Search Documents

By J. -B. C. Varnier, J. A. Cremeens, D. D. Overton

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County in Colorado in the United States were investigated using three-dimensional discrete element modeling methods. Large-scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back-analysis was conducted using prefailure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. IntroductionThe Pikeview Quarry is an aggregate quarry located approximately 8 km (5 miles) northwest of Colorado Springs in El Paso County, CO, USA. The quarry has been operated by several owners since the early 1900s. According to the U.S. Mine Safety and Health Administration (MSHA, 1986), the quarry has been a major source of construction aggregate for the Colorado Springs area for many years. In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy.A large-scale slope failure occurred on Dec. 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on Sept. 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure.The objective of this paper is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry, and both of these mechanisms were given equal credence in the present study. Quarry excavation and backfilling was a key factor in the slope instability for both failure mechanisms. The excavation was backfilled in stages in an effort to provide slope support. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability."

Jan 3, 2018

By James C. Duchon

The use of extended workdays (regular shift lengths of 10 or 12 h (hour), while still maintaining a 4O-h workweek) in mining operations is attracting growing interest in the United States. There is very little doubt that extended workdays is a very popular alternative among the work force because of the significant increase in days off, including weekends, especially when compared with traditional rotation schedules of working seven straight shifts or having only one weekend off every 4 to 6 weeks. However, there are some serious concerns by management, workers, unions, and various governmental policymakers that working 10-or 12-h days may create an added risk of accidents and health problems. The U.S. Bureau of Mines reviewed the literature studies related to the safety and performance issues of extended workdays. This report presents a summary of those findings. The studies examined in this review are divided into three sections: (1) laboratory, (2) field, and (3) accident and injury analysis. In general, results are inconclusive. Studies have shown both positive and negative effects. It is concluded, therefore, that in industries such as mining where accidents are a serious concern, special measures and evaluation in the use of extended workdays be considered.

Jan 1, 1994

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

By D. V. Keller

The use of a static bath of a heavy liquid of intermediate density between two mineral phases has been employed for beneficiation for over one-hundred years (1-6). In the case of the heavy liquid separation of coal from its included mineral matter, laboratory (3) and commercial (2,4) techniques have employed a halohydrocarbon or mixtures thereof, or solutions of inorganic salts and water with a specific gravity in the range of 2.0 to 1.30. As a laboratory tool, the heavy liquid separation is generally regarded as a standard permitting the "ideal" separation of a product coal and reject mineral matter. Each of the products in this case is polyphase since the separation is only based on apparent specific gravity of the product or reject material. The "Otisca Process" is an anhydrous heavy liquid separation process which employs a parting liquid with certain physical and chemical characteristics which make it particularly advantageous for expanding the laboratory separation process into the realm of commercial coal cleaning. The two key characteristics of the parting liquid are: 1) the heavy liquid does not react significantly with the coal product or reject material, and 2) the liquid permits complete dispersion of the coal product particles throughout the separation bath. The first point, i.e., the lack of liquid coal reaction (7-11), may be cited as one of the major reasons for the failure of other attempts at commercialization of heavy liquid processes. For example, if reaction does occur between the heavy liquid and coal or mineral matter, complete heavy liquid recovery becomes a very expensive complex process. The costs of heavy liquids alone prohibit their loss in the process as will be demonstrated later.

Jan 1, 1977

By Dwain K. Butler

INTRODUCTION Characterization of a site for the prediction and simulation of dynamic events requires the determination of mechanical properties of the rock at stress/strain levels and rates and at a scale appropriate for the events and critical structures involved. The structures of interest can be on the surface, underground, or designed to impact and penetrate into the site (projectiles). Dynamic events of interest are equally diverse: seismic waves from distance earthquakes or explosions; close-in phenomena associated with earthquakes and explosions; vibrations associated with heavy equipment or machinery; and stress transients associated with impact and penetration. The complexity of site characterization depends on two factors not specifically related to the nature of the site itself: the stress levels generated by the dynamic event and the sophistication of the prediction and simulation techniques. For very high stress levels, such as occur near a nuclear detonation, and for low stress levels, such as occur during seismic wave propagation, site characterization is simplified, and often certain details of the site are not particularly important, such as shear strength variations in the case of very high stress levels. In the intermediate stress range, however, all descriptive relations are non- linear, a complete finite strain constitutive model is required, and all details of the site, such as lithology and fracture distribution, become important. The site characterization must be complete enough to support the most sophisticated prediction and simulation technique that will be applied to the analysis of the dynamic event. The procedures of site characterization are illustrated in this paper by a specific dynamic event, projectile impact and penetration, and a specific site, an outcrop of Dakota Sandstone near San Ysidro, New Mexico. The structure of interest was the projectile itself: nominally, 1.5 m in length, 0.165 m in diameter, 180 kg

