Search Documents

By F. L. Wideman

This paper is one of a series on mining methods being published by the Bureau of Mines. It describes briefly mining practices at the Sunrise iron mine of the Colorado Fuel & Iron Corp., Platte County, Wyo. The Sunrise mine is in the Hartville iron district in east-central Wyoming (fig. 1). The district covers part of the Hartville Mountains, a region of moderate relief in which erosional features have been formed by the dissection of a low plateau. Altitudes vary from 4,300 feet along the North Platte River to 6,000 feet in the uplift. The climate is semiarid, with hot summers and winter temperatures below zero for short periods. Grasses, cacti, yucca, and low desert shrubs grow at lower elevations. Cottonwood and boxelder trees and willows grow along permanent streams; juniper and coniferous trees are confined to the higher elevations.

Jan 1, 1956

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By L. Juteau

"""The north coast of the St. Lawrence River will be the scene of an industrial development during the coming decades"". The facts which underlie this statement are the occurrences of iron and titanium ore, the abundance of hydro-power and the availability of deep-water ports in this region. Havre St-Pierre, Sept-Iles, Port Cartier and Baie Corneau already exist as major ports and urban centers. The huge quartz deposit at Baie Comeau will be a decisive contributing factor in the development of a metallurgical plant in this area. Due to its purity, it lends itself, first of all, to the manufacture of glass of different kinds, being comparable to the quartz sands now used by the plate glass and glass container industries in the Montreal area, Moncton, N.B., Trois-Rivieres and - in the future - at Bécancour, Quebec. However, its high quality will also make it possible to use it as one of the main basic materials for the production of silicon carbide and ferrosilicon, and as a flux in metallurgical processes. It is intended, in this report, to offer conclusive proof of the economical importance of this large quartz deposit by presenting the results of the studies made to date."

Jan 1, 1971

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By S. M. Dar

The U.S. Bureau of Mines constructed a full-scale model of a 15-ft-wide coal mine entry to use in combination with finite-element analyses to investigate roof support systems and various types of roof bolts. The objective was to enhance understanding of the fundamental mechanics of the interaction between rock and supports and the relative integrity of bolted mine roof as a function of roof bolt type, length, spacing, and tension, and the basic characteristics of the roof strata. The laboratory test results, when correlated with computer simulations using fmite-element analysis and underground verification tests, should provide a basis for desigillng safer, more cost-effective roof control systems and help to establish guidelines for employing fully grouted resin and mechanically anchored bolting systems. The background for this research, the research approach, the methods and equipment employed, and the results are described in this report.

Jan 1, 1989

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By Nord L. Gale

Lead, zinc, copper, silver, cadmium and many other heavy metals which are potentially hazardous if released into the environment in wastewater discharges have been of considerable concern to governmental agencies, industry and the general public. In response to this concern, an interdisciplinary research team at the University of Missouri has been funded by the National Science Foundation-RANN program to study trace contaminants associated with the production of lead for the past eight years. Seven modern mines in close proximity to two lead smelters in the forested Ozarks of Southeast Missouri are the largest source of lead in the world and in 1976 alone produced 504,095 short tons of lead, 82% of the United States total production. This new and rapid industrial development in a sparsely populated. rural forest region has offered a unique opportunity for studying the impact of trace metals and for developing improved techniques to control detrimental effects. Research on the wastewater discharges and two methods of biological and recycle control are discussed in this paper. Although the two mine-mill complexes investigated in this study have many similarities, the differences between the two are substantive and warrant separate examination.

Jan 1, 1977

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa&apos;s water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy&apos;s Law Q = PIA where:

Jan 1, 1974

By Randal Martin

Recently, questions regarding the influence of atmospheric temperature and humidity levels on airblast levels have arisen at a number of blast sites. Humidity is alleged to have contributed to high levels of disturbance within communities surrounding blasting. In some cases, local regulatory agencies considered adopting guidelines to specify humidity and temperature ranges under which blasting cannot take place. However, it is normal blasting industry practice not to consider humidity or temperature effects, in the absence of inversions, on airblast levels. When blasting is conducted in the vicinity of residential structures, the influence of weather on the propagation and attenuation of airborne noise from the blasting site is always a concern. Sound naturally attenuates in air with distance from the source. A part of this attenuation is attributed to divergence at the airblast wave front, while the remainder of the attenuation is an accumulation of various factors that include temperature and barometric pressure, absorption in air due precipitation and vegetation, wind and temperature gradients, atmospheric turbulence and topography (Beranek, 1971). Wind speed and wind direction, as well as vertical and horizontal temperature gradients can cause airblasts to focus in local regions surrounding blasting operations and may result in air pressures greater than expected. In fact, wind and temperature inversions can actually increase sound levels with distance from the blast site. Close to the blast site, the effects of inversions may be negligible but may exceed 10 dB at 800 m or greater (Davis and Cornwell, 1991).

