Search Documents

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer's standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By P M. Hetherington, M P. Murphy, K E. Crook, F Pym

Resource characterisation is critical for informed decisions in both strategic and operational space. The sources of information for resource characterisation are limited by: direct measurement of resource attributes, such as grades, rock-types, mineralogy, and are available only from sparse locations, ie drill holes; or indirect geophysical measurements such as seismic, gravity or electro[1]magnetic survey. Data collection tools, methods, and processing technologies are constantly improving providing a broad spectrum of options for data collection strategies. The cost of each data survey varies from thousands to millions of dollars with the value of each additional data having diminishing return for a particular business decision. The value of information analysis provides the optimal decision on data collection strategy within a limited available budget. This work presents an example of value of information analysis for new Blast Hole Assay Tool (BHAT) and Reverse Circulation Grade Control (RCGC) data used in addition to the wider spaced exploration data. The value of information is quantified in terms of reduction of grade uncertainty, ore loss and dilution by comparing different combinations of data collection methods. Four different strategies were considered: exploration samples in addition to 50 per cent of blastholes surveyed with BHAT, exploration samples in addition to 33 per cent of blastholes surveyed with BHAT, exploration with wide-spaced RCGC data, and exploration without additional grade control. For each strategy the observed values have been simulated using advanced multivariate geostatistical simulations and compared with simulated ground truth models. The calculated uncertainty, ore loss and dilution informed the optimal data collection strategy. Opportunity to reduce sample density from the nominal 50 per cent of drill holes was evaluated.

Mar 22, 2022

By Richard Brummer, John Hadjigeorgiou, Patrick Andrieux

Some of the major challenges associated with underground mining at depth and/or under high extraction ratios are related to the resulting high stress levels, which can lead to the failure and collapse of the rock mass surrounding the excavations. Sudden and violent failures, which can have severe consequences, represent the highest degree of difficulty in terms of underground personnel exposure, erratic and unpredictable production, ground rehabilitation requirements, possible reserve losses and overall mining costs.

Jan 1, 2012

By Parida K. M, Paramguru R. K

Laboratory-scale studies aimed at developing a process for solubilising manganese values from a low grade pyrolusite containing material using low grade pyrite, both available in India, are described. Leaching 21 parts by mole of pyrolusite with 6 and 26 parts by mole of pyrite and sulphuric acid respectively results in good manganese dissolution (98 per cent) at 100&#176;C within one hour. The probable kinetics of the leaching process has also been given.

Jan 1, 1995

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975

As already said Pattin&apos;s map and the later one of Evans&apos; showed coal in several places in Ohio as early as 1750, and possibly 1748; the reference on the latter map was&apos; to an exposure near Bolivar, in Tuscarawas County, as well as along the Hocking River. So far. as now known, it &apos;was not mined in either place until 1810. George Croghan, in descending the Ohio with his party in 1765, mentions an "Alum Hill" which they saw near the present site of Pomeroy, probably an exposure of saline deposits, but does not mention coal. As settlement north of the Ohio River was prohibited until 1787, no coal was mined until long after that date. In 1785 a survey of seven ranges in the Ohio country was made, the line running west from a point on the north bank of &apos;the Ohio River, due north of the western termination of the southern boundary of Pennsylvania. The surveyors noted, "from hence to Stoney Brook between two very steep and high Ridges; it is eight yards wide, its bottom is of Slate and Sand Stone, and in many parts of it are large pieces of excellent Coal washed by, the Rains from the Neighboring Hills."&apos; This was the present Yellow Creek, and the coal was from some of the lower measures. The Scioto Company published a pamphlet in French in 1787, to promote the sale of their lands and emigration to them, in which was said,

Jan 1, 1942

By Wayne A. Charlie

An experimental test program being conducted at Colorado State University and involves the study of the behavior of water saturated sands under shock and explosive loadings. The study is being conducted to evaluate potential blast induced changes in dynamic soil properties, soil shear strength loss (liquefaction) and densification of water saturated sands under single and multishock loadings. This paper presents testing and measurement objectives, and the equipment and instrumentation developed to load, measure, record and analyze the transient and long term soil behavior. The laboratory shock facility is capable of generating multi-shock pulses with milli-second rise time, peak stress amplitudes of up to 35,000 KPa (5000 psi), peak particle velocity of 5000 cm/set and peak acceleration of 10,000 g. The field explosive facility subjects saturated soil to controlled explosive loadings. Of major interest is the soil strain and water pressure, both during and after the passage of the stress wave, as a function of peak particle velocity, peak strain, loading rate, soil density, initial confining stress and the number of loadings. Based on data obtained to date, soil densification is due to consolidation following liquefaction.

