Search Documents

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019

This report, 27th in a continuing series1, describes Bureau of Mines research and technologic work on coal and related investigations during 1962. While the brief discussion in each section of the report presents only the highlights of Bureau work during the year, details of many investigations can be found in publications cited in this text. Other work, reported here for the first time, will be covered in greater detail in later publications. Recent trends in coal research and technology both at home and abroad were reviewed in several publications2. Bureau research, as in the past3, continued to stress improved methods of mining, preparing, processing, and using coal. The program included a wide variety of applied and basic studies for developing information useful to the coal mining industry and the coal consumer while promoting wise conservation and utilization of our coal resources.

Jan 1, 1963

By James Tarr, Matthew Eichler, Brent Tardif

ANFO was being used as one of the blasting agents on a construction site in New England. Groundwater was encountered in numerous blast holes. The blasting contractor was employing typical explosives loading procedures for wet conditions. An abutter to the project complained that blasting caused her well water to have an odd taste and smell. Through testing, it was determined that there were hydrocarbons and nitrates in the well water. Several days later a second neighbor complained of foul tasting water; again it was determined that hydrocarbons and nitrates were present.

Jan 1, 2003

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By Stanley Lefond

The health of the industrial minerals industry appears to be improving year by year. In fact, preliminary information suggests that only three commodities (asbestos, bromine, and sulfur-other) failed to show a production gain in 1984 over 1983. In 1983, 10 commodities failed to post gains and six remained constant. The total value of industrial mineral production in 1984 was $16.7 billion, up $1.4 billion from 1983. Cement, clays, gypsum, and crushed stone production increased. Since these are used in housing and construction, this suggests these industries are moving out of their recent doldrums. Barite and clay production also improved in 1984. Local US barite production, however, still has a long way to go to attain the 1981 high of 2.6 Mt (2.9 million st). Barite imports remain high. But they are not as high as the 1982 importation of 2 Mt (2.3 million st). Bentonite production in 1984 increased 20% in volume and 25% in value over the previous year. This suggests improvement in the drilling industry and an increase in demand for iron ore pelletizing grades. All in all, the industrial mineral industry is alive and well. And it shows signs of great improvement in the next few years. Many thanks to those industrial mineral technical committee members for their assistance in assembling this industrial minerals review: M. F. Dibble, H. W. Allen, G. H. Gallup, S. G. Ampian, D. W. L. Spry, H. G. Fleshman, and L. J. Czel.

Jan 5, 1985

By H. Lyn Bourne

This is the fourth annual tabulation that gives mineral royalty information. The table presents previous information plus about two dozen new entries. In addition to the royalty information, some entries show the cost of purchased reserves. Last year's tabulation appeared in two issues, to accommodate all of the information. This year the format has been changed slightly so the table can be printed in one issue. This year's table presents the commodities in the same sequence as last year. Sand and gravel information appears first, followed by: crushed stone for aggregate; other stone; industrial sand; other industrial minerals; energy minerals (coal, oil shale, uranium); and finally metals. As always, a caveat relates to factors that influence the reserve values. The data should serve only as a general reference. The table is not intended to present an absolute scale of reserve costs. Several factors influence the value of mineral commodities. These factors include: • location and transportation costs (especially significant for most industrial minerals); • market conditions for both the commodity and the company acquiring the right to mine it; • quality or grade of the deposit as it reflects the amount of processing and beneficiation necessary to produce the finished product; • and legislative restrictions and conditions for mining a given material at a given site. These and other factors will influence reserve costs of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity; the location (either by state, US geographic area, or Canadian province); the cost (R for royalty and P for purchased cost); and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cuft), tons (/T) (2000 lbs) or acres (/A). 1 cu yd = 0.76m3 1 cu ft =0.28m3 1st = 0.9 t7 1 acre = 0.40 ha or m2 In several cases the royalty is a percentage of the finished products, sale price and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: J. Dunn, T. Eyde, K. Loda, L. Morgan, F. Nix, H. Sorenson, and L. Williams. Several people have said they would like this to be an annual tabulation. That can happen if new information comes to the writer. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write or call: H. L. Bourne, c/o Neyer, Tiseo & Hindo, Ltd., 38955 Hills Tech Dr., Farmington Hills, MI 48018, (313) 553-6300. Only with new information can this become an annual and current source of reserves costs.