Jan 1, 1984

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By Paulo Vinícius Souza da Conceição

A demanda por aços com baixos teores de enxofre tem propiciado o aprimoramento das técnicas de dessulfuração de gusa. O presente trabalho tem como o objetivo mostrar, através de um modelo em água, a influência da injeção auxiliar de gás através do impeller S.I.R.A.M sobre o tempo de mistura no processo do Reator Kanbara (KR) e sobre a área de contato desse gás com o líquido. Diferentes velocidades de rotação do impeller, vazões de gás injetado e pontos de injeção foram avaliados. Os resultados obtidos foram comparados com a condição de não injeção de gás. Observou-se que a injeção de gás é capaz de reduzir o tempo total de mistura.

Aug 17, 2017

Karl L. Fetters moves to the front of the AIME organization this month as the 1964 President of the Institute. He will take the chair vacated by outgoing President Roger V. Pierce at the Annual Meeting in New York, already well-rehearsed in his forthcoming duties after a year of preparation as AIME President-Elect. Dr. Fetters is highly qualified for his new responsibilities on both the administrative and professional level. For the past five years, he has been vice president for research and development at The Youngstown Sheet and Tube Co. in Ohio, where he has achieved wide recognition as an out- standing metallurgist and executive. A native of Alliance, Ohio, he obtained his early education in the public schools of his home town and displayed a singular precocity when he launched his professional career as a chemist for the Morgan Engineering Co. at the age of 16. His new career, however, was soon set aside in favor of four years of higher education at the Carnegie Institute of Technology, whence he emerged in 1931 with a bachelor's degree in metallurgical engineering. Surprisingly, and perhaps owing to the employment stringencies of the Depression years, the first job his new qualifications earned him was that of stationary engineer at the Cunningham Sanitarium in Cleveland. After two years of ministering to the mechanical ailments of this institution, Dr. Fetters relinquished his post for a more suitable one in the field of metallurgy.

Jan 2, 1964

By Donghai Li, Cheng Pan, Pan Chen, Xuewei Lv, Mei Liu

"Chromite concentrate after beneficiation can not be directly used in the electric furnace. Therefore sintering is one of the effective way to agglomeration, by which the chromite concentrate can be utilized and the power cost of ferrochrome smelting can be reduced. The properties of raw materials and the sintering process of chromite concentrate were studied in this work. The results showed that chromite concentrate used can hardly granulated alone, while chlorite addition can improve the effect of granulation. Moisture plays an important role in sintering process. The granulation effect is optimal when the amount of water addition is 12%. Strength and abrasion index are the evaluation indexes of sinter quality. It was found that the strength of sinter increased with coke dosage increasing to 12%, and then decreased when it continuously increased. Opposite regularities were found for the abrasion index of the sinter.1 IntroductionChromium is a very important metal element which is mostly used in the production of stainless steel. In the earth, it is always formed compound with iron as ferrochromium spinel (FeO.Cr203), and its mineralogical name is chromite.[1] Currently, the global production of chrome ore is about 20 million tonnage every year , in which fine ore (less than 8 mm) accounted for about 80% [2] Although the price of the fine ore is cheaper than the lump one, too much fines will lead to the poor permeability and causes increased electricity consumption while producing ferrochrome. Therefore, the agglomeration process of chrome ore is one of the effective measures to increase the usage ratio of fine ore."

Jan 1, 2013

By R. B. Scott, J. Hewitson

The paper investigates the historical information relating to spontaneous heatings which have occurred within the area from 1955 to date. From this information the seams most liable are identified and the location within the workings is enumerated, together with the possible reason for the occurrence of the heatings. Details are given of the precautions taken during development, working and withdrawal. Sampling procedures are outlined and the interpretation of the results is discussed. Reference is made to the various types of material and techniques employed in both preventing and combating heatings and examples are given of their relative cost and the operational experience obtained. Special observations are made on the changes in mining techniques and their influence on spontaneous combustion.

