Search Documents

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

After a three-year period characterized by inflation, recession, depressed metal prices, lack of demand, enormous world inventories, and rapidly escalating costs, the Canadian mining industry is showing welcome signs of recovery. A rise in world metal prices and particularly strong demand for gold, uranium, and coal have stimulated the industry in early 1979. In this atmosphere of growing optimism, over 3000 mineral industry executives, economists, geologists, and mining and metallurgical engineers convened in Montreal, April 26-29, for Canada's largest mining convention, the Annual General Meeting of the Canadian Institute of Mining and Metallurgy.

Jan 6, 1979

Jan 1, 1970

By Alan Mayton, Bertrand Valero, Christopher Jobes, Farid Amirouche

Exposure to vibration induced in and around underground mine’s exploration is a major concern to vehicles operators. Most of these drivers over time develop serious spinal musculoskeletal and discs problems causing low back injuries. The first purpose of this paper is to analyze the performance and dynamic response of driver/operator when subjected to different levels of vibration due to rough road conditions depicted in a mine field. The second purpose of the paper is to quantify the energy transmission in the presence of seat padding with special characteristics and active suspension. Using experimental testing data collected at NIOSH/PRL (National Institute for Occupational Safety and Health/ Pittsburgh Research Laboratory) along with model simulation algorithms developed at the University of Illinois at Chicago we investigated how acceleration transfer functions as well as absorbed power affects the different parts of the body. To this end, we used a previously validated human model which includes the head, torso segments and legs. The connective forces between body segments were modeled through modal analysis techniques from previous experimental data at the UIC Vehicle Technology Laboratory. The absorbed power and energy transmitted to the body are used as an index measure to assess the viability of the different seat padding’s and active seat suspension control strategies.

Flotation testing has been done at laboratory scale on hematite mineral and ore samples using stage additions of various hydroxamates. Chemisorption of hydroxamate species onto the hematite surface was inferred from the results, possibly involving both the undissociated hydroxamic acid and hydroxamate ion as maximum recovery occurred close to the pKa of the hydroxamic acid. Flotation testing on a specular hematite ore containing 40 per cent Fe and 42.5 per cent silica gave highest iron grades in concentrate at pH 6, in contrast to published data which suggested pH 9 as the optimum value for ore processing. Using octyl hydroxamate, a rougher concentrate assaying 67 per cent Fe at 51 per cent recovery was obtained using four stage additions of 50 g/t at pH 6. For lower grade concentrates still meeting the chemical analysis for pigment grade micaceous hematite (minimum Fe assay 60 per cent) iron recoveries of 80 per cent were possible for stage additions of 50 g/t octyl hydroxamate in the pH range 6-8.

Jan 1, 1999

By G. Wu, S. Liu

In view of the singleness of traditional methods about international petroleum (Brant) price forecast, ten main factors that affect international petroleum price are fully analysed. Based on time series method and multivariate linear regression method, the simulation model with the theory and idea of system simulation is firstly established. And this forecasting system realizes visual operation under the environment of MATLAB/SIMULINK. So this article tries a new way for further exploring petroleum price’s running law and guiding its forecasting practice. Keywords: Petroleum price forecast, system simulation, residual error, physical flows information flows

Jan 1, 2003

By Evan J. Owen, Virginia T. McLemore

Rare earth elements (REE) and critical minerals are increasingly becoming more important in our technological society and are used in many of our electronic devices (such as cell phones, computer monitors, wind turbines, etc.), batteries, and magnets. Measuring REE and critical minerals in ashed coal approximates the REE and critical minerals in the fly or bottom ash remaining after coal is burned at a power plant, where REE and other critical minerals could be leached. In New Mexico, there are 26 coal fields in Late Cretaceous rocks in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, Rare Earth, and Critical Minerals) program. Higher concentrations of REE (as much as 2103 ppm total REE) are found locally in ashed coals from the basins. More chemical and mineralogical analyses are required to fully understand the distribution and origin of REE in these deposits. As the demand for REE increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics, perhaps even from coal.