Jan 1, 1991

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn&apos;t "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By Marcello Crispi, Valdir Silva, Juarez Moraes

Companhia Vale do Rio Dote - CVRD is the largest mining company in Brazil and the largest iron ore producer in the world. Serra Geral Mine (SGM) is located at Iron Quadrangle of the State of Minas Gerais, approximately 80 kilometers from Belo Horizonte. Hematite and Itabirite are the two main minerals. A blasting with a spherical charge has been introduced at Serra Geral Mine, an iron ore producer in Brazil, belongs to the CVRD (51%) Kawasaki Steel Corporation (24.5%) others (24.5%), in order to improve fragmentation, as well, load, transportation and crushing productivity. This paper will present the results of a successful blast design with a spherical charge carried out by Serra Geral Mine, the Department of Mining Engineering at Escola de Minas - Federal University of Ouro Preto-UFOP associated to a Blasting Engineering Consultant. The results obtained in the field tests and how it was possible to increase the blast pattern in 53%, which allowed one reduction around 31% in the cost of blasting operation in the Serra Geral Mine, will be discussed in details.

Jan 1, 2002

By Márcio Aurélio dos Santos

A Automação Industrial utiliza de forma intensiva os mesmos equipamentos e softwares de TI como servidores, historiadores, switches, firewall, dentre outros. No entanto, são poucas as áreas de automação que aplicam de forma eficaz todos os controles e cuidados que esses ativos requerem. Neste cenário, a garantia de altos níveis de disponibilidade dos sistemas de automação inicia-se pelo ambiente físico no qual tais sistemas estão instalados. É comum a improvisação de ambientes inadequados dentro das áreas industriais ou a instalação em subestações elétricas que não foram construídas com o rigor necessário para receber os ativos de TI Industrial utilizados nos sistemas automação. A solução para manter elevados os índices de disponibilidade destes ativos é, sem dúvida, instalá-los em Data Centers, comumente utilizados nas áreas de TI, o que é facilmente justificável pelo fato de que a indisponibilidade dos ativos de automação representa um impacto maior aos resultados das indústrias ao se comparar com a indisponibilidade dos ativos de “TI Corporativa”. Assim, este trabalho conceitua um ambiente de Data Center, discute as particularidades relacionadas à Automação Industrial (projetos de cabeamento estruturado e as interligações entre os níveis 1 e 2 de Automação) e apresenta as estratégias que a Samarco Mineração está adotando com relação ao tema.

Jul 30, 2018

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve&apos;s life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young&apos;s modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By John Gordon

Rare earth elements (REE) required in modern technological products are found in shale rocks above and below coal seams. Often during the process of mining coal, shale rock adjacent to the seam inadvertently is removed then diverted to landfill sites. Ecologically sound and potentially economic methods of extracting the REEs from these landfills are proposed. Methods include utilizing geomemembrane barrier beneath the landfill site, ion exchanging with moderate pH, slightly acidic, sodium chloride solutions. Sodium hydroxide is utilized to precipitate the REE-hydroxides subsequently converted to REE-chlorides with suitable amount of hydrochloric acid. All acid and base streams are co-produced with efficient membrane/electrolysis technology. Concentrated-REE chlorides are transported tocentralized solventextraction facilities for isolation and purification. Solvent extraction processes also employ the methodology of using co-produced acid/base streams. This paper details minimization of environmental impacts and maximizing economics to produce valuable REEs while increasing the economics of coal mining.

Mar 1, 2018

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By P Mikula, R Geranmayeh, R Carlton, M Ferguson, R Whiting