Jan 8, 1986

By Brenton Fletcher, Yongjun Peng, Wonder Chimonyo

As a cheap, renewable and non-toxic material, starch can contribute to the sustainability of the flotation process, albeit in a minor way as one type of reagent in systems involving materials with far greater impact. But the physical and chemical versatility of starch can help address another issue, namely, that of processing complex ores with decreasing grades of valuable minerals and increasing mixtures of gangue. This paper compares the results of two lab scale flotation studies where starches (native wheat starch (NWS), dextrin and two oxidised wheat starches) were used to depress two common gangue minerals, copper-activated pyrite and carbon (graphite), over a range of dosages. The oxidised starch with the larger molecular weight structures depressed copper-activated pyrite best, and the oxidised starch with lower molecular weight structures was better at depressing graphite. In both cases, the oxidised starches allowed greater recovery of chalcopyrite, pointing to selectivity potential. The extent to which the carbonyl and carboxyl moieties of the oxidised starches contribute to depressant performance is difficult to quantify, but it should not be discounted. Importantly, the results demonstrate relatively simple modifications of native starch by oxidation can yield structures suitable for depressing gangue minerals with diverse surface properties. The challenge remaining for greater application of modified starch depressants is being able to replicate the desired structures at scale in cold-water-soluble form.

Jan 18, 2021

By Patrick R. Taylor

A non-transferred arc thermal plasma assisted cyclone reactor has been designed, built and operated to evaluate its use in vitrification of wastes. Simulated waste (liquid, slurry or fine particulate) is injected near the plasma flame, where nearly instantaneous dehydration and calcination reactions happen. A non-transferred arc plasma torch was attached tangentially to the cyclone and is utilized as both an enthalpy source and to provide the gas velocities required to generate the cyclonic gas flow patterns. The closed top cyclone flow sends the solid particulates to the wall, where they are captured by a thin film of molten glass that is injected as a powder at a position lower in the reactor. The molten glass is then collected in a crucible. The feasibility of simulant injection directly into the flame zone and its effect on electrode lifetimes has been studied. Several candidate refractory systems have been evaluated for their suitability for extended use under the demanding conditions present in the cyclone reactor.

Jan 1, 2002

By J. S. Young

During 1975, the Reclasource Corporation constructed and commissioned a plant for the recovery of mill scale, coke breeze, blast furnace dust, blast furnace sludge and basic oxygen furnace dust at the site of Crucible Alloy Division, Midland, Pennsylvania. The Reclaform Process was employed as the criteria for plant design. This Process takes the solid in-plant fines as listed above, commonly found in integrated steel mills, sizes and forms them through the use of a carbonaceous binder briquetting system and cures the binder through a final heat-treating step. 15,000 tons of Reclaform briquets have been tested in the Crucible blast furnace in several campaigns structured to assess material handling properties, burden feasibility and finally culminating in an iron and carbon assessment campaign. Data are presented from the records of the blast furnace operation and conclusions are drawn that both iron and carbon utilization have been demonstrated.

Jan 1, 1977

By Michael G. Rulff, Tracy M. Holmes

"Vast amounts of time and money are spent fighting flow problems in plants that involve the handling or processing of industrial minerals. Because these types of projects tend to be capitalintensive, the right decisions, made at the design stage, can have a substantial positive effect on the economics of the project.Some of the problems related to solids flow in mineral processing plants include:•,Flow stoppages•,Uncontrolled flow•,Segregation of blended materials•,Build-up and dead material resulting in loss of live capacityUnfortunately few Universities in North America provide courses in the design or selection of bulk solids handling equipment, let alone the theory of bulk solids flow, with the result that engineers do not fully appreciate the effects of bulk solids handling on their process. The usual method of selecting “standard” equipment, all too often, leaves plant operators hammering on hoppers to promote flow, a technique that is not only usually ineffective but also unsafe and often causes damage to equipment. In short, too little consideration is given, at the design stage of projects, to the particular material and operating environment involved and how these will affect handling between process steps.This paper seeks to give a general understanding of bulk solids flow theory including flow patterns and flow property tests, and presents functional design guidelines to ensure reliable flow. As well, a case history will be presented. Our message is clear: To ensure uniform, reliable flow, a plant design must take into account the specific flow characteristics of the bulk solid to be handled or processed."