Feb 1, 2025

By K. F. Bailey

Naturally occurring asbestos in aggregate and other mineral deposits, and the release of asbestos fibers into the ambient environment, is a public health concern. Determining the presence of asbestos in an ore body also presents a considerable sampling and analytical challenge. Improper and inaccurate identification of asbestos can result in unwarranted public and worker panic leading to significant costs to mine operators both in terms of dollars and company image. Some companies have been forced out of business simply because they had the non-asbestiform, prismatic variety of one of the six asbestos minerals. In the late 70’s, asbestos was found as a contaminate in a trap rock quarry in Rockville, Maryland. This discovery led to a massive overreaction by federal, state and local governments. In 1986, the Occupational Safety and Health Administration (OSHA) promulgated a final rule that regulated the common non-asbestiform mineral habits of actinolite, tremolite, and anthophyllite as if they were asbestos. The rule was reversed after a six-year struggle. Recently, the Libby, Montana, W. R. Grace vermiculite - asbestos, as well as the California chrysotile in serpentinite, and the New Jersey Southdown quarry – asbestos events have rekindled the entire issue of naturally occurring asbestos. It is time to get this concern addressed with sound science so that real asbestos is properly identified and controlled.

Jan 1, 2002

By B. Swarbrick

Today’s mining occurs in a dynamic world of conflicting objectives. Mining companies have to look further than a traditional cash flow analysis to determine the potential value of developing a mine. In particular, proposals for new mine developments undergo rigorous scrutiny by a variety of stakeholders including regulators, NGO’s, and the local communities. From a business risk perspective, how mining companies address stakeholder concerns can have a dramatic impact on the success of the project. In today’s mining environment mining companies must continue to ‘walk the talk’ to stay in business, particularly during downturns in the business cycle. Falconbridge’s Raglan Mine is an example of a project that was successfully developed in a region that is sensitive from many perspectives, including environmental, socio economic, and regulatory. Close working relationships with local stakeholders along with strong environmental management systems are necessary elements of continued success for the project.

Jan 1, 2000

By Sam Friedman

The Bureau of Mines conducted experiments using bench-scale apparatus to explore the effect of large changes in process variables on the yield and composition of the gases produced by passing 800° C steam through a fixed bed of Pittsburgh seam (hvab) coal. The total yield of combustible gases increased throughout the given range for the following variables: Superficial steam velocity increasing from 0.02 to 0.12 fps, pressure increasing from 1,000 to 6,000 psig, residence time increasing from 0 to 60 minutes, and temperature increasing from 800° to 900° C; however, a greater increase in the yield of hydrogen in comparison with the increase in yield of methane reduced the gross heating value of the gas to around 470 Btu per scf at conditions giving the maximum yield. Pressures of 1,000, 3,000, and 6,000 psig at 0.09 fps steam velocity, 800° C, and 60 minutes residence time, respectively, produced methane yields of 20, 24, and 22 percent, based on maf coal, with the gross heating value of the CO2-free gas decreasing from 552 to 520 and to 470 Btu per scf. Methane concentrations in the CO2-free gas were 26, 22, and 14 percent, respectively. Based on the gross heating value of the coal, the percentage of the heating value recovered in the gas was 60, 71, and 87 percent, respectively. The use of tungsten sulfide as a catalyst for converting carbon oxides and hydrogen into methane was explored briefly using both a sulfur-free gas rich in methane and a sulfur-bearing synthesis gas (3H2:1CO).

Jan 1, 1968

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987

By S. Mishra, C. Shon, D. Saylak

Only 40% of fly ash generated by the power plants in US are recycled and used for commercial applications. Of these, the high lime, Class C ash had been preferred. Systematic laboratory and field-scale studies have shown that, by including calcium chloride in the mix design of stabilization of roadbed materials, both Class C and Class F fly ashes can be effectively utilized. Test data reveal that the addition of calcium chloride to the system accelerates its curing rate, thereby increasing early strength and long term durability of the constructed road. For road construction, a preblended Class F fly ash–CaCl2 system tends to be more forgiving than the Class C fly ash–CaCl2 system. The former system produces more durable roads. The role of calcium chloride as an accelerator in these systems is discussed along with a mathematical model developed for fly ash- CaCl2 stabilized roadbed systems.