The concept of using specially designed slot blasts to mine through stress abutments that intersect faults, while controlling fault-slip seismicity, has come of age at Mt Charlotte Mine. Due to the high and adverse stress field and the presence of major faults, the mine is vulnerable to significant fault-slip seismicity. As mining proceeded, advancing stress abutments around various mined areas encroached on several major subvertical faults. If the sequence formed a diminishing pillar between stope and fault, the removal or failure of that pillar daylighted the fault, and often resulted in significant fault-slip seismicity. A new strategy called ‘Tight Slot Blasting’ (TSB) was developed to restrain or dampen this style of fault-slip movement. The TSB has geometric similarities to a conventional cut-off slot used to create stress shadows, but its function is different. Its objective is to trigger and control a sudden shift of the stress state on a fault from an initial stable state, through an unstable transition, to a second stable state. A TSB firing advances a long tall narrow slot through a stressed abutment between a stope void and a nearby fault, using a rapid blast with a low swell ratio, so that the slot substantially and rapidly fills with blasted rock fragments. During the blast process, the stressed rock is rapidly removed and transformed into the fragmented rock fill in the slot. The strategy deliberately allows a fault-slip episode to manifest at a chosen time and place. The tight-packed broken rock in the slot performs an essential shock-absorbing function by controlling the slip amount and rate on the fault, while at the same time the fill becomes compacted by the movement. This controls the dissipation of fault-slip energy, and greatly reduces the seismic response in time and space. A small closure across the slot occurs, with consequent relaxation and destressing of the adjacent rock mass. Stress monitoring data shows that slot creation lowers the abutment stress in the nearby rock mass, while the newly placed fragmented rock fill acts as a shock absorber, providing considerable resistance to substantial fault-slip movement that otherwise could deliver a significant seismic event. First used in 2007, the strategy has been refined to become a routine specialised practice for management of seismically hazardous situations at Mt Charlotte, with 12 successful TSBs conducted to date. Despite mining through multiple high stress abutments, seismic reactions have not exceeded ML 2.1 with any TSB firing, all remaining below the site tolerable maximum of ML 2.3. This paper presents an overview of the strategy, and five case examples of the strategy in critical stressed areas in July 2016, Sept 2017, Dec 2017 and two in Oct 2020. The strategy has successfully managed the seismicity and is expected to remain an essential part of the seismic management plan at Mt Charlotte Mine.

Nov 29, 2022

Jan 1, 1891

By H Allday

The mining industry’s attention has shifted over the last decade with the recovery from the downturn resulting in greater development of innovation and new work methods in a bid to remain competitive and deliver higher productivity. The emphasis on cost reduction to improve profit margins has primarily been the focus of the “work smarter” campaigns embraced within the industry. But is this strategy holistically the best-for-business, or does it place a ceiling on revenue opportunities and inhibit mining companies from truly maximising value? Businesses need to maintain a balance between active cost management and revenue generation often resulting in cost reduction strategies at site level. These strategies have merit, assessing areas of cost wastage across operations and creating space for opportunity. However, this potentially can create distractions from the goal of enabling growth and lead to the sacrifice of quality and delivery. Focusing too heavily on cost reductions without addressing revenue generation is an unprofitable lens to look through, and the relationships between cost, revenue, quality and profit margin can often be overlooked resulting in missed opportunity to maximise value. How these relationships are effectively employed by mining companies to reap the rewards from an overarching corporate perspective down to site level remains a fluid concept depending on the nature, operating market and strategy of the business. A common directive from businesses to their operations is to strive for greater profitability and productivity. The quantification of these requirements, and the nature of the cascading message delivered, impacts the methods employed by the operational team to meet the expectations of the business. Cascaded strategies, if not delivered with appropriate participation and buy-in can often be perceived to be knee-jerk and create frustration for operations who are squeezed to deliver on expectations by slashing site costs. This squeezing is not only felt by the mining operation but at the individual level and can result in increased team stresses. In some cases, this may also steer behaviours towards activities that result in corner cutting and an elevation of operational risk, potentially increasing associated incidents and injury. Driving down costs by any means can create an unhealthy tunnel vision where value is no-longer assessed for best-forbusiness results. By flipping the viewpoint to a value-based approach revenue opportunity may be realised and potentially exceeded, however this opportunity may be missed if value is over shadowed by a cost heavy focus. By analysing a selection of real operational cases (ranging from mining contractors through to in-house mining giants), it becomes apparent that practical revenue maximisation strategies are not only key to an increase in value and cash flow but to a stronger understanding of business drivers for sites and operators alike. In the cases evaluated additional revenue opportunities are foregone in favour of cost reduction strategies resulting in negative impacts on the associated operations and wider businesses. Alignment towards value generation is king. If strategies are not implemented focusing towards value and revenue maximisation, the opportunity loss experienced by mining operations could continue be great and the question should be posed; when the next up-turn hits will operations be ready to reap the rewards or still have a glass ceiling above their heads?

Mar 15, 2021