May 23, 1905

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006

By Walter W. R. May

FOR more than 25 years a few business men who represent virile private enterprise in the Pacific Northwest have been trying to awaken the community to the potential benefits of an open Columbia River. No threat of government com- petition then hung over the industry, which was adjusted to state regulation. Numerous sites were engineered and the findings were laid before the operators of heavy industry in the East, Middle West, and South -even of Europe. These engineering data became, if not the basis, the inspiration upon which the U. S. Army Engineers eventually were to "build the Columbia River Bible" - their great document known as House Document 103, the report on the Columbia River and minor tributaries.

Jan 1, 1940

By J. U. MacEwan

THE basis on which the modern metallurgical industry is operated is the endeavour to attain maximum return in purchasing power for the least expenditure of energy. This has always been the general objective of the industry, as of all industries. In recent years, however, it has received a new emphasis. Today, as never before, increased attention is being directed to the detailed study of plant operations and the application of scientific knowledge and of business principles in order to achieve the maximum efficiency. This new emphasis is the result in large part of the new problems and conditions with which the industry has been confronted, chief among which are the following: (l) Development of new ore-bodies and the treatment of complex ores. (2) Necessity of achieving a greater degree of purity in some of the metals in order to meet the newly discovered demands for some of the industrial metals. (3) Discovery of new markets for many of the metals, either in pure form or in the form of alloys. ( 4) Change in values, absolute or relative, of some of the important metals. (5) Increasing scale of investment in expensive plant and equipment, which makes imperative most efficient utilization if total unit costs are to be kept to a minimum. (6) Increasing scale of operations in some important branches of the industry, which also makes essential maximum efficiency in organization, administration, and operation. The success with which the metallurgical industry has met the problems created by these changing conditions has been due primarily to the following factors: (1) Results of research and experimental work carried on by universities, government laboratories, and many private corporations in the industry itself. (2) Closet study of every detail of plant operation, both from the technological and from the economic point of view, with the object of increasing plant efficiency. (3) Interchange of information and experience amongst the operating companies. It is only by the concerted efforts of numerous investigators and experimenters that the underlying fundamentals of plant operations can be learned. The exchange of results permits their easy assembly and correlation with maximum benefit to the whole industry. Unnecessary duplication of research and experimental work is avoided and the industry as a whole is able to reap the fruits of this work with the maximum of-speed and efficiency. (4) Advances made in recent years in so-called 'scientific management' in industry as a whole and the application of the principles learned to the metallurgical industry. A review of the modern trends in extractive non-ferrous metallurgical processes illustrates the afore-mentioned new conditions and problems, and gives some idea of the methods by which they have been and are being surmounted.

Jan 1, 1937

By Fred Tarquinio, Giovanni Bonita, Lars Wagner

"A new embassy for the Peoples Republic of China is under construction in Washington, DC. The 475,000 square feet (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. A vertical soil nail wall was used as the primary support of excavation system for the project. The soil nail wall was irregularly shaped, benched in areas, and up to 98 feet (29.9 m) in height. The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Design and construction challenges included soft soil conditions, inside wall corners, underground utilities, seismic impacts from blasting, and logistical and political factors. Overall, wall movements were lower than expected, with maximum horizontal movement less than 0.25% of the total height of the excavation. INTRODUCTIONThe proposed Embassy of the Peoples Republic of China in Washington, DC, will consist of about 475,000 ft2 (44,125 m2) of building space and contain up to four fl oor levels above ground and fi ve levels of basement (Figure 1). When completed, the building will be the largest embassy in Washington, DC. The architect for the project, Pei Partnership Architects, along with the world-renowned architect I.M. Pei, made effi cient use of the site by inserting the building into the existing slope. Consequently, excavations reach heights up to 98 feet (29.9 m) on the southern side of the property and 42 feet (12.8 m) on the northern side.The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. The location of the building relative to the property line called for tight excavation requirements, including precise wall positions and shotcrete tolerances. Design and construction challenges included soft soil conditions, inside wall corners, arched walls, underground utilities, seismic impacts from blasting, and logistical and political factors."

Jan 1, 2007

By Alfred Boyles

"HEREDITY"' in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mecha-nism of freezing in cast iron. The experiments described below are largely concerned with that problem.