Jan 1, 2001

This paper reviews rehabilitation, closure, and post-closure management of the Tui, Golden Cross, and Martha Mines, all of which are located in the Waikato Region of New Zealand. There was no requirement for rehabilitation of the Tui mine, which was abandoned in 1973. There was a requirement to rehabilitate the Golden Cross mine. Mining at that site ceased in 1997, and rehabilitation is now well advanced. When first approved, there were some requirements for rehabilitation of the Martha Mine, but when reconsented in 1998, those were extended, and in addition a requirement for post-closure management was included. As a result, a Trust, funded by the mining company, has been established to take long-term responsibility for the site following completion of closure. The different rehabilitation/closure requirements at each of these sites illustrates that we have learnt something from the experiences of the past.

Jan 1, 2003

By Devin Burns, Saima Ghazal, Michael Owusu-Tweneboah, Kwame Awuah-Offei

Trust in AI systems and the nature and amount of information about the system can influence decision-making. It is, therefore, crucial to understand how AI-powered monitoring systems (e.g., gas monitoring systems) influence miners’ trust and decision-making in emergency evacuation. This work focused on measuring the differences between how participants respond to a simulated underground mine emergency evacuation situation when warnings are represented as coming from a human or AI-based monitoring system. We also manipulated the amount of information participants received about the system, yielding a 2×2 between-participants survey design. The participants received an alert message about rising gas levels in a mine and provided a response on how they would react and reported their perceived safety. We also asked questions to assess their trust in, preference for AI over human-based gas monitoring systems, and whether they are willing to delegate the duties of underground gas monitoring to AI systems. The experiment results show the amount of information had a significant influence on miners’ trust and decision-making. The safety perception of participants based on age, number of children and ethnicity was significantly different from one category to another. This work provides valuable insights as the mining industry deploys AI systems to aid mine safety.

Feb 1, 2025

By Jan M. Peter

Many massive sulfide deposits and districts around the World contain rocks that are variously referred to as ?exhalites?, banded iron formation (IF), ?Algoma-type? IF, ferruginous chert, jasper, jasperoid, cherty tuff, tuffite, tuffaceous exhalite, chloritic IF or sulfide IF. With few exceptions, such rocks are thought to be (in part) fossil hydrothermal sediments deposited from hydrothermal fluids vented into a submarine rift environment. Such hydrothermal sediments are associated with a wide variety of ancient base-metal sulfide deposits (e.g., Cyprus-, Besshi-, Kuroko-, and Broken-Hill-type deposits), and hydrothermal sediments are commonly associated with some of the largest base metal sulfide deposits in the world. Analogs of ancient hydrothermal sediments can be found around many modern seafloor hydrothermal deposits which themselves precipitate from high-temperature (350°-400°C) hydrothermal fluids. Hydrothermal fluids are quenched on contact with ambient seawater, and most of the metals are immediately precipitated to form the mound and chimney deposits. However, for kinetic and solubility reasons, not all metals and other species are immediately precipitated at the vent site. Fine particles (up to several hundred microns in diameter) of sulfides, sulfates, carbonates, oxides, silica, Fe-oxyhydroxides, clays, and other phases are precipitated from the hydrothermal fluids in the water column above the deposits. These particles or "particulates" are carried upward for several hundred meters in a buoyant hydrothermal plume (which is typically several hundred meters thick) until it reaches a neutral density, and disperses laterally from the vent site. Modelling of plume dynamics has shown that the majority of particulates are deposited by gravitational settling a few hundred meters from the vent site, and Å99% of particulates are deposited within 3 kilometers. However, signals from modern plumes have been detected even hundreds of kilometers from their source. Factors which can affect the morphology of the plume (and the resultant fallout pattern) include: particulate size, shape and density, bottom topography, and the direction and velocity of bottom currents.

Jan 1, 1998

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

By Jim Sadowski, Steve Stewart, Bob McMurdy, Martin Nevens

"Mohawk Garnet has been operating a small pilot plant near Sudbury, Ontario for several years attempting to produce commercially viable garnet. The challenges of operating a pilot scale mining, processing, and product handling operation as a full time plant have led Mohawk Garnet to seek a better way. In co-operation with Mohawk Garnet, Outotec (USA) Inc. has taken on the technical and design challenges of increasing garnet product from twenty tonnes per day to two hundred tonnes per day.Outotec performed a comprehensive test and flowsheet development program applying Outotec’s density separators, spirals, flotation, and other technologies to design a successful process for the separation and recovery of the valuable garnet for Mohawk.This paper explores the test program, the process flowsheet development work, plant design and preliminary engineering of a new garnet processing. The various technical challenges, process technologies involved, and design concepts will be discussed.INTRODUCTIONMohawk garnet has been operating a small-scale garnet mine and process plant in Wahnapitae, Ontario near Sudbury.The current operation was intended to be a pilot plant and so only produces 20-25 tonnes of garnet concentrate per day. The garnet is bagged and sold for use as abrasive. The process is inefficient with low yields, poor material handling and very high cost per tonne. Mohawk garnet approached Outotec to help them improve their garnet process and transform themselves into a larger scale and more efficient operation."

