi-massive sulphide. Testing has been with the Knelson Concentrator which has proven to successfully recover fine gold in a simple, trouble free circuit. Discussion of issues which have risen from the testwork is included. INTRODUCTIONGold, because of low head grade and recovery, is usually of minor importance in the economics of poly-metallic base metal ores. TABLE I presents gold heads and recovery for some of Noranda's base metal mills. It should be noted that the stated recoveries are to payable concentrates, but does not reflect the actual payable gold recovery which in cases is significantly lower. Noranda's average gold recovery into a gold payable concentrates is about 45%. This equates to a collective loss in the order of $57 MM per year of gold"

Jan 1, 1992

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By R. Altindag

The rock brittleness is one of the most important rock properties that affect the drill-ability of rocks. It is supposed that the increase in rock brittleness causes the increase in penetration rate. The drill-ability of rocks depends on many factors. These factors can be separated as two parts depending on a machine, bit type, rotational speed, thrust, blow frequency, flushing, and rock properties, brittleness, compressive strength, structure, hardness, etc. In this paper, the relationship between brittleness and drill-ability index, which is used in the prediction analysis of the penetration rate of rotary blast hole drills, were examined using regression analysis. It is also seen that significant correlations exist between brittleness and the drill-ability index.

Jan 1, 2002

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

By B. Kenny

The aim of this paper is to provide an overview of existing forms of subcontracting in the South African mining industry. A descriptive framework is developed to understand different subcontracting arrangements. We argue that, in order to do so, it is important to distinguish between labour broking and gang subcontracting. Data resulting from a research project (including an analysis of historical sources, interviews with contractors and focus group interviews with mineworkers) is presented to highlight the implications of changing formations of subcontracting for the South African mining industry in the late 1990s. Apart from the subcontracting of ?traditional? functions, such as shaft sinking, access development, catering and hostel maintenance, contractors are now used in ?core? mining activities. In some instances, whole shafts are ?outsourced? to outside agencies. It is argued that certain of the subcontracting arrangements have serious implications for the ability of the mining industry to improve health and safety standards. Some of the practices can potentially result in conflict between different categories of workers, and, as a result, instability in the industry.

Jan 1, 1999

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010