Search Documents

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

By S. H. Ash

THIS REPORT covers the second in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the construction work contemplated-to sink two shafts on the line of the main tunnel that are designated the Nos. 9A and 11 shafts, to turn off from the No. 9A shaft the Lansford and Lykens laterals, and to drive portions of the main tunnel. An emergency pumping plant, consisting of 2 separate pumprooms, each containing 3 horizontal-type centrifugal pumps of 100,000-gallons-per-minute (g. p. m.) capacity, will be constructed at the No. 9A shaft. From the No. 11 shaft will be turned off the Trevorton lateral and portions of the main tunnel, which will connect with the section driven from the No. 9A shaft. Under the proposed project, the Lansford lateral will be driven for a distance of 2 miles, the Lykens lateral for a distance of 10.56 miles, and the Trevorton lateral for a distance of 20 miles. To drive the Lykens and Trevorton laterals for the distance indicated, several construction shafts and slopes must be sunk to permit efficient and safe construction.

Jan 1, 1955

By Yunxing Cao, Xinsheng Zhang, Bingbing Meng, Shuaifang Guo, Li Wang, Junsheng Zhang

During the initial process of mining a longwall working face, it is often found that the roof will not collapse readily, which increases the risk of later roof collapse disasters. Explosive and hydraulic fracturing are common roof weakening techniques; however, they have certain limitations. In the present study, CO2 fracturing was used for roof weakening during the initial mining phase in the Changcun coal mine, China, which is a novel strategy. First, by analyzing the lithological characteristics of the working face and applying combined beam theory, the breaking spans of the top coal, immediate roof, and main roof were determined before weakening. An F-35 CO2 fracturing device with a rated pressure of 270 MPa was used, which provides fracturing energy equivalent to 0.968 kg of TNT. The fracture radius of the main roof was studied by ANSYS/ LS-DYNA combined with the hanging roof-breaking theory to determine the optimal layout of CO2 fracturing drills. The results show that the breaking spans of the top coal, immediate roof, and main roof were reduced by 3.99 m, 7.66 m, and 22.03 m, respectively. The main roof collapsed as the working face advanced, eliminating the chance of later roof collapse disasters. Compared with hydraulic fracturing and explosives, CO2 fracturing is safer and more practical, giving it significant application potential.

Nov 23, 2023

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By T. R. Curr, W. A. Gericke, J. Basson

South Africa is a leading player in the international ferro alloys industry. Historical factors that have contributed to this dominant position include an abundance of natural resources and relatively low cost electricity. A number of relatively recent developments are potentially threatening this position. These include new legislation affecting the mining and minerals industry, a shortage of some types of suitable reductants, depletion of surplus electricity generation capacity with resultant threat of real escalation of electricity prices and pressure resulting from the recent strengthening of the South African Rand. The industry is addressing these challenges in a number of ways to ensure long-term viability. Some of these measures include investments in more efficient technologies that have economy of scale benefits and are less dependent on expensive reductants and electricity. Local macro-economic impacts include new legislation regarding ownership of enter-prises, mineral rights and royalties on mineral sales, development plans for port and rail infrastructure, as well as initiatives to expand electricity generation and coke production capacity. The fundamentals for being a successful ferro alloy producer are still largely in place for South African producers. Therefore the South African ferro alloy industry will remain competitive and is well placed for continued growth in line with the international growth in ferro alloy demand. The industry should emerge leaner, more efficient and ready to respond to any future demands of the industry. This paper will cover the present status of the industry, the factors that are impacting thereon and a view on its future outlook.