Jan 1, 2010

Greater mining productivity requires a more efficient cutting process. The cutting force available from today?s mining machines has been optimized with respect to machine size and weight. Researchers have shown that when employing water-jet-assisted cutting, bit forces and drum torques can be reduced significantly, which may allow mining machines to become lighter and more efficient. The Bureau of Mines has initiated a program to develop a water- jet-assisted rotary cutting system using the conventional bit assisted by a directed water jet operating at moderate pressures (3,000 to 10,000 psi). This water-jet-assisted cutting system has the potential to improve cutting efficiency without increasing machine horsepower or water usage (beyond what is presently used for dust control) or requiring fundamental changes in mining practice. IR addition to improvements in productivity, other anticipated benefits of water-jet cutting include reduced generation of respirable dust, elimination of frictional ignitions, increased bit life, reduced fines, and fewer machine vibrations. The papers presented at this open industry meeting discuss the development of water-jet-assisted cutting technology and future application of this technology to a variety of mining techniques including roof drilling and longwall mining.

Jan 1, 1985

By Yoshihiko Maeda

It is said that the 21 st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980th due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologies and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

In their excellent paper, Milev and Spottiswoode have provided quantitative and definitive descriptions of an important phenomenon that hitherto has been largely the subject of conjecture. They convincingly show that ?site-response? can amplify the strong ground motions on the rock-wall of a stressed tunnel by a factor of 10 to 12 compared with the PPV in the solid rock mass (at the same distance from source). This knowledge gives us a firm foundation from which to begin to build an understanding of the mechanism of damage resulting from a rock burst. Regrettably this understanding is still far from adequate, in my opinion. The authors of this paper, however, have made some statements that are too reassuring and which tend to reinforce the sense of complacency that prevails among many members of the rock engineering community on the deep gold mines.

Jan 1, 2006

By Neil J. Mansfield

Tool manufacturers are required to provide declarations of vibration emission values in order to sell their tools within Europe. To ensure that users can compare results obtained from different manufacturers, the declared values must be obtained using a methodology as specified in the relevant test code (such as in the ISO 8662 series of standards). In most cases, the vibration emission values obtained using test codes under-estimate the vibration that an operator will be exposed to when using the tool on a work-site. A further problem with manufacturers’ data is that usually only a single value is provided for a tool. This is despite many factors affecting the vibration emission, including inserted tool type, work piece, operator technique, tool condition. New improved test codes are in the process of being developed. In order to provide guidance to users on how to interpret manufacturers’ data, a Draft CEN Technical Report (Draft CEN/TR 15350 (2005)) was developed. Part of the CEN/TR provides multiplication factors for combinations of task and tool type. For example, data obtained from electrical hammer drills (tested according to EN 60745-2-6:2003) should be multiplied by 2, for hammering applications, in order to obtain an estimate of the vibration emission during work. In response to concerns from industry, the UK trade association OPERC have, in collaboration with hire companies and tool manufacturers, established a freely accessible online database of tool emission values based on independent tests carried out under simulated work-site conditions. This paper reports some of the data obtained from electrical hammer drills, highlighting the range of emission values that can be obtained for a tool. Data from many other tool types are also included in the database. Methods Tri-axial hand-arm vibration was measured at both handles of each of 19 electrical hammer drills, in accordance with ISO 5349-1 (2001). Each tool was measured with three experienced operators and at least 5 runs were completed for each operator. Tools were tested using a range of appropriate new bits from 4 to 40 mm diameter. The minimum number of bits for a tool was 3; the maximum number was 29. 146 tool / bit combinations are reported here, representing about 2200 individual 6-axis measurements. Operators were required to drill vertically into a concrete block with a compressive strength after 28 days of 40 N/mm². Two drills (1 and 15) were battery powered; others were powered using a 110V transformer supply.

Jan 6, 2006

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in intensified efforts in inspections of coal refuse sites by the Mining. Enforcement, and Safety Administration (MESA). MESA inspections however, are mainly qualitative and are often time consuming, Therefore, in August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in MESA inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photo interpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Based on CH2M HILL results cost for monitoring by rapid system was approximately 25 percent of cost by conventional ground survey.

Jan 1, 1980