Search Documents

By F. G. Schwartz

This circular presents the results of a survey of research on jet fuel thermal stability jointly sponsored by the National Petroleum Refiners Association (NPRA), Tulsa, Okla., and the Bureau of Mines. The development of supersonic planes has led to many problems that did not exist in the operation of subsonic aircraft. One of the most important of these is rapid deterioration of the fuel at the high temperatures to which it is subjected. At higher speeds, aerodynamic heating of the airframe imposes severe thermal problems, and conventional techniques of rejecting the heat to the atmosphere become impractical. The fuel is the only material present in sufficient bulk to be used as a heat sink. Thus, the fuel is subjected to aerodynamic heating and also is used to dissipate heat from lubricating oil, hydraulic fluid, electronic equipment, wheel wells, and cabin air. Consequently, the fuels may have to withstand both moderate temperatures for sustained periods in the fuel tanks and higher temperatures for brief periods during transfer from the tanks to the combustion chamber. Because of high temperatures, insoluble residue or gum may form in the fuel and contribute to heat exchanger fouling and to clogging of the fuel manifolds, nozzles, control systems, and other components of the fuel system.

Jan 1, 1962

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By M. Morin

"This paper examines the design issues associated with the integration of mineral processing within underground mining using a total systems approach. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins.The performance of such integrated systems in terms of productivity, economical and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefits, while underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems. IntroductionTotal systems thinking is simple in principle but complex to implement. The premise is that to achieve optimum effectiveness and efficiency from a system, the complete system must be considered. Using this approach will avoid the situation where the optimization of a localized component of any system results in a negative impact on the performance of the complete system. Take for example the parts manager who reduces inventory costs without consideration of the consequences to the plant. If the plant goes down and a part is unavailable, it would then cost significantly more than the cost of having it in inventory (Ackoff, 1994).A tool for applying total systems thinking toward understanding and analyzing different mineral extraction options is the structured analysis and design techniques (SADT). Originally developed by Ross (1977), SADT is a formal systems engineering methodology (FIPS PUB, 1993) for process and enterprise modelling (Marca and McGowan, 1993). Figure 1 presents a highlevel structured analysis of the traditional or conventional metal extraction process. There are three sequential processes with several arrows entering or exiting each process. In SADT, inputs always enter from the left-hand side and exit as outputs of the process on the right-hand side. Constraints affecting the transformation of inputs to outputs enter the process from the top while resources or mechanisms enabling the transformation enter from the bottom. SADT is a hierarchical decomposition technique and further analysis is undertaken by expanding downward into each process."

Jan 1, 2003

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By Beatryz C. Mendes, Henrique de Paula Santos, Kléos M. L. Cesar, Eduardo Antônio G. Marques, Maurício Paulo F. Fontes, Rita de Cássia S. S. Alvarenga

Inadequate discard of industrial solid waste is a risk to human health and to the environment. Aiming at softening environmental damage caused by deposition on soil of an ink residue, from washing of printers used in carton box packages, it is intended to incorporate this residue into soil-cement bricks. The residue has other use potentialities such as in screeds, pavement parts, fertilizer, paints, etc. However, to explore these potentialities it is fundamental to assess the risks that the several forms of use of this residue can cause. For such, in this work the chemical analysis of the residue was performed in order to know its main chemical compounds, in addition to its characteristics of leaching and solubilization. The chemical composition assay showed traces of some heavy metals such as Pb, Cd, Cr, Zn, Al and Cu, although the residue-generating company uses ink labeled as heavy metals free. Among the elements analyzed in leaching and solubilization, some had concentration above the limit allowed by The Brazilian Codes. This code is based on CFR—Title 40—Protection of Environment—Part 260–265—Harzardous waste management. Therefore, it is suggested that the residue has a limited use to avoid contamination of ground water.

Mar 1, 2017

By R. D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of general accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2000

By Forest J. Sur

"This report describes an exploratory project conducted by the Bureau of Mines on a fluorite deposit near Vado, N. Mex. Results of trenching are given. Together with analyses made upon samples of the ore. The Federal Geological Survey3/ completed a preliminary geologic study and mapped the deposit during the summer of 1944. A Bureau engineer examined the deposit in August 1944. As a result of these investigations, it was concluded that the deposit contained substantial inferred ore reserves. Exploratory work was recommended to obtain information that might possibly lead to production from the property. Assistance was given the Bureau by the Geological Survey.A gasoline-powered air compressor, other equipment, and supplies were delivered to the property from January 20 to 25, 1943. Trenching began under the direction of a Bureau of Mines engineer on January 25, 1947, and ended on March 15, 1945. The results of trenching and sampling form he basis of this report.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. IT is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, R.G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervisions of Dr. R. S. Dean, assistant director."

Sep 1, 1946

Jan 1, 1944

Jan 1, 1944

Jan 1, 1967

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By Jyothi Rajesh Kumar, Jin-Young Lee

21st century is electronic revolution in human lives as well as energy is one of the most significant tasks. Rare earth elements (REEs) occupy a key role in daily life as well as high-tech industrial applications. REEs are one of the energy critical elements; for sustainable growth, it depends on multiple extraction and separation technologies including solvent extraction and ionic liquid-based extraction methods.

Mar 1, 2017

By Hale Y. M

Multielement reconnaissance geochemistry coupled with ground scintillation gamma ray measurements has been used to investigate the dispersion patterns of uranium and other major and trace elements in the arid Palmyrides region of central Syria. This region occupies an interplatform depression in the northern part of the Arabia Plate, upon which sediments up to 10 km thick have accumulated. Outcrops of strongly fractured Mesozoic and Cenozoic rocks form two major mountain belts, the northern and southern Palmyrides, between which is located the closed Ad-Daww basin, with a thick Neogene and Quaternary clastic cover. Among the various lithologies, phosphorites are well represented. Uranium and associated elements have been incorporated into the Upper Cretaceous and Lower Palaeogene sediments, especially the phosphorites, which are well represented in the region. These elements are derived from three possible sources, namely, sea water, Lower Cretaceous volcanism and metalliferous fluids leaking along taphrogenic lineaments. In and around the phosphorites, numerous traces of secondary uranium mineralization occur. Over 500 geochemical samples of outcropping rock, wadi and playa sediments, overburden and groundwaters were taken over an area of approximately 9000 sq km. Most samples were analyzed for 25 major and trace elements by nebulization ICPAES; for As, Sb, Bi and Se by hydride generation and ICPAES; and for U, Th and La and other REE by neutron activation analysis.

Jan 1, 1988

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986