Jan 1, 1937

By R. W. Van Dolah

The Bureau of Mines t.ced its investigations into sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) to define the scaling law for safe separation from detonating AN-FO. Both missile- and non-missile-producing AN-FO donors, weighing up to 5,400 pounds, were employed with acceptors of the same size. The usual cube-root scaling law was not confirmed; exponents for the relationship S = f(Wx) for AN were 0.51 with non¬missile-producing donors and 0.61 for missile-producing donors. For AN-FO an exponent of 0.80 was indicated in the missile-producing case. AN-F0 in polyethylene bags appeared somewhat more easily initiated than bulk AN-FO. The efficacy of barricades in protecting AN charges was investigated. detonation distances were reduced from one-third to one-seventh when filled barricades were employed. The investigation was extended to dynamite with both types of donors. With 1,600-pound missile-producing donors and an equivalent weight of dynamite, initiation would be expected in 50 percent of the trials at 167 feet. The corresponding value in the non-missile case was 67 feet. The data developed in this program of sympathetic detonation will allow the development of a rational set of safe separation distances for AN, AN-FO, and explosives.

Jan 1, 1966

By Y. Guglielmi, C. Gout, P. Henry, P. Dick, C. Nussbaum

For a decade, observations and experiments conducted in underground environments worldwide (mines, underground research laboratories - URL) made it possible to bridge the scale gap between laboratory scale and large scale faults. Indeed, underground rock laboratories allow developing decameter scale relatively well constrained experiments at the smallest distance from the hypocenters. URL’s experiments allowed developing new monitoring technologies coupling pressure-strain-seismic measurements and reproducing complete earthquakes sequences analogous to natural ones. They also allowed exploring past movements of faults and sometimes also paleofluids in three dimensions and characterizing different fault architectures and hydromechanical properties in unaltered conditions. This is particularly important in the study of faults affecting clay formations which could not be observed at the Earth’s surface because of the high alteration. Here we show how examples from the Mont Terri (Switzerland) and Tournemire (France) The URLs may help in (i) defining the concepts of fault architecture in shales, (ii) estimating fault hydromechanical properties from field decameter scale experiments. Some key results are that faults which are critically stressed or at the rupture limit can reactivate for stresses variations within the range of those produced by shallow underground excavations, and that slight micrometer-to-millimeter scale reactivations may lead to large factor-of-10-to-1000 permeability increases. Such promising results show that URL’s experiments may bring new insights on some key processes that control the relations between fault stability and permeability evolutions in very permeable layers.

Jan 1, 2015

By Jim Hardy, Tim McKnight

"The thermal mass flow controller, or MFC, has become an instrument of choice for the monitoring and controlling of process gas flow throughout the materials processing industry. In the semiconductor industry, these MFCs are used on over 70% of the processing tools. Reliability and accuracy are major concerns for the users of the MFCs. Calibration and characterization technologies for the development and implementation of mass flow devices are described. Sources of inaccuracy in process gas handling are described, and a model to correct for these inaccuracies is outlined. A gravimetric calibrator is described that allows flow sensors to be calibrated in corrosive, reactive gases to an accuracy of 0.3% of reading, at least an order of magnitude better than previously possible. All described capabilities are implemented in a Department of Energy User Facility which is available to industry and universities to test and develop gas flow sensors and controllers and evaluate their performance related to environmental effects, reliability, reproducibility, and accuracy.IntroductionMaterials processing is at the heart of semiconductor manufacturing. To make today's advanced integrated circuits, silicon wafers are subjected to over 200 process steps. Most of these steps involve processes such as etching, implanting, diffusion, annealing, deposition, and lithography (resist deposition and hardening). Often one or more process gases are used to complete the process step. To achieve the quality and performance required in the micro devices, accurate measurement and control of these gases is essential. The Oak Ridge National Laboratory (ORNL), in conjunction with the semiconductor industry, has been working to improve process gas measurement and control accuracy and reliability. Standardized test methods have been developed to characterize and benchmark the performance of mass flow controllers (MFCs), the method of choice for monitoring and controlling gas delivery. Testbeds have been designed and fabricated to produce repeatable and accurate data using these standards. Baseline testing was performed along with development of a unique mass flow instrument, the gravimetric calibrator."

Jan 1, 1997