Jan 1, 2008

By Milton Fies

Introduction The first experiment in underground gasification of coal in the United States was conducted at Gorgas, Walker county, Alabama, under a co-operative arrangement between the U.S. Bureau of Mines and the Alabama Power Company, at the suggestion of the Power Company. The test was conducted on property of the Alabama Power Company, that owns some 19,000 acres of coal-bearing lands on which there is developed a highly mechanized mine producing some 2,500 cons of good quality steam coal per day. At the same locality ?there is a 200,000 kilowatt steam plant one of the largest in the southern portion of the United States. The Alabama Power Company owes much of its beginning in 1912 to British vision and courage. The original plans for building hydroelectric plants in Alabama, and for the construction of necessary transmission lines, were submitted to Sperling & Company, bankers of London, who agreed to underwrite certain bond issues, the proceeds of which would be used in launching the new Company on its programme. The set-up by which these funds from England were received was through an intermediary Canadian company, which the English investors desired. The Canadian company - Alabama Traction, Light and Power Company, Ltd. became owner of the securities of the Alabama Power Company and marketed its own securities through the banking house of Sperling & Company. Without assistance at this time the Alabama Power Company could not have gone ahead with its programme of expansion and the bringing together of the properties necessary for laying the foundation for a strong Company, fortified with ample power resources essential for future requirements and for dependable service to the public.

Jan 1, 1948

By Kenneth M. Maas

The Bureau of Mines inventoried the land availability for mineral exploration and development in northern Alaska and compared this land with known mineral terranes and mineral deposits, to quantify the potential for favorable location of mining claims for metalliferous mineral deposits. This report includes thirty-three 1:500,000-scale maps that depict land availability, and the accompanying text and tables relate availability acreage to areas of favorable mineral terranes. Three categories of land availability and ownership are identified, along with 12 subcategories of land status. Available land comprises approximately 14.5 million acres or 16% of the 90.3-million-acre study area; land available with restrictions accounts for 7.5 million acres or 8%; and unavailable land encompasses 68.3 million acres or 76%. Mineral terranes underlie 37.8 million acres or 42% of the study area; 5.3 million acres or 14% are available for mineral location, 2.8 million acres or 7% are available with restrictions, and 29.7 million acres or 79% are unavailable. There are 500 known mineral deposits or occurrences within the study area. This includes 271 lode deposits, of which 171 lie within a recognized mineral terrane and 55 are on available land. The remaining 229 are placer deposits.

Jan 1, 1987

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By S. Saeed, N. Coulson, P. F. Stewart