Jan 1, 2007

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By M. Z. Emad, N. Abbas, Y. Majeed

Room-and-pillar mining is commonly employed for the extraction of rock salt in undergroundmines. Pillar stress is a major concern in these mines as it is directly related to stability and mineralrecovery. In this study a flat jack method was used to measure pillar stresses in three undergroundrock salt mines in Pakistan. The field work included determination of in-situ stress, in-situ elastic modulus, recording of field variables (pillar length and width, height and width of opening, opening width to height ratio, extraction ratio, and overburden height) and collection of salt block samples. The geomechanical properties of rock salt (uniaxial compressive strength, Young’s modulus, Brazilian tensile strength, and density) were also determined to estimate overburden stress, pillar strength, and factor of safety (both estimated and actual). It was found that the measured pillar stresses are proportional to the overburden stress values, with their magnitude ranging from 6.05 MPa to 11.97 Mpa, and the pillars were found to be stable. Regression analysis was performed to develop statistical models for in-situ stress and in-situ elastic modulus. Finally a quick guideline chart was developed to determine the suitable length of pillar for a given span and required level of safety.

Jun 5, 2023

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

COUNCIL OF ECONOMICS OF AIME Formerly Mineral Economics Division Established as a Division December 15, 1948 Established as a Council February 26, 1957 Franz R Dykstra, Chairman Paul Schultz, Vice-Chairman A J Phillips, Vice-Chairman Douglas Donald, Vice-Chairman J S Vanick, Contact AIME Director A H Lindley, Jr, Secretary-Treasurer Lehman Brothers 1 William Street New York 4, N Y COUNCIL OF EDUCATION OF AIME Formerly Mineral Industry Education Division Established as a Division January 15, 1932 Established as a Council February 26, 1957 0 Cutler Shepard,Chairman Lysle E Shaffer, Vice-Chairman John C Calhoun, Jr, Past Chairman J C Kinnear, Jr, Contact AIME Director J D Forrester, Secretary-Treasurer College of Mines Univ of Arizona Tucson, Arizona

Jan 1, 1958

By C. Meyer, J. J. Eidel

C. W. Hunt I wish to register strong disagreement with the choices of drilling sites chosen by the Continental Scientific Drilling Committee, while endorsing the stated objectives. Of special significance is the lack of any site involving the metals most needed today in the US, while 9 to 13 km of drilling are allocated to gold and silver districts and 11 to 17 km to base metal (mainly copper) districts. Why is nothing proposed for platinum group or chromite? Is this because the committee did not know of such a site? If so, I offer such a site in California (see Fig. 1). The mineralization shown in Table 1 occurs in a large peridotite body in western Tehama County, CA. Petrography has demonstrated unequivocal evidence of migrated PGE deposited in peridotite and chromite of hypabyssal nature. Active diapirism (due probably to serpentine buoyancy) above a reactivated mantle to surface conduit marks the position of the conduit. Young explosion breccia cemented loosely by volcanic glass and tuff demonstrates the significance of the conduit as the prime source of the various emissions. Deep drilling could result in major metals discoveries as well as shedding light on the grand questions of platinum group mineralization. What role water has played in this occurrence is not yet certain; but chlorine and asphaltite have been detected in and adjacent to native PGM, suggesting a major role for water. The explosion breccia suggests that this excellent site could overlie entrapped geothermal steam.

Jan 6, 1987

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By W. J. Schitt

Section 15 covers a loose collection of topics that involve water in some way. The chapters in this section include Dredge and Placer Mining (Chapter 15.1), Solution Mining: Surface Techniques (Chapter 15.2), and Solution Mining: In Situ Techniques (Chapter 15.3). The dredge and placer systems involve water in several forms. The segment on hydraulicking or hydrosluicing discusses the use of monitors to direct high-pressure water jets to move material. As such, this represents an alternative to mechanical breakage, loading, and hauling. This chapter also covers placer mining (except dry placering) where the water provides the medium that promotes the separation of minerals based on their density and other settling characteristics. Thus placer mining is generally limited to concentration of gold, tin ore, diamonds, and other heavy minerals that are already liberated and are contained in a less dense matrix. The third topic, straight forward dredging, as in sand and gravel operations, involves water only in an incidental way. Here water simply covers the minerals of interest. Thus the dredging system need only lift a payload from the submerged location to the surface for further processing or handling

Jan 1, 2008

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016