Jan 1, 2007

By AIME AIME

PRESIDENT BASSETT'S gavel called the Annual Business Meeting to order shortly after 10 a. m. on Tuesday. On motion of Eugene McAuliffe, reading of the minutes was dispensed with and Mr. Bassett read his annual report of the year's activities as follows : During the year I have visited eighteen of the twenty- seven sections, making an average of GG 2/3 per cent. The invitation to come again has always been extended, but in only one case have I been able to visit the same section twice. Chicago entertained the president twice during 1930. Mrs. Bassett accompanied me on visits to ten sections. Everywhere we have found the most cordial hospitality and a gratifying enthusiasm for the Institute. If anyone had fault to find with the management or felt dissatisfied with what was being done, it was carefully concealed. I am happy to report to you an agreeable, helpful and progressive spirit in each of the sections visited.

Jan 1, 1931

By Christian Heili

In 1991 the Government of the Republic of Zambia passed legislation providing for the privatisation of Zambia Consolidated Copper Mines Limited (ZCCM). The newly formed Mining Companies, established after nearly a decade of difficult and protracted negotiations on such matters as, cash at close; retained percentage interest by ZCCM; equity investment; future investment commitment and tax concessions, were faced with great internal challenges and a harsh external environment. There was a convergence of a number of negative forces that had and will continue to have an impact on the mining environment in Zambia. The most crucial of these being, the competitive pressures of the global economy, fluctuating copper price and the prevailing HIV/AIDS pandemic. In the short period after privatisation, the Industry has seen the collapse of Binani Industries (Luanshya Mine), the withdrawal of Anglo America Corporation from Konkola Copper Mines Plc and the disposal of Chambishi Cobalt and Acid Plants by Anglovaal Mining Ltd. The objective of this paper is to provide a theoretical and practically researched foundation, which may be used to assist Zambian Mining Companies in making informed decisions on the issue of Strategic Outsourcing and the degree to which this may support the successful and sustainable growth of the Zambian Copper Mining Industry. If judiciously implemented, Strategic Outsourcing has the potential to generate a practical business valuation and process to assist Mine Management in the achievement of their business goals and consequently the return on investment to their Shareholders.

Jan 1, 2005

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By Peter G. Chamberlain

The surge in gold and silver prices during the 1970's attracted many new mining operators and has rekindled interest among experienced ones. With its low capital investment requirements and fast payout, leaching has attracted many operators--particularly those with small or low- grade deposits. Although in certain situations leaching offers many advantages over conventional mining methods, many operators are uncertain how these relatively new techniques should be implemented. Consequently the Bureau of Mines has prepared this circular to disseminate information on gold and silver leaching practices, techniques, and problem. Engineering data gathered from 26 operations indicate that most ores are leached in heaps following crushing and distribution on pads. Metal values are recovered from cyanide leach solutions using either zinc precipitation or charcoal adsorption. Potential problems that my hamper on block development of a leaching operation are poor percolation characteristics of the ore, calcium salt buildup, low temperatures, and solution losses. An extensive bibliography on gold and silver leaching is appended.

Jan 1, 1984

By Dustin Vickress

The premature failure of copper staves in the lower stack and bosh is frequently the cause for an interim blast furnace repair at great cost to the blast furnace owner. Protective accretions may form on the stave hot face, but when these accretions are lost the staves can begin to deteriorate both due to abrasive wear from exposure to the descending burden materials and due to thermal cracking from exposure to hightemperature process excursions. These mechanisms can lead to failure of cooling passages, which forces blast furnace operators to shut off these channels, accelerating the rate of copper stave wear. Finger cooler technology was developed to extend blast furnace life by restoring cooling to damaged staves. Evidence for their effectiveness is presented herein in the form of experimental test work and conjugate heat transfer (CHT) analysis carried out using computational fluid dynamics (CFD) simulations. These tests demonstrate that under typical blast furnace excursion conditions, a stave fitted with finger coolers will undergo half the temperature rise of a stave fitted with conventional cigar coolers.

Aug 17, 2017