"The Mine, Health and Safety Act No. 29 of 1996, as amended, embodies worker self-regulation to advance health and safety in the workplace. An important provision for this is the Right to Refuse Dangerous Work (RRDW). This paper explores worker perspectives about the implementation of RRDW on South African mines against a backdrop of revised guidance in the sector: ‘Guideline for a Mandatory Code of Practice on the Right to Refuse Dangerous Work And Leave Dangerous Working Places’, gazetted in February 2016 by the Department of Mineral Resources (DMR). A mixed methods study conducted at mines (n = 14) included a survey of workers (n = 293), focus groups (n = 6) and in-depth interviews (n = 16). Workers reported a high level of awareness, a positive attitude, and experience of the formal RRDW. However constraints to the formal RRDW meant that informal worker resistance to dangerous work was commonplace. Evidence of informal non-confrontational consultation, cooperation, and collaboration in the event of a dangerous workplace also emerged between workers, and supervisors. The research underscores the importance of the RRDW and worker health and safety representatives to mine health and safety. The revised guidance addresses RRDW implementation gaps, but of concern is the potential partiality towards management interests. IntroductionEnsuring that mineworkers act on their duties and responsibilities for health and safety remains a concern across the globe. Article 13 of the International Labour Organization (ILO) Convention Safety and Health in Mines (176 of 1995) entrenched the Right to Refuse Dangerous Work (RRDW) as an important mechanism through which workers act in the best interests of their own occupational health and safety (OHS) and is considered a cornerstone of worker self-regulation (ILO, 1995). Countries ratifying Convention 176 are under obligation to make this right available to workers through OHS legislation that frames the circumstances, procedure, and protection of workers from discrimination in the event of a formal work refusal. The Convention has been ratified by 31 countries, with South Africa becoming a signatory in June 2000 (ILO, 2000). Worldwide studies show that workers use this right with caution (Hilgert, 2013) and cases associated with work refusal are rarely presented in court (Gunningham, 2007; Cooper, 2013). Rather, in cases of formal notification of a work refusal, issues arising out of this are addressed either in the immediate workplace or through the site OHS system and/or at industrial tribunals or similar mechanisms (Harcourt and Harcourt, 2000)."

Jan 1, 2018

By Russell J. Foster

Many important materials are derived entirely or partially as byproducts of primary copper, lead, and zinc production. This U.S. Bureau of Mines report examines the collective role of byproducts with regard to the economics of domestic mineral production, and their individual significance in terms of dollar value, end uses, and strategic considerations. The study also analyzes circumstances that have affected the competitiveness and structure of the U.S. copper, lead, and zinc industries, and factors that impact byproduct availability. These factors include production capacity at smelters and refineries, process technology, changing sources and composition of ores, regulations, foreign ownership, and byproduct demand and price. Policy considerations regarding stockpiling, regulations, and research are assessed.

Jan 1, 1991

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By R Dunne, J Dodd, J Snyder, F Roberto

Energy costs are steadily increasing worldwide while the availability and quality of water are becoming contentious issues between the users (municipalities/households, agriculture, manufacturing and mining). Refractory gold ore treatment - pressure oxidation, biological oxidation and roasting (ultra-fine grinding, or UFG, will not be discussed here as this process only reduces the particle size of the feed prior to cyanidation) - requires substantially more energy and water quantity and quality are vastly different compared to the standard and simple flow sheets used for treating non-refractory ores This paper will provide an overview of the energy and water requirements for treating refractory gold ores, a topic which does not appear to have been considered previously in the literature.CITATION:Roberto, F, Snyder, J, Dodd, J and Dunne, R, 2013. Energy and water requirements in the treatment of refractory gold ores, in Proceedings World Gold 2013 , pp 527-532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By L. Xia, B. Hart, V. Sidorkiewicz

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in North American mining operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper metallurgical operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a mineral variable change in viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides. INTRODUCTION Mineral processing involves enrichment of valuable minerals from an ore, where the separation process utilizes differences between the properties of the value-added and gangue minerals. The properties of minerals, for example composition, specific gravity, particle size, magnetic properties etc., in any flotation feed ore, can vary significantly between the various minerals present. In flotation seperation surface chemistry and wettability is a significant component promoting selective separation of the various mineral phases [1,2] Mineral surface wettability can be changed, advantageously or deleteriously, by many factors including: surface layer alteration through oxidation; galvanic interactions; attachment of secondary precipitates; the adsorption of various reagents [3] In the flotation context the wettability of a minerals surface can be manipulated by various reagents. Collector reagents may selectively attach to specific minerals in the mineral/water slurry enhancing their surface hydrophobicity, increasing bubble-attachment efficiency and improve flotation kinetics and mineral recovery [4]. In contrast, depressant reagents may selectively reduce a minerals surface hydrophobicity resulting in poor particle-bubble attachment and non flotation. In essence, a mineral flotation flow sheet is designed to induce/promote a hydrophobic surface to the value mineral and a hydrophilic surface to all others. Therefore, the versatility of the froth flotation process lies in the selection of different flotation reagents.

Jan 1, 2019

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.