Search Documents

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By H. Mischo, R. Ellmies

Uranium has been mined in Namibia since the 1970s. The worldwide increasing need for energy in the early 2000s has led to the development and opening of a second uranium mine in 2007 and has triggered an increased interest in uranium exploration, often referred to as “the Namibian Uranium Rush.” In all, four mining licenses have been granted by the Namibian Government, which currently has two mines in operation, a third undertaking trial mining and the fourth in project finance negotiations. In addition, highly intensive prospecting activities at additional deposits are at an advanced stage. The finalization of the strategic environmental impact assessment (SEA) on uranium mining in 2010, the first of its kind and scale in the world, has enabled the Namibian government to assess this uranium rush and its tremendous legal, socioeconomic and environmental impacts and to prepare for the different future scenarios conceivable when this article was written in 2011, including both a skyrocketing and a complete breakdown of demand scenario. The Fukushima disaster and plans of the Namibian government to significantly increase royalties and company taxes in 2011 have threatened the market situation, forcing investors to reevaluate Namibian uranium mining projects. However, with the tax and royalty increase initiative since withdrawn, most projects are back on track at this point in time.

Jan 1, 2012

By J. Hart, P. W. Conrad, S. Rosenthal, R. A. Hogan

The Mining Engineering Department at Montana Technological University (Montana Tech) has a new Mine Safety and Health Administration (MSHA) approved program for Part 46 and Part 48 mine health and safety training. The training program will utilize the facilities and faculty from Montana Tech’s Mining Engineering and Safety, Health, and Industrial Hygiene departments to provide superior mine health and safety training to the mining industry. The faculty of each department includes professionals with experience in safety training and the mining industry. The training program incorporates adult learning techniques and extensive hands-on activities in all training modules. The instruction will exceed MSHA requirements. The resources available on Montana Tech’s campus will be utilized to strengthen the training program providing the mining industry with a world class mine health and safety training program.

Feb 1, 2023

By Rodrigo Rocha de Meira

O laminador de tiras a frio n° 3 da CSN apresentava perdas de produtividade ao processar aços de elevada resistência microligados, com limite de escoamento mínimo igual a 340 MPa, dotados de largura superiores a 1400 mm. Devido à crescente demanda do mercado automotivo relativa a esta família de aços, tornou-se necessário um estudo para optimizar a produtividade do equipamento e não desestabilizar o fornecimento aos clientes. O estudo consistiu em testar parâmetros de processo alternativos, objetivando abastecer o laminador de tiras a frio com bobinas laminadas a quente dotadas de resistência mecânica ligeiramente menor, para promover maior estabilidade operacional no equipamento a partir da redução das cargas de laminação. As alterações propostas resultaram no aumento de produtividade do laminador de tiras a frio, sem comprometer as características mecânicas do produto final.

Jul 30, 2018

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitation and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitatton and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By K. E. Stanfield

The oil yields of sections of Green River oil shale in Colorado, Utah, and Wyoming are presented as part of a continuing project to determine oil-shale reserves in the United States. Oil-yield logs, based upon analyses obtained from 1945 through 1952, are presented to show the thickness and richness of 202 sections of Green River oil shale. The logs are based on analyses of approximately 20,500 samples, representing 179,000 feet of shale, which were made by the Bureau of Mines, and upon analyses, representing approximately 26,000 feet of shale, which were made by other agencies. The samples consisted of cores from a Bureau of Mines coring program in U. S. Naval Oil-Shale Reserve 1, Garfield County, Colo., and cores, drill cuttings, and channel samples provided by other agencies, chiefly oil companies. Most of the samples of oil shale from Utah and Wyoming were derived from oil-well drilling operations. As a result, the oil-shale sections were widely scattered and were not extensive or reliable enough to be representative of the significant deposits of Green River oil shale in these States. The oil-shale sections for Colorado, however, were more comprehensive, and a number of the sections were used in a previous report as a basis for estimating oil-shale reserves in Colorado. The present report does not give estimates of oil-shale reserves but is limited to presentation of oil-shale analyses that may be used for future reserve estimates. Other sections of Green River oil shale are being analyzed, and the results will be published in subsequent reports.

Jan 1, 1954

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By K. Whiting

In October 1993, the first two of a series of full scale passive biological treatment cells were constructed to treat mine drainage from the Burleigh Mine (located approximately 48 km west of Denver, Colorado in the Clear Creek/Central City Superfund Site). The two cells are each 19-21 m long, 10.7 m wide and 1.2 m deep. Each cell contains approximately 216 cubic meters of substrate (composted manure) and is designed to treat 60 L/min of mine flow. One cell is designed as an upflow reactor and the other cell is designed as a downflow reactor. The differences in flow hydraulics and treatment efficiencies will be tested in these two cell for approximately nine months before the remaining cells are built to treat all the discharge. The substrate material was selected based on a series of bench scale tests. During the tests, the amount of metals removed was determined. The design flow rate was based on a sulfide generation rate of 400 nanomoles of sulfide generated per cubic centimeter of substrate per day. Metal removal results for the first three months of operation of the two cells will be presented and compared to results of bench and pilot studies at other sites.

Jan 1, 1994

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Paul Sterk

In underground mining a great deal of time, money, effort, and resources have been used in the effort to minimize blast-induced damage. This damage occurs to the back, ribs, and pillars when the energy of the explosive is released back into the rock due to over confinement or the overloading of explosives in the perimeter holes. This damage can result in roof falls, dilution of ore, excessive rock bolting, scaling, screening, shot-creteing and other safety and support issues.

Jan 1, 2003

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By Lijun Lu, Honghui Fang

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 ~ 2% is optimal, where flexural strength is reduced by 10% ~ 23% and compressive strength reduced by 5.7% ~ 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 ~ 2%, the flexural strength is increased by 5 ~ 7% and the compressive strength is reduced by 1 ~ 2%. The results show that the formula two is better.

Jan 1, 